Question about Cars & Trucks

Open Question

How do i adjust he'd height of the rear hatch to keep it lower

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 3519 Answers

SOURCE: which way do I turn the rear spring adjustment to lower the height on a 82 kz750?

Hi William:
Here's a great article on your bike.
http://www.ridermagazine.com/manufacturer/kawasaki/retrospective-kawasaki-kz750-e-1980-1982.htm/
Cheers.

Posted on Sep 16, 2015

Ad
topslosher
  • 47 Answers

SOURCE: I need for the rear hatch to stop at a height lower than it's normal position. How do I make that adjustment.

their is a button on the side of the hatch you push

Posted on Dec 30, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air supension stays too high


There could be a couple of problems, first and easiest is the rear height sensor became disconnected from its mount. This is common because the sponsor clips on by a kinda weak spring and can be easily disconnected.also where the sensor mounts is a small round metal ball that screws onto frame and rear suspension, the balls after time wear to the point that the sensor spring cannot hold on.there's also an adjustment on the lower mount, if you move it up the vehicle will lower....then you could have a concern with the air compressor vent not allowing it to vent down to ride height. Or the vent solenoid on top of each bag stuck also not allowing it to vent..to ck it yourself, go for a short ride around the block and when you come back park on a level surface, shut off car, exit and close door....listen for an auditable click in the rear, and front left corner of car and watch the distance between rite and wheel lip, see if it drops. If it does I would be leaning towards the simple adjustment...also check thr front ride height on level surface, if you have a suspension problem on 1side of the car and it sits lower,it will throw off rear ride height. ...

Jun 10, 2014 | 1995 Lincoln Town Car

1 Answer

Where is the fuse for the rear hatch on a 1993 chevrolet blazer? My rear hatch will not open at all. I can hear it ttrying to unlatch the rear windoiw but nothing happens.


If you can hear it then you don't have a fuze problem. More than likely it can be fixed by adjusting the catch in the tailgate. Open you hatch with the key and lower the tailgate. Remove the tailgate interior panel/cover and you'll see the catch for the window. Adjust the catch a little, tighten it up, raise the tailgate and close the hatch. Try your release on the dash again and see if this fixes the problem. You may have to repeat this a couple of times until you get it adjusted to where it needs to be. If this works, then reinstall the tailgate interior panel and you're all done.

Feb 17, 2011 | 1993 Chevrolet S-10 Blazer

1 Answer

Front end air suspension in cold weather acts up. I am in FL so I cannot imagine what it would do up north. It will correct itself after it has warmed up. The check air suspension message does NOT come on....


year?

SECTION 204-05: Vehicle Dynamic Suspension — 4-Wheel 2003 Expedition/Navigator Workshop Manual
DESCRIPTION AND OPERATION Vehicle Dynamic Suspension The four wheel air suspension system is comprised of the following components:
  • service switch
  • control module
  • two front height sensors
  • one rear height sensor
  • compressor and drier assembly (includes vent solenoid)
  • air lines
  • front and rear air spring and shock absorber assemblies
  • four air spring solenoids
-------------------------------------------------------------------------------
Principles of Operation
The 4-wheel air suspension (4WAS) module commands changes in vehicle height that are necessary for both the load leveling and the vertical height adjustment features.
The 4WAS load leveling feature automatically makes adjustments in vehicle height so that the vehicle is always at trim height, and that constant front-to-rear vehicle attitudes are maintained over the load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle left and right sides for the 4WAS system are restricted to what can be reliably achieved with three height sensors.
The height adjustment feature has three vehicle heights within a two-inch span:
Kneel height — improves the ease of entering and exiting by lowering the vehicle one inch below the trim height in the front and rear when the vehicle ignition is in the OFF or LOCK positions and the vehicle is stationary.
Trim height — normal vehicle ride position; vehicle moves to trim position when the ignition is ON, when the transmission is initially shifted to DRIVE or REVERSE mode, when all doors are closed or when speed of more than 24 km/h (15 mph) is detected.
Off-road height — improves ground clearance by raising the vehicle one inch above trim height in the front and rear when the vehicle is at 4x4 low modes and the vehicle speed is less than 40 km/h (25 mph).
The 4WAS module uses the universal bus protocol, (UBP), module communications network for sending and receiving various signals with the exception of speed, information from the three height sensors, and the air suspension service switch. For additional information about UBP, refer to Section 418-00 .
The 4WAS system holds vehicle height when any door or rear hatch is opened. The system stores front and rear vehicle height the moment any door is detected open. The system then maintains this height regardless of the addition or removal of a load. The system returns to its commanded height when all doors are closed or vehicle speed exceeds 24 km/h (15 mph).

