Question about Ford Cars & Trucks

1 Answer

How do I change my oil pan gasket on my 95 ford Thunderbird, thank you first time car owner

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,335 Answers

Lift your car and place on jack stands. Then drain engine oil from pan. If there is/are any other steering or suspension components under oil pan, remove these first. Then, begin removing all bolts that hold pan in place. There should be a few bolts that come from the rear of the transmission section that also hold engine oil pan. Remove these. Once all bolts are removed, use a rubber mallet to tap oil pan until is breaks loose. If hard to remove, use a pry bar or flat head screw driver to pry oil pan off. Install in reverse order.

Posted on Dec 30, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing a oil pan for a 95 grand marquis


Just loosen oil plug and drain...take out pan bolts... drop down...make sure alt gasket material is off of both pan and bottom of motor. Lay new gasket on oil pan...possibly use gasket sealer to keep gasket in place...a very thin layer on oil pan then put gasket on. Let dry for a bit then bolt back up...make sure oil plug is back in then refill....cheers!

Dec 12, 2016 | 1995 Mercury Grand Marquis

1 Answer

I have a 95 t-bird and oil leaks in front by the oil pan having to put oil in it once a week could be the gasket around the the oil pan


It could be the oil pan gasket or the front seal behind the harmonic balancer(which is quicker and easier to fix) and it sounds more like the front seal is your issue.

Feb 18, 2011 | 1995 Ford Thunderbird

1 Answer

How do i fix my 95 ford thunderbird? it's pouring oil out of the bottom of my engine only when i crank it up.


There are many, many things that could be causing the problem. Short of a hands on diagnostic, the list is very daunting to go through. There are some basic things you could check first before you have4 it towed to a shop. Block your rear wheels so the car can't move then raise the front end so you can get under it. Get a flashlight or drop light and start looking at the oil pan and block for holes. You will see a trail of oil from where it is coming out and just follow that to the problem. It could be a loose or missing oil filter or a hole in the oil cooler, oil pan, cylinder head or block, or a torn gasket or warped component.. Any way you look at it repairs are needed before you attempt driving - you could ruin the engine quickly if you try to drive it, even just 1 mile. Check the oil level before you raise the car or go under to make sure you still have oil in the motor. Do not try to start it as this could also ruin the motor, requiring a new motor to be installed which would cost more than the car is worth.
Good luck!!

Nov 27, 2010 | 1995 Ford Thunderbird

1 Answer

95 mustang gt how to change oil pan gasket


There is no simple way.. I have done it with the motor in and out.. It took less time to pull the motor and change the pan than it did to drop the cross member , undo the engine and trans mounts. I don't recommend doing it with the motor in.

Jul 28, 2010 | 1995 Ford Mustang

1 Answer

Do i need to drop the oil pan to ghange the timing cover gasket on a 95 ford mustang v6?


You can pull the motor mounts bolts and jack the motor up alittle, that will give you enough clearance to drop your oil pan. If you try and replace the timing chain cover without dropping the oil pan, you will more than likely wind up with an oil leak.

You should be able to replace the timing cover without removing the oil pan. The gasket set should contain gaskets allowing you to cut the oil pan gasket and put in a new partial gasket in this area. In the corners make sure you use some RTV sealant. If you are careful, it can be done. Like Bob A says you can end up with a oil leak without dropping the pan (unless you clean up the area and properly apply the RTV and gasket). If you have time to drop the oil pan, then I would do that.

Oct 21, 2009 | 1995 Ford Mustang

1 Answer

1996 ford T-bird Lx V6 trying to remove timing chain cover to replace gasket ( oil leak above filter housing. All bolts I can see are removed, does the oil filter housing have to be removed also > and...


cover has 2-4 bolts at front of oil pan and harmonic balancer will need to be removed to take cover of of crankshaft.. lemmee kno if that solves your problem...chris..

May 09, 2009 | 1996 Ford Thunderbird LX

1 Answer

Changing oil pan gasket on 1989 Ford Aerostar


drain the oil from the pan and remove the filter.
Lift the car up and secure it . So it will not roll or fall. Remove the bolts from the pan using a 10 mm or so and a rachet and small extension. There are several bolts all around the pan. Remove the pan and remove the gasket. Clean up the pan and remove all gasket material from the pan. Install the new gasket around the pan and replace back.

Apr 05, 2009 | 1989 Ford Aerostar Cargo

1 Answer

Oil pan for 1993 thunderbird


No you done have to drop any thing, you just need a new oil pan and gasket for it, loose all bolts around the oil pan and you should be able to remove it, remember remove all the broken off of the old gasket very well before you apply a new one on with grease or gasket cilicon stuff then new oil pan, good luck.

Sep 13, 2008 | 1993 Ford Thunderbird

1 Answer

1994 ford thunderbird 3.8 oil pan inframe removal


PULL IT...front support cross member blocks it. Engine is an easy pull. Having oil pressure problems? Mine first went out with oil pressure dropping at idle and red lights, speed up and it would be ok until the rod knocking. Then it was time to remove and have crank checked and polished or reground. Might as well overhaul engine at this point of it being out.

Aug 06, 2008 | 1994 Ford Thunderbird

1 Answer

To change the oil pan gasket in a 93 Tercel


is not hard, i changed mine 95 tercel

Jul 22, 2008 | 1993 Toyota Tercel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...