Question about 1983 Chevrolet Chevy

1 Answer

1975 chevy c-20 truck power steering mounts

I need a diagram showing the power steering mounting brackets on a 1975 chevy c-20 truck can anyone please help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,674 Answers

This is for 5.7L engine, hope that's yours.1975 chevy c-20 truck power steering mounts - 34cefcc.jpg

Posted on Jul 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a power steering mounting diagram for a 1981 chevy caprice


The pump will bolt to the bracket, then you will have two bracket bolts to the water pump and another bracket bolt to a bracket attached to one of the exhaust manifold bolts.

Dec 04, 2015 | Cars & Trucks

1 Answer

I need to remove the front engine mount and bracket to get to the power steering pump bolts. Can you PLEASE help me.


remove the nuts holding the mounts .jack up the engine .or better to hire an engine lift.

Dec 14, 2013 | Toyota Yaris Cars & Trucks

1 Answer

How to change a crank position sensor on 2006 suzuki forenza


5) Install the rear A/C mountingbracket. Tighten the rear A/C mounting bracket bolts to 35 Nm (26lb-ft).6) Install the A/C compressor. 7) Install the power steering pump. 8) Connect the negative battery cable.12_16_2011_6_00_05_pm.jpg
If this helps, please say so! Thanks! :-)

Dec 08, 2011 | 2006 Suzuki Forenza

1 Answer

I need a diagram of the bracket positions & mounting of the Power Steering pump for a 1989 Dodge Dakota 2wd - 4cylinder 2.5


Yes there is complete guide available for power steering pump and bracket positions mounting.Its will all details and diagram and lot more details.Please click on link below.Check the details http://technoanswers.blogspot.com/2011/03/1989-dodge-dakota-2wd-4cylinder-25.html ------------------ In this link is complete guide for steering and suspension of 1989 Dodge Dakota 2wd - 4cylinder 2.5------------------ This should help. Thanks.Helpmech.

Mar 29, 2011 | 1989 Dodge Dakota 2WD

1 Answer

Serptine belt diagram


q4073a.gif



Belt Installation, Aerostar 4.0L Engine


q1815e.gif


Item Part Number Description 1 8620 Drive Belt 2 N606068 Bolt 3 10300 Generator 4 10153 Generator Mounting Bracket 5 8509 Water Pump Pulley 6 6B209 Drive Belt Tensioner 7 N800199 Screw 8 8678 Belt Idler Pulley 9 N802096 Screw 10 19703 A/C Compressor 11 2882 A/C Compressor Mounting Bracket 12 3C718 Brace 13 N806020 Bolt 14 3A674 Power Steering Pump 15 3A733 Power Steering Pump Pulley 16 N800199 Screw 17 N606572 Bolt 18 N620481 Nut 19 8501 Water Pump 20 6312 Crankshaft Pulley A - Belt Tension Check (See Specifications) B - Tighten to 40-55 Nm
(30-41 Lb-Ft) C - Tighten to 24-30 Nm
(18-23 Lb-Ft) D - Tighten to 21-29 Nm
(15-21 Lb-Ft) E - Tighten to 40-50 Nm
(30-37 Lb-Ft)

Belt Installation, Ranger and Explorer 4.0L Engine


q4082b.gif


Item Part Number Description 1 8620 Drive Belt 2 10300 Generator 3 8678 Belt Idler Pulley 4 19703 A/C Compressor 5 3A733 Power Steering Pump Pulley 6 8501 Water Pump 7 6312 Crankshaft Pulley 8 6B209 Drive Belt Tensioner 9 N806020 Bolt 10 2882 A/C Compressor Mounting Bracket 11 3A674 Power Steering Pump 12 N606572-S2 Bolt 13 N800199-S8M Bolt 14 N620481-S2 Nut 15 3C718 Brace 16 N606068 Bolt 17 10153 Generator Mounting Bracket 18 8509 Water Pump Pulley 19 N605805-S2 Bolt A - Belt Tension Check (See Specifications) B - Tighten to 21-29 Nm
(15-21 Lb-Ft) C - Tighten to 40-55 Nm
(30-41 Lb-Ft)

Belt Installation, Ranger 2.3L Engine


q3646c.gif


Item Part Number Description 1 8678 Belt Idler Pulley 2 10300 Generator 3 8509 Water Pump Pulley 4 3A733 Power Steering Pump Pulley 5 2E884 A/C Clutch Pulley 6 6312 Crankshaft Pulley