---------------------------------------------------------------
Air Suspension Service Switch
The air suspension service switch signal is needed to wake up the 4WAS module. Without the module receiving this signal, the 4WAS system is inoperative at speeds below 24 km/h (15 mph) and will not react when the vehicle is raised or lowered. At speeds above 24 km/h (15 mph), the system will be active as if the air suspension service switch is in the ON position.
---------------------------------------------------------
Air Compressor
The air compressor:
  • consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • is a single cylinder electric motor driven unit that provides pressurized air as required.
  • is powered by a solid state relay, which is controlled by the 4WAS module.
  • passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • has a single port drier that can be replaced separately.
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the 4WAS module determines that lowering is required.
  • provides an escape route for pressurized air when system pressures exceed safe operating levels.
  • has a 1034 kPa (150 psi) internal relief valve.
  • is installed with the air compressor as a unit.
Air Spring
The 4WAS system has front and rear air springs. The air springs provide a varying spring rate proportional to the system's air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system's air. Increasing air pressure (compressing) raises the vehicle; decreasing air pressure (venting) lowers the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the 4WAS module command.
Air Lines and Fittings
NOTE: Apply a soapy water solution to the air lines to verify the location of air leaks. If the air lines are cut, ruptured or leaking, a service repair kit is available.
Nylon air lines with quick connect fittings connect to the air compressor and air spring solenoids. The compressor assembly output line is divided by the use of a fitting to supply the front and rear air springs. Fittings are also used to divide the air supply to the RH and LH air spring solenoids.
Air Suspension Height Sensors
There are two sensors used for the front suspension and one sensor used for the rear suspension. The sensors send a voltage signal to the 4WAS module. The output ranges from approximately 4.50 volts at minimum height (when the vehicle is low or in full jounce) to 0.50 volt at maximum height (when the vehicle is high or in full rebound). The sensors have a usable range of ± 45° compared to total suspension travel of 196 mm (7.84 in) at the front wheels and 240 mm (9.6 in) at the rear wheels. Therefore, the sensors are mounted to the suspension at a point where full suspension travel at the wheel is relative to the travel at the height sensor. The front height sensors are mounted to the frame and the links are attached to the upper arm ball studs. The rear height sensor is mounted to the frame and the link is attached to the rear lower arm ball stud.
When the height sensor indicates that the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the system. When the sensor indicates that the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the system to lower the vehicle to its trim height level.
Compressor Relay
A solid state relay is used in the air suspension system for compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the 4WAS module.
The compressor solid state relay is energized by the 4WAS module to have high current flow from the battery to the compressor motor.
4-Wheel Air Suspension (4WAS) Module
NOTE: The 4WAS module must receive a ride height adjustment calibration and must pass a pneumatic test when it is installed new or swapped.
The 4-wheel air suspension (4WAS) module controls the air compressor motor (through a solid state relay), all air spring solenoids, and provides power to front and rear height sensors. The 4WAS module also controls vehicle height adjustments by monitoring the three height sensors and other universal bus protocol (UBP) signals. The 4WAS module conducts all fail-safe and diagnostic strategies, and contains self-test and communication software for testing the vehicle and related components.
The 4WAS module monitors and controls the air suspension system through a 26-pin, two-way connector. The 4WAS module is keyed so that it cannot be plugged into an incorrect harness. There are two harness hardshell connectors and each is uniquely colored and keyed to prevent reversed connections.
-----------------------
  • The air compressor continuously cycles with the ignition switch in the OFF position and no DTC is set
  • Circuitry.
  • Air suspension relay.
  • 4WAS module.

Oct 21, 2009 | Lincoln Navigator Cars & Trucks

3 Answers

No power to rear bags its down but wont air up bags dont seem cracked unplugged connector no power I tried resetting still no power


is switch on?
The air suspension switch and bracket is mounted below the RH side of the instrument panel.

