Question about Cars & Trucks

Open Question

Car started after a long period non use .key removed .when reinserted would not turn

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: 2003 Prius sometimes will not start, engine light comes on. Removing key from ignition, reinserting key, & turning wheel till it locks will then allow the car to start. Engine light stays on for a

I had a wire connector on the front of the engine that had so much tension, the wires broke. I didn't notice until a wet day when the car wouldn't start (and the Check Engine light was on). (The error code was related to an Emissions error.) The connector is located on the engine, front, just left of center. Hope this helps!

Posted on Jan 12, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the emobilizer and key have to be replaced if the wrong key was put in ignition and had to be pulled and wiggled pretty hard to remove now it wont start


When you turn the ignition switch to ON(II), the immobilizer system indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK(0), remove the key, reinsert it, and turn the switch to ON(II) again.If the system repeatedly does not recognize the coding of your key will need a repair.

Dec 03, 2015 | 2000 Acura Integra

1 Answer

Kia 2005 Amanti: Electronics go black and reset to 12:00 and Jan 1. Removing key and trying again in neutral or with open driver door sometimes works and other times doesn't.


cud hav computer or module issues--a readout scan shud b done-it shows voltages that a tech can decyfer------try using anothr key-chip cud b worn---------or disconnect batt a few --------or pull plug on computer and clean it-pins get dirty-----may reboot to normal--------go to a private shop for scan-not a dealer

Dec 11, 2013 | 2005 Kia Amanti

1 Answer

My renault clio doesnt start but turns over and then i leave the ignition on and take a relay out and knock it a few times out it back then it starts.this happenes everyday.


wiring connector going to injection unit on right side of engine disconnect it clean terminals with screwdriver and sand paper wet and dry preferabely once this is done spray connectors ,reconnect it and joddle the all other electrical connections on engine spray all with wd40 once this is done the car will start you could try starting car after each connection worked on common fault on these cars also if its a immobiliser fault reset sequence as follows remove key from ign lock up car holding key in locked position count to 30 seconds then unlock car,put key in the ignition to third position( ie key position before starter is engaged) wait 20 seconds then remove key reinsert and car will start if not go through sequence again

Mar 20, 2013 | 2002 Renault Clio

1 Answer

Car won't start , said it was disabled for


THe key has a code in it that is read by the engine immobiliser. BY removing the key and reinserting you are giving the immobiliser a chance to read the code again. Give it a try. THe battery in your key may be getting low and needs replacing.

Feb 25, 2013 | Cars & Trucks

1 Answer

I had a new key cut for my 2004 accord and replaced the keyless entry pad. The car will not start...does the pad need reprogramed to start the car


If you car has the immobilizer system, the following might help.

The Immobilizer System protects your car from theft. A properly coded ignition key must be used in the ignition switch for the engine to start. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key.
Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.

Hope this is helpful to you.

Jan 23, 2010 | 2004 Honda Accord

2 Answers

Had a flat battery on a4 when i put new batt on the alarm wont go off or central lockin is not working


disconnect the ground cable only on the batter for two minutes, be sure the key is not in the ignition, reconnect cable, turn key to on, then turn off. remove the key, reinsert it and crank the car .

Dec 31, 2009 | 2001 Audi A4

1 Answer

How do I reset the anti-theft system on my 2000 Pontiac Bonneville?


disconnect the negative battery cable for about three minutes, replace, put key in ignition and turn it on, DO NOT START CAR, turn it off, remove key, reinsert key and start car

Dec 17, 2009 | 1998 Pontiac Bonneville

1 Answer

My grand am won't start the secruity light is on


TRY THE RELEARN PROCEDURE.....INSERT KEY IN IGNITION, AND TURN TO THE RUN POSITION,,DO NOT CRANK THE ENGINE..LET CAR SET WITH KEY ON FOR TEN MINUTES.. THEN TURN KEY OFF AND THEN BACK ON FOR ANOTHER TEN MINUTES... AGAIN TURN OFF THEN BACK ON FOR THE LAST TEN MINUTES... AFTER TIME IS UP TURN OFF REMOVE KEY AND REINSERT AND ATTEMPT TO START CAR.. IF STILL NO GOOD TRY A SPARE KEY IF YOU HAVE ONE IF STILL NO GOOD TAKE YOUR KEY TO DEALER FOR REPRORAMMING

Oct 10, 2009 | 2005 Pontiac Grand Am

1 Answer

Having a challenge programming a 1999 Lexus RX 300 newly cut key.


did the lock smith cut key with resister in in maybee not gotta go to dealer get one cut then put old key in start car then turn of remove key put new key in turn on till security light goes out then start car

Aug 29, 2009 | 1999 Lexus RX 300

1 Answer

2003 Prius sometimes will not start, engine light comes on. Removing key from ignition, reinserting key, & turning wheel till it locks will then allow the car to start. Engine light stays on for a


I had a wire connector on the front of the engine that had so much tension, the wires broke. I didn't notice until a wet day when the car wouldn't start (and the Check Engine light was on). (The error code was related to an Emissions error.) The connector is located on the engine, front, just left of center. Hope this helps!

May 25, 2009 | 2002 Toyota Prius

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...