Belt Installation, Aerostar 3.0L Engine


q4740a.gif


Item Part Number Description 1 10300 Generator 2 3F671 Belt Idler Pulley 3 3A733 Power Steering Pump Pulley 4 6B209 Drive Belt Tensioner 5 6312 Crankshaft Pulley 6 8509 Water Pump Pulley 7 19703 A/C Compressor 2010&c18=modelyear&c35=wsm%2cdrive%20belt%20replacement%2cssk%2c03-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1995 Ford Aerostar

1 Answer

I WILL LIKE TO KNOW HOW CAN I REPLACE THE POWER STEERING PUMP ON A 2001 CHEVY MALIBU


1. Remove serpentine belt

2. loosen power steering pressure and return hoses

3. Remove nut from pressure line mounting on alternator bracket

4. remove power steering pump mounting bolts.

5. Lift pump assembly from engine mounting and remove hoses.

6. Reverse order to install. Fill and bleed system.

NOTE: A new or rebuilt power steering pump will most likely not come with a pulley attached. You will need a power steering pulley remover/installer tool to transfer the pully from the old pump to the new one.

Feb 19, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

Do you know how to install the power steering pump in 400 small block chevy?


POWER STEERING PUMPS FOR THE 400 AND 350 CHEVY ENGINES ARE HELD IN PLACE IN A BRACKET AND BRACE MOUTED TO THE ENGINE.CHECK AROUND ON LINE ON INTERNET LOOK UP POWER STEERING PUMP MOUNTING BRACKETS FOR 400 CHEVY ENGINE.YOU NEED THE MOUNTING BRACKET IN ORDER TO INSTALL POWER STEERING PUMP.

Feb 18, 2011 | Chevrolet El Camino Cars & Trucks

1 Answer

How do you replace the alternator on a 2000ford contour



Removal & Installation

2.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove the air cleaner-to-throttle body tube and the mass airflow sensor.
  4. Unplug the connectors and remove the cables from the alternator.
  5. Raise and support the vehicle.
  6. Release the drive belt tensioner and remove the drive belt from around the alternator.
    NOTE It is not necessary to remove the drive belt from the engine.
  7. Remove the alternator mounting bracket bolts and remove the mounting bracket.
  8. Lower the vehicle.
  9. Remove the power steering pressure hose bracket retaining nut and bolt and remove the bracket with the hose from the engine lifting eye.
  10. Remove the alternator mounting bolts and remove the alternator from the vehicle.
  11. To install:
    1. Place the alternator into position and install the mounting bolts finger tight.
    2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
    3. Raise and support the vehicle.
    4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
    5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
    6. Lower the vehicle.
    7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
    8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
    9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
    10. Connect the negative battery cable. To install:
      1. Place the alternator into position and install the mounting bolts finger tight.
      2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
      3. Raise and support the vehicle.
      4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
      5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
      6. Lower the vehicle.
      7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
      8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
      9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
      10. Connect the negative battery cable.


Sep 28, 2009 | 2000 Ford Contour

1 Answer

I broke timing belt when replacing hormonic balancer


Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Jun 28, 2009 | 1992 Honda Accord

1 Answer

Need the belt diagram for the water pump belt for a 95 Auroa


42161874BELT, REPLACE
  1. Release belt tension and remove belt from power steering and alternator pulleys. Twist belt to get between tensioner and front cover and between power steering pulley and engine mount bracket.
  2. Raise and support vehicle.
  3. Turn wheel to the extreme right and remove right side splash shield.
  4. Remove belt from crankshaft and A/C compressor pulleys. Twist belt to get between idler pulley and engine mount bracket.
  5. Lower vehicle.
  6. Twisting new belt to get past the front cover, install belt around power steering pump pulley, Fig. 15. Allow belt to hang free.
  7. Twist belt to get between tensioner and front cover, wrap belt around alternator.
  8. Remove belt from power steering pulley and set aside.
  9. Raise and support vehicle, then twist belt to get between tensioner and front cover, wrap belt around crankshaft and A/C compressor pulleys.
  10. Install right side splash shield and lower vehicle.
  11. Position belt around power steering pulley and release tensioner.

Nov 23, 2008 | 1995 Oldsmobile Aurora

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

795 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...