Dealer can run diagnostic test with scan tool for fault codes.
----------

The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving conditions:
  • Ride is improved by using an air type spring (the soft ride is inherent).
  • Handling is improved by maintaining constant vehicle attitude.
The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).
------------------------------------
Air Spring
RAS vehicles use air springs in the rear. The air springs provide a varying spring rate proportional to the systems air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system air. Increasing air pressure (compressing) raises the rear of the vehicle while decreasing air pressure (venting) lowers the rear of the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the air suspension control module.
The two air springs support the conventional rear leaf coil springs.
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing the vehicle and related components.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
------------------------------------------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Restricted suspension movement
  • Excessive vehicle load
  • Cut, severed or crimped air line(s)
  • Unmounted height sensor
  • Damaged air spring(s)
  • Open fuses:
    • Central junction box (CJB) Fuse 4 (15A), 6 (5A) and 20 (5A)
    • Battery junction box (BJB) Fuse 109 (50A)
  • Loose, corroded or disconnected connectors
  • Air suspension switch is in the OFF position
  • Damaged solenoid valve(s)


-----------------------------------------------------------
  • The compressor is inoperative
  • BJB Fuse 109 (50A).
  • Air compressor assembly.
  • Circuitry.
  • Air suspension relay.

Apr 30, 2009 | 2000 Ford Expedition

2 Answers

Airride suspension won't deflate only inflate


It will only process a "down command" if it thinks all the doors are closed. If you have a bad door switch, it won't lower. Any courtesy lights on with doors closed?
The dealer can conduct a diagnostic scan test and retrieve any codes that will help identify the bad circuit. Did they do that?

Do you have 4 wheel air suspension or just rear?

Assuming rear only:
The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.

Note this section.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).

Air Suspension Switch
The air suspension switch supplies power to the air suspension control module. Without the air suspension control module receiving this power, the load leveling system is inoperative and will not react when the rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off the air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
--------------------------------------------------------------------
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • has a 1,103 kPa (160 psi) internal relief valve.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the air suspension control module determines lowering is required.
  • provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
  • is replaced with the air compressor as a unit.
---------------------------------------------------------------
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing the vehicle and related components.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
---------------------------------------------------
May be a bad module too.

Apr 11, 2009 | 2000 Lincoln Navigator

1 Answer

EXPEDITION REAR AIR RIDE PROBLEM


do you have just rear air suspension? here's rear only. 4 wheel different. Deler an run a diagnostic test with WDS machine and get fault codes.
-------------------------------------------------------------------------------------
The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving conditions:
  • Ride is improved by using an air type spring (the soft ride is inherent).
  • Handling is improved by maintaining constant vehicle attitude.
The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).
----------------------------------------------------------------------------------------
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level
------------------------------------------------------------------------------
  • Uneven vehicle height
  • Circuitry.
  • Rear pneumatic fault.
  • Air compressor assembly.
  • Air suspension control module.
  • Go To Pinpoint Test I .

Feb 21, 2009 | 2001 Ford Expedition

2 Answers

AIR SUSPENTION WORKS ABNORMALY


a lot of info here:
Principles of Operation
The 4-wheel air suspension (4WAS) module commands changes in vehicle height that are necessary for both the load leveling and the vertical height adjustment features.
The 4WAS load leveling feature automatically makes adjustments in vehicle height so that the vehicle is always at trim height, and that constant front-to-rear vehicle attitudes are maintained over the load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle left and right sides for the 4WAS system are restricted to what can be reliably achieved with three height sensors.
The height adjustment feature has three vehicle heights within a two-inch span:
Kneel height — improves the ease of entering and exiting by lowering the vehicle one inch below the trim height in the front and rear when the vehicle ignition is in the OFF or LOCK positions and the vehicle is stationary.
Trim height — normal vehicle ride position; vehicle moves to trim position when the ignition is ON, when the transmission is initially shifted to DRIVE or REVERSE mode, when all doors are closed or when speed of more than 24 km/h (15 mph) is detected.
Off-road height — improves ground clearance by raising the vehicle one inch above trim height in the front and rear when the vehicle is at 4x4 low modes and the vehicle speed is less than 40 km/h (25 mph).
The 4WAS module uses the universal bus protocol, (UBP), module communications network for sending and receiving various signals with the exception of speed, information from the three height sensors, and the air suspension service switch. For additional information about UBP, refer to Section 418-00 .
The 4WAS system holds vehicle height when any door or rear hatch is opened. The system stores front and rear vehicle height the moment any door is detected open. The system then maintains this height regardless of the addition or removal of a load. The system returns to its commanded height when all doors are closed or vehicle speed exceeds 24 km/h (15 mph).


