Question about Cars & Trucks

Open Question

Where do I put vapo pads in a v31000 - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pc75-1. How do I flush hydraulic system?


Lian LI PC-75 work log. {56k beware} ' Overclockers Forums

www.overclockers.com/.../523704-Lian-LI-PC-75-work-log-56k-beware
Aug 18, 2007 - 13 posts - ‎9 authors I will be using the Lian Li PC-75 for the watercooling build. ... After about 1/2 hour with a jigsaw and dremel the finished product. ... Vapo sides for me so that they will be 4 inches longer and fit flush with the Lian Li PC-75 ... Will go higher now that I am runningcooler but for the purpose of the tests this works ...

Oct 14, 2015 | Cars & Trucks

1 Answer

Where is the fuse located for cirrus vapo 02 steamer


There is a tiny reset buttom is located on the bottom next to the water jar. Try that first. It is usually green on our unit but I have seen it red before but possibly from another steamer.

Feb 06, 2012 | Cars & Trucks

1 Answer

Changing brake pads on my 2004 colorado two pads are labeled "A" and two pads are labled "B" do I put A pads on one side and b pads on the other or a inboard and b out board. Do the...


You will put an A and a B on both sides. Wear indicator points down. As for inside or out, match them to your old pads, there will be a difference in design. Most likely A goes inside.

Nov 01, 2010 | 2006 Chevrolet Colorado

4 Answers

Put new pads on my 05 ford excursion 4x4 and I cant get the caliper to go back on the rotor. there are 3 pcs involved, the rotor, the caliper, and a bracket that the caliper mounts to. first I put on the...


youll have to clamp the brake hose,undo the bleed screw,and push the piston[s] back in,then shut off bleed screw,undo clamp on hose,and try assembly again.bracket first,then pads into bracket,then slide caliper over pads,and then put bolts holding caliper back in ,with a bit of grease on the slides.

Jul 01, 2010 | 2005 Ford Excursion

2 Answers

My son thinks its a good idea to put gease on new pads (on th pad portion itself) when installing new pads. I know for several reasons its not a good idea. Is there something new I don't know about?


if is copper grease on outside the brake pad it is ok ,to stop the pad to seize up move free from cailper ,if he put grease inside the pads no not safe ,bad news

Nov 06, 2009 | 1996 GMC Yukon

1 Answer

I want to change brake pads on the front on my 03 Mazda Protege. There was a wire spring that came off when i removed the pads. I have not been able to find out why there is a spring and how to put it back...


it is to help push pads off of rotor after you let off brakes before yo insert pin put spring between pads rn pin inside loop then there should be holes in pads where end of sprin will sit so it doesnt tilt up or down

Aug 21, 2009 | 2003 Mazda Protege

1 Answer

2006 dodge ram 2500 4x4 diesel replace brake pads front and back


Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Apr 25, 2009 | 2004 Dodge Ram 2500

1 Answer

How do I remove the old front disk pads and replace them with new pads on a 1988 Mercury Grand Marquis? Marvin


remove the 2 bolts holding the caliper on.then remove caliper.remove pads.you may have to save clips on old pads.now dont let the caliper hang it may hurt the brake line tie it up.once pads are removed open the brake resivoir (where you put the brake fluid).now use a c-clamp to push in the caliper piston(the round part sticking out).once piston is all the way in put new pads on the caliper.don't force pads over roter.line up caliper with the bracket.put bots though the holes and tighten.do both sides and fill up the fluid put cap on.done.no bleeding required.

Mar 25, 2009 | 1988 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...