Question about 1999 Honda Civic

Open Question

Crank swhat is torque and seconce 1999 honda civic 1.6. Lxhaft bearing cap torque anf seconce

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Replacing head gasket on 1995 honda civic, require torque specs and secquence

wow. a lot of bad information on this site. Refer to a manual for the proper torque sequence. The civic I believe is a two step torque procedure. First 22 ft lbs, than 53 ft lbs.

Posted on Jan 01, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

SOURCE: Torque specs for 96 Honda Accord 2.2L

the main bearings bolts is to 1st step 30Nm or 22lbs ft and the last step is 75Nm or 54lbs ft in this tighten secuence. 9 3 1 5 7 on the top bolts and........ ........ ........ ... 8 6 2 4 10 botton bolts and the connecting rod 45Nm or 34 lbs ