Question about Ford Thunderbird

Open Question

Were is the blend door actuator located in my '96 ford Thunderbird?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

Where is located blend door actuator on 2006 Ford E-350 passenger van


It's located on top of the evaporator case. There is a access cover on top of the dash on the passenger side.

Apr 10, 2016 | Ford Cars & Trucks

1 Answer

Where is the heater actuator located on a 2002 Ford expedition


02 Ford Explorer Heat Blend Door Actuator Simple Fix - No ...

? 3:17
www.youtube.com/watch?v=uvuPzf0wjEg
Apr 28, 2012 - Uploaded by broomballusba12 02 Ford Explorer Heat Blend Door Actuator Simple Fix - No Tools Needed ... I will be making a few new videos shortly on the Ford Explorer, The Ford Expedition, .... This does Not Work on a 2002Ford Explorer Eddie Bauer.

Aug 21, 2015 | Ford Cars & Trucks

2 Answers

My blows cold and I hear a clicking sound from the inside...what could it be?


There are electric motors that move blend doors in your dash board. The blend doors control the heat/cool ratios as well as the location the air will blow from. It's very common for the doors to break or the motor to fail and require replacement which can be costly.

Mar 16, 2015 | 2003 Ford Explorer

1 Answer

I'm trying to locate the blend door actuator on my


Google 2001 blend door replacement or actuator replacement
its not an easy job, I had to cut the duct work out to get at it
the videos are good

Oct 19, 2014 | Ford F-150 Cars & Trucks

1 Answer

Heating and defrost unit does not work but its getting power


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks) This is well documented problem on this make and model.

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Nov 08, 2012 | 1997 Ford Thunderbird LX

1 Answer

Heater stopped working. Got the car use about a month ago and it worked fine up till now.


Have the heater temperature control blend door actuator checked, that is the usual problem, the actuator moves the air temperature control door that moves back and forth to supply hot and cold air or a blend of the two air streams from the heater core and the AC evaporator core, I have changed out about a dozen of them for this problem of no heat, the actuator is located behind the glove box to the left on the air duct, it has a small electrical connector going to it, very hard to get at.

Dec 03, 2010 | 1994 Ford Thunderbird

1 Answer

How To Replace The Heater Core In A 1997 Ford Thunderbird LX


Heater Core Removal
  1. Partially drain the cooling system.
  1. Remove the tube gasket from the heater core tubes.
  1. Remove four heater core access cover retaining screws and remove the access cover from the A/C evaporator housing (19850).
  1. Remove A/C electronic blend door actuator.
  1. Slide heater core (18476) and seals from the A/C evaporator housing.
Installation
  1. Install the heater core in the A/C evaporator housing with the tube gasket on the outside of the case.
  1. Install A/C electronic blend door actuator as described.
  1. Position the heater core cover on the A/C evaporator housing. Install the four retaining screws.
  1. Refill the cooling system.


    1a302ce.gif




    Item Part Number Description 1 18596 Heater Core Tube Gasket 2 18476 Heater Core 3 18B300 Heater Core Cover 4 390747-S2 Screw (4 Req'd) 5 18N267 Heater Core Cover Seal


    Hope this helps... Cobra

Jun 12, 2010 | 1997 Ford Thunderbird LX

1 Answer

Cant find the blend door actuator on 2003 ford f150 super crew


The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Jun 21, 2009 | 2003 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...