Question about Cars & Trucks

1 Answer

I can not pull up my ballance? - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 502 Answers

So this is a question? It is more like a statement. Key word ballance........not so car related...by itself anyway.

Posted on Dec 30, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 ford van E 150 will crank over but not start. has compreseion and fuel and spark and timing is on. What else could be issue


Pull a plug wire, stick a screw driver in the plug wire socket and hold the metal shaft of the screw driver about 1/8 inch from the block. Get someone to turn the ignition key to start and while it is cranking see if you get a spark. If not, look under the front of the truck and locate the "crank trigger" located on the front of the block and going to the area of the crank ballancer. If it looks dirty, the get some contact cleaner and squirt it good and use a tooth brush to clean the trigger and surrounding area of the ballancer where the trigger makes contact, then try starting again.

Dec 15, 2014 | Ford Cars & Trucks

2 Answers

How do I pull the harmonic ballancer and replace it on a 1999 olds alero?


You would need to use a puller. Looks like a chicken foot on steroids.

May 02, 2014 | Oldsmobile Alero Cars & Trucks

1 Answer

Machine keeps spinning out of ballance


wrong balancer attachment some might seem to fit
try one smaller or one bigger this should put back in balance

Nov 09, 2013 | Cars & Trucks

1 Answer

What does the timming balancer belt do on a 91 accord lx 2.2


The Ballancer Belt runs the ballancer shaft which was installed in the motor from factory to help offset vibrations in the motor or counter ballance for the engine to run smoother

Nov 20, 2010 | 1991 Honda Accord

1 Answer

Harmonic ballancer moves forward with throttle


That is not good. They are rubber mounted for vibration, over tightening the belts will pull it apart, it takes years, but they do fail. They cost about $100, and are not easy to replace. You need a big pulley puller and a big breaker bar with a socket for the crank shaft bolt. Hope this helps.

May 15, 2010 | 1999 Dodge Durango

1 Answer

I have had the bushes and arms done on my e46


Check and ELIMINATE the Possible Problem With WHEEL BALLANCING on SAID AXEL. Sounds as if A Wheel is Not Ballanced Properly. This Is Assuming that your Wheel "BEARINGS are GOOD.

Oct 31, 2009 | 1999 BMW 328 Series

1 Answer

The car jutters when driving over 60km/hr


Posible problems , listed from cheapest to most expensive.

Tires out of ballance
Broken chord in a tire
Bent rim
Loose ( worn ) tie rod ends
Bent axle
Wheel bearings ( but not likely)

If you have the tools , and a good safe flat driveway , jack up 1 corner of the car , spin the tire by hand and watch if it spins true , or wobles. while your at it , firmly grab the tire , and try to wiggle it side to side , in and out , back and forth. Repeat process for each wheel. If everything seems ok , I would think about getting tires ballanced. Probly about $ 12 each.
General observation is that if you feel the shake in the steering wheel , front tires are the problem , If you feel it on your bottom , rear tires. Good luck with that.
If you want to skip the whole jacking up the car proceedure , go directly to the wheel ballancing , and ask the mechanic to keep an eye out for "wheel out of true" while they spin on the ballancer.

May 09, 2009 | Suzuki Grand Vitara Cars & Trucks

1 Answer

Harmonic ballancer install


you have to use a balancer installer pain in the you know where but that has been the only way i have gotten the to work , do not beat them on you will not like what happens good luck kdc744

Jan 03, 2009 | 2005 Ford Mustang

1 Answer

Removing harmonic balancer on 96 regal 3.8


YES YOU DO HAVE TO HAVE A SPECIAL ADAPTER FOR THE NORMAL BALLANCER PULLER. NAPA HAS THE TOOL AND THE # IS BK700-2461. ONCE AGAIN THE ADAPTER IS USED WITH THE BALLANCER PULLER YOU ALREADY HAD. YOU HAVE TO SCREW THE EXTENSIONS INTO THE BALLANCER AND INSERT ANOTHER EXTENSION INTO THE CRANKSHAFT TO GET THE OLD ONE OFF. WHY G.M. DID THAT TO US IS STILL A MYSTERY.

Aug 01, 2008 | 1996 Buick Regal Olympic Gold

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...