Question about Cars & Trucks

Open Question

I can not get to the place to get my card bal.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm trying to remove a harmonic balancer. I've got to the point of taking it off. The pulley remover is placed. But the bolt when completely down only turns the balancer. How to fix please


Are you using a gear puller or an actual harmonic bal. puller? You can use air tools(carefully), or to hold the balancer/pulley still, use a chain wrench with an old belt wrapped around to prevent damage. I would not recommend a 2 or 3 jaw type gear puller.

Oct 17, 2015 | 1996 Buick LeSabre

1 Answer

Hi, Can't stop pully from moving when attempting to loosen bolt harmonic bal on 1993 old royale. Tried locking onto pully with vice grips; they fail to stop it from turning. Thanks....


use a chain and twist it around the pulley then twist the ends together put a bolt through both ends and fasten it to the block this will hold it in place once you take the slack out of the chain when taking the bolts out.

Sep 22, 2011 | 1989 Oldsmobile Delta 88

1 Answer

At 50mph it atartas shaking i bought new tire, new brakes been bal,new rotors new calabers any one have a clue? 2003 jeep wrangler


have some one remove the drive shaft and check the u-joints, sounds like you have one going bad.

Mar 12, 2011 | 2003 Jeep Wrangler

1 Answer

1930 Ford Model A coupe Tighten steering


change the bal joints... its not the matter of tightening the bolt..

Aug 01, 2010 | 2002 Ford ZX2

1 Answer

Have 06 f150 have avibration while driving down


Two things to look for, one is the drive shaft u joints, and drive shaft timing. all the u-joints should line up. Next check for a bent/ damaged wheel. I had to swap mine one wheel at the time with a known good wheel till I found the bad wheel that a bal. did not find.

Mar 20, 2010 | 2006 Ford F-150

1 Answer

1995 grand am 3100v6 replaced modual,cam sensor behind harmonic bal,and plugs still no spark whatnext


your module that the coil pack bolt too was your problem in the begining

Jan 14, 2010 | 1997 Buick Skylark

1 Answer

2007 ford expedition el has a vibration


are the king pins worn .check all ball joints tie rod ends ect . 1 mm movement = up to 5 mm wheel alighn play ..also check shockies

Jun 13, 2009 | 2007 Ford Expedition EL XLT

1 Answer

1998 dodge ram 1500 pick up (not 4wd)


easier on lift if not ramps on ground chalk wheel use stands once all belts are off remove center bolt on bottom crank pulley install crank pulley remover you may have to remove outer part of split pulley thread three puller bolts into bal there should be holes for this snug all three tight install adapter into center where main bolt came out thread tool against adapter as you tighten in the bal pulls out once out replace timing case seal at bottom of cover lightly apply grease or lithium on inside of seal put new bal alighn on keyway install reinstall tool slowly with air ratchet or impact gun reinstall slowly the grease on seal will stop seal from dry start up once bal all the way in install center bolt outer pulley if taken off belts etc

Aug 24, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...