Question about Cars & Trucks

Open Question

Hi that torque setting I am looking for is for the cylinder head bolts on v w 14i mk1 2007 golf & yes the bolts are new

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 97 Answers

SOURCE: hi looking for torque settings for cylinder head bolts on v w golf 14i 2007

are not the bolts to be replaced with new ones as they could have stretched ?????

Posted on Dec 28, 2016

Testimonial: "hi did you read the question not asking if I must replace the bolts I am looking for the torque settings if you can help would be much appreciated"

Ad
jamessizer81
  • 7515 Answers

SOURCE: hi its the torque settings for the cylinder head I am looking for on v w 14i 8 valve mk1 2007 golf

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Posted on Dec 29, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi its the torque settings for the cylinder head I am looking for on v w 14i 8 valve mk1 2007 golf


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Dec 29, 2016 | 2007 Volkswagen Golf

1 Answer

Hi looking for torque settings for cylinder head bolts on v w golf 14i 2007


are not the bolts to be replaced with new ones as they could have stretched ?????

Dec 28, 2016 | 2007 Volkswagen Golf

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

TORQUE SETTINGS FOR 1.4 16V 04 VAG ENGINE THEY USED IN SEAT LEON 04 16V 1.4.


Cylinder head instructions

Tightening sequence
tdisline_536.jpg
Cylinder head torque setting for 2004 VW 1.4L 16V fitted in Seat Leon
Renew bolts

Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

May 17, 2011 | 2000 Volkswagen Golf

1 Answer

What is the cyl head torque setting for 05 vw golf 1.4 fsi 16v


Cylinder head instructions

tdisline_358.jpg
Cylinder head torque setting for 2005 VW Golf 1.4 FSI
Renew bolts
Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

Mar 23, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    1 Answer

    Hi, I`m looking for the torque settings for the cylinder head on an audi a4 1.8 1997 petrol


    Cylinder head instructions for Audi A4 1.8 (1997)

    Tightening sequence:

    9c9e892.jpg
    Renew cylinder head bolts: Yes
    Stage 1 - Tighten: 40 Nm

    Stage 2 - Tighten: 60 Nm
    Stage 3 - Tighten: 90 degrees
    Stage 4 - Tighten: 90 degrees

    Sep 21, 2010 | 1998 Audi A4

    1 Answer

    Hi, I`m looking for the torque settings for the cylinder head on an audi a4 1.6 1998.


    Cylinder head instructions for Audi A4 1.6 (1998)

    Tightening sequence:

    6432434.jpg
    Renew cylinder head bolts: Yes
    Stage 1 - Tighten: 40 Nm
    Stage 2 - Tighten: 90 degrees
    Stage 3 - Tighten: 90 degrees

    Sep 17, 2010 | 1998 Audi A4

    2 Answers

    Golf iv 1.6 8v cylinder head torque settings


    hi to tighten you have to do it in 4 stages as follows
    1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
    10 4 2 6 8 front of engine back of engine 7 5 1 3 9

    in that order hope this helps

    May 10, 2010 | 1986 Volkswagen Golf

    2 Answers

    Flywheel bolts torque settings


    Check with your local auto parts store. Or buy a repair manual

    Jun 07, 2008 | 1999 Volkswagen Golf

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    79865 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    john h

    Level 3 Expert

    14398 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...