Vehicle Height Modes Ignition State Transfer Case Mode Speed or Speed Range Resulting Vehicle Height OFF 4x2, A4WD, 4x4 HI N/A Kneel (TRIM - 25 mm) ON and RUN 4x2, A4WD, 4x4 HI All speeds TRIM ON and RUN 4x4 Low Below 40 km/h (25 mph) Off-Road (TRIM + 25 mm) ON and RUN 4x4 Low Above 40 km/h (25 mph) TRIM OFF 4x4 Low N/A Stays at current position (prior to ignition transition)
Air Suspension Service Switch
The air suspension service switch signal is needed to wake up the 4WAS module. Without the module receiving this signal, the 4WAS system is inoperative at speeds below 24 km/h (15 mph) and will not react when the vehicle is raised or lowered. At speeds above 24 km/h (15 mph), the system will be active as if the air suspension service switch is in the ON position.
Vehicles without message center When the air suspension service switch is in the OFF position and the ignition switch is in the RUN position, a "CHECK SUSP" will appear in the RH corner of the instrument cluster.
Vehicles with message center When the air suspension service switch is in the OFF position and the ignition switch is in the RUN position, the message center will display "SUSPENSION SWITCHED OFF"
Air Compressor
The air compressor:
  • consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • is a single cylinder electric motor driven unit that provides pressurized air as required.
  • is powered by a solid state relay, which is controlled by the 4WAS module.
  • passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • has a single port drier that can be replaced separately.
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the 4WAS module determines that lowering is required.
  • provides an escape route for pressurized air when system pressures exceed safe operating levels.
  • has a 1034 kPa (150 psi) internal relief valve.
  • is installed with the air compressor as a unit.
Air Spring
The 4WAS system has front and rear air springs. The air springs provide a varying spring rate proportional to the system's air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system's air. Increasing air pressure (compressing) raises the vehicle; decreasing air pressure (venting) lowers the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the 4WAS module command.
Air Lines and Fittings
NOTE: Apply a soapy water solution to the air lines to verify the location of air leaks. If the air lines are cut, ruptured or leaking, a service repair kit is available.
Nylon air lines with quick connect fittings connect to the air compressor and air spring solenoids. The compressor assembly output line is divided by the use of a fitting to supply the front and rear air springs. Fittings are also used to divide the air supply to the RH and LH air spring solenoids.
Air Suspension Height Sensors
There are two sensors used for the front suspension and one sensor used for the rear suspension. The sensors send a voltage signal to the 4WAS module. The output ranges from approximately 4.50 volts at minimum height (when the vehicle is low or in full jounce) to 0.50 volt at maximum height (when the vehicle is high or in full rebound). The sensors have a usable range of ± 45° compared to total suspension travel of 196 mm (7.84 in) at the front wheels and 240 mm (9.6 in) at the rear wheels. Therefore, the sensors are mounted to the suspension at a point where full suspension travel at the wheel is relative to the travel at the height sensor. The front height sensors are mounted to the frame and the links are attached to the upper arm ball studs. The rear height sensor is mounted to the frame and the link is attached to the rear lower arm ball stud.
When the height sensor indicates that the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the system. When the sensor indicates that the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the system to lower the vehicle to its trim height level.
Compressor Relay
A solid state relay is used in the air suspension system for compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the 4WAS module.
The compressor solid state relay is energized by the 4WAS module to have high current flow from the battery to the compressor motor.
4-Wheel Air Suspension (4WAS) Module
NOTE: The 4WAS module must receive a ride height adjustment calibration and must pass a pneumatic test when it is installed new or swapped.
The 4-wheel air suspension (4WAS) module controls the air compressor motor (through a solid state relay), all air spring solenoids, and provides power to front and rear height sensors. The 4WAS module also controls vehicle height adjustments by monitoring the three height sensors and other universal bus protocol (UBP) signals. The 4WAS module conducts all fail-safe and diagnostic strategies, and contains self-test and communication software for testing the vehicle and related components.

Jan 06, 2009 | 2003 Lincoln Navigator

1 Answer

Rear air ride suspension is not maintaining height


The are ride height adjusters the look like arms. they are mounted on the bottom of the struts and lower control arms that control the height The can be adjust but for the most part if the were working fine before then they need to be replaced. Make sure that there are no leaks in the system.

Dec 29, 2008 | 1997 Lincoln Continental

1 Answer

280zx rear hatch light switch


check behind both the latch and the lock sounds like out of adjustment a door adjustment may even fix it

Jun 03, 2008 | 1983 Nissan 280ZX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13614 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...