Question about Toyota Cars & Trucks

Open Question

Need torque settings for toyota 2E engine 2000model

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Benimur
  • 6966 Answers

SOURCE: toyota 2e engine

Hi,

The only positive way to check if the oil pump is working and therefore there is correct oil pressure is to temporary install a non-electrical oil pressure gauge that uses a small copper tubing to sample the oil/pressure and drive a needle on the gauge. Depending on temperature, idle should register about 20+psi. Having done this and confirmed that indeed there is sufficient oil pressure then it may simply be a defective oil sending unit. Otherwise, no or low oil pressure at idle is an indicator that the engine needs to be opened up again.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.


Posted on Jul 24, 2008

Ad
  • 1779 Answers

SOURCE: need torque settings for 1985 4A corolla cylinder head

hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Posted on Jan 14, 2009

joecoolvette
  • 5660 Answers

SOURCE: need the cylinder head torque settings on a toyota

Tighten in several passes to 44 foot pounds.

I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.

Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.

Tightening torque pattern is as follows:

1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.

The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.

Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)

Posted on Jul 25, 2009

  • 2 Answers

SOURCE: 1986 toyota corolla 2E engine high fuel consumption

why does my normal rpm always bug down when the engine start?and when I started to use the air con, the rpm was playing. It doesnt go on a certain point. it always range at 800rpm then it will down to 700. what am I might do to solve this probem?

Posted on Mar 13, 2010

steve_e_uk
  • 1675 Answers

SOURCE: whats the torque setting for big end bearing bolt

hi big end bearings are two stage, 25nm leave ten mins, then 49nm cylinder head bolts three stages 20nm leave ten mins, 40nm leave ten mins then 60nm check after 5,000miles hope this helps

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many intake valves does a toyota tazz 2e engine 2004 model have


earlier 2Es have one inlet one exhaust
after the east west front wheel drive were introduced
most 2E toyota engines have three valves per cyl
two inlets and one exhaust

if you need the correct information on your 2004 2e engine
,,,,undo the rocker cover

e397a648-22cf-4373-b847-0ca46d719837.jpg

Jun 28, 2016 | Toyota Cars & Trucks

1 Answer

Torque setting specs for toyota 1.3 2e engine.


This will be in your shop manual, and if you are doing work that requires torquing the head bolts you really should buy a cheap shop manual.

Apr 27, 2016 | Toyota Cars & Trucks

1 Answer

Torque specification


petrol engine alloy head 65lbs
main bearing caps 80lbs
big end bolts 40lbs

Nov 21, 2013 | Cars & Trucks

1 Answer

Torque settings clio 1.5 dci big end shells


whats the torque setting for big end bearing bolt and cylinder head bolt for toyota corolla 12 valve 2E,1990.

Jan 12, 2010 | 2000 Renault 181

1 Answer

4 and 5 speed tranny for corolla 2e


When looking for a "faster" transmission you need to check the actual individual gear ratios of each gearbox and match anticipated rpm to available peak torque of the engine. This gets a bit complicated but likely if you speak with anyone who drag races a similar vehicle they can hook you up with charts & formulas. As far as top speed goes, that's all determined by your engine and differential/tire combination as all units are 1:1 in fourth gear (fifth gear is overdrive and may give you slightly more top end) For a street car, there are far easier ways of wringing out a bit more performance.

Mar 25, 2009 | 1992 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...