Question about Cars & Trucks

1 Answer

1998 Grand Cherokee 5.2 Engine will not start I have codes P00320,P1388,P0113,P0138,P1762,P0308

It has been running good, she washed it on the way home and ran fine the rest of the way home. The next morning it would not start. Hooked my Genesis to it and these are the codes. HELP! Relays and Fuses are good.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 29 Answers

Crankshaft position sensor

Posted on Dec 30, 2016

Testimonial: "Thank You Tom I am ordering one now."

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: 1999 dodge dakota p1762 code

dont know lots about this witout engine size but some have 1 coil per cylender possible coil is bad or plug 02 sensor will cause some problems but a miss fire will cause it to run like trash

Posted on Oct 08, 2008

emissionwiz
  • 75822 Answers

SOURCE: 98 PLYMOUTH GRAND VOYAGER WONT START - BLOWS ENG FUSE - HELP

You have a shorted engine harness, this is not common but it does happen, heat and engine movement cause damage to the harness, this is most common on hi miler cars and vans, the only way to fix it is to start by looking anywhere the harness rubs, that is where the damage occurs.

Posted on Oct 20, 2008

jmeyer847
  • 185 Answers

SOURCE: check engien lihgt with code p1762

CEL Code P1762 is Governor Pressure Sensor Offset Improper Voltage. Make sure all your wires going to the sensor are ok, then if they are I would look into a new Sensor. Hope this gives you some direction. Thanks for Using FixYa!

Sincerely,

JC

Posted on Nov 30, 2008

  • 1118 Answers

SOURCE: engine turns over fine , car will not start.

well the first part of your question i was all ready to tell you to put a new fuel pump in, now not so sure, there is a relay for fuel pump, can you hear pump cycle and relay click? relay under hood you will have to listen close they don't run long maybe a couple secounds, if you don't relay bad. if you do pump could be bad, do fuel pressure test pump could be weak. don't think sunroof and turn signals are related, but stranger things have happend.

Posted on Jan 25, 2009

  • 50 Answers

SOURCE: 93 Jeep Grand Cherokee Won't start

The crankshaft position sensor was seriously problematic in those old jeeps. It's located towards the top of the bell housing slightly to the driver's side I think.

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Codes p0203, p0123, and p0113 are showing for my 2001 jeep grand cherokee. The voltage from the tps plug was 1.5v


P0113 intake air temp voltage too high
P0123 Throttle position sensor voltage too high
P0203 is injector #3 control circuit
voltage is higher that 4.9 volts short to 5 volt supply circuit

erase the codes and drive vehicle to see if the codes come back if they do you have a hard code check the supply circuit for a short

Nov 11, 2013 | 2001 Jeep Grand Cherokee

1 Answer

Engine misfiring, warning lights are coming in and out.digital dash trac control, overdrive off light,temp gauge shots up momentarily, and check engine light. car running rough. 2000 Grand Marquis 95k


Misfire condition on cylinder 5 (P0305) and cylinder 8 (P0308). There is a good explanation of it here :
http://troubleshootmyvehicle.com/ford/4.6L-5.4L/how-to-diagnose-misfire-codes-1

Mar 20, 2013 | 2000 Mercury Grand Marquis

1 Answer

Code p1762 govenor pressue sensor offset volts


P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Dec 14, 2010 | 2001 Jeep Grand Cherokee

2 Answers

1998 Jeep Grand Cherokee Laredo 4.oL I got a code po113


Trouble Code: P0113 (4.0L L6 VIN S Auto)
IAT Sensor Circuit High Input Print this code dataprint_icon_codes.gif Number of Trips to Set Code: 1
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
Check with ignition on or engine running; battery voltage more than 10v; The PCM detected the IAT Sensor input was over 4.90v (exc. Dakota, Durango, Ram) or 4.98v (Dakota, Durango, Ram) for 3 seconds.

Possible Causes:
  • IAT Sensor signal circuit shorted to VREF (5v)
  • IAT Sensor signal circuit is open, or the ground circuit is open
  • IAT Sensor is damaged or it has failed (an internal open circuit)
  • PCM has failed


d1eaead.gif

Dec 01, 2009 | 1998 Jeep Grand Cherokee

2 Answers

Diagnostics "P1762 Manufac. Contrl. Transmission"


Had the same code on my 2002 Jeep Grand Cherokee. Started having shifting problems as well. Code is for governor pressure sensor on trans. Cost me about $800 for dealer to fix. No problems after part changed out.

May 22, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Code p1762 is appearing on my jeep dashborad


Governor Pressure Sensor Offset Volts Too Low or High

Mar 22, 2009 | 2004 Jeep Grand Cherokee

1 Answer

2001 jeep grand cherokee transmission revving-codes p1757, p1762


P1757 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Above 3 PSI In Gear At 0 MPH Conditions: Engine started; vehicle driven to a speed over 30 mph, and the PCM detected the Governor Pressure Sensor was more than 3 psi with the requested pressure at 0 psi (95% duty cycle command) for 2.65 seconds. The fault must occur twice on one trip to set the code. Possible Causes: Check for the presence of other A/T related trouble codes Governor pressure Sensor is damaged or has failed Governor pressure Sensor VREF (5v) circuit is open or shorted Transmission valve body is leaking, damaged or has failed PCM has failed P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Nov 17, 2008 | 2001 Jeep Grand Cherokee

1 Answer

1999 dodge dakota p1762 code


dont know lots about this witout engine size but some have 1 coil per cylender possible coil is bad or plug 02 sensor will cause some problems but a miss fire will cause it to run like trash

Oct 08, 2008 | 1999 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...