Question about Peugeot 407

Open Question

My peugeot 407 hdi has been on diag and glow plug fault. and coolent bypass valve short circuit.. engine now chugging like fuel shortage but new filter fitted.. i cant afford to waste good money .

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2001 Peugeot HDI fuel starvation .

does it get worse as it runs? this would indicate exhaust problem. could be mass air flow

Posted on Oct 10, 2008

  • 1201 Answers

SOURCE: fault code p0245 puegoet 406 turbo fault

My book shows that P0245 is the super/turbo charger solenoid "A" voltage is low.

Posted on Sep 29, 2009

Testimonial: "cheers for that x18wheeler60 thought it was low pressure not voltage,dont suppose you no which selonoid might be causing this nightmare."

  • 4 Answers

SOURCE: peugeot partner wopnt start replaced glow plug

what voltage u getting ?. did it just stop and then not restart. if its getting fuel and glow plugs are working the next two items id look at is the cam shaft and crank shaft position sencors. also make sure ur battery is in good condition, so starter motor is turning fast enough to build up the correct pressure on the rail.

Posted on Dec 14, 2009

  • 10421 Answers

SOURCE: What could cause the diesel from not reaching the

Do mean the diesel fuel? Please check the fuel pump for malfunction. You may need to check also the pump relay and power cables. Regards

Posted on Mar 08, 2011

  • 202 Answers

SOURCE: peugeot 407 coupe 2.7 hdi p0069 fault code comes

o2 sensor needs to be replaced and computer reset by disconnecting battery negative cable for 1/2 hr then reconnecting. Good Luck!

Posted on Oct 20, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

D16y7 1.6l vtec obd2 code p1259 crank no start

Definition of check engine code P1259:
VTEC System Malfunction
Glow Plug Module Control Over Current
Immobilizer to PCM Signal Error
Immobilizer to PCM Signal Error
VTEC System Circuit Fault (Bank 1)
Engine Coolant System Valve Short to Ground
Engine Coolant System Valve Short to Ground

Sep 15, 2017 | Cars & Trucks

1 Answer

I have a Peugeot 407 error codes p1447 and p1351 are coming up anyone know

P1447 ELC system closure valve Flow fault
EDC15C2- PEF filter pierced or differential pressure incorrect.

P1351 IDM input circuit Malfunction/Ignition coil control circuit High voltage
SID 803 - Pre/Post heating relay circuit. Relay not controlled and glow plugs supplied.

save this,it is codes for your peugot,,

May 06, 2017 | Peugeot Cars & Trucks

1 Answer

What could be the problem with my cooling circuit bypass valve solenoid ?and where is it situated on my peugeot 407 hdi 2ltr?.

its located at the back of the engine in front of where the heater pipes go in to the car interior

Dec 12, 2016 | Peugeot 407 Cars & Trucks

1 Answer

My peugeot 407 hdi 1.6 depolution system faulty came on and engine managment light . Car blew smoke now won't start what is it

could be a lot of things, blocked dpf filter, egr valve stuck open, injector stuck. need to have it plugged in to see what faults the ecu is holding.

Nov 27, 2013 | Cars & Trucks

1 Answer

How to set ignition timing on a 407 peugeot

i have a peugeot 407 hdi 2.0 turbo 16 valve engine and i wont to now more about timing markes where is

Jan 22, 2013 | Peugeot Cars & Trucks

1 Answer

What could cause the diesel from not reaching the engime of Peugeot 407 HDi diesel engine

Do mean the diesel fuel? Please check the fuel pump for malfunction. You may need to check also the pump relay and power cables. Regards

Mar 08, 2011 | Peugeot 405 Cars & Trucks

2 Answers

Peugeot 407 2.0 hdi lots of black smoke when you put your foot down past 2000 rpm

The reason for the black smoke is that it is not getting enough air to burn the fuel completely.It could be a blocked air filter,obstruction in the air intake system,blown turbo,hole in tube between intake manifold and turbo,or a fault with the fuel system and injectors.

Nov 06, 2009 | 2006 Peugeot 604

3 Answers


I had same problems with my 307 hdi, turned out that the additive which drips into fuel was empty and changed particle filter,problems solved

Jan 31, 2009 | 1987 Peugeot Liberte

2 Answers

I have a citroen xantia 2.0 hdi,glow plug light goes out to quickly not on long enough,problem still there even after new glow plugs were fitted, would apreciate help thanks.

have you tried the glow plug relay? or if you have a test light see if theres power to glow plugs when light is on,should only light for 5 or so seconds.some of the newer hdi dont even use the glow plugs till temp is very cold,i have a 2006 2.0 hdi van and glow plug light only stays on for a second or so,and its been like that from new! is the problem just bad starting? and is it only when its cold? if you have a manual priming pump for fuel under bonnet,trying pumping before starting it could be fuel prob?ie air getting into fuel system

Nov 02, 2008 | Peugeot 604 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

mike hayward

Level 2 Expert

279 Answers

Wahs Team

Level 2 Expert

215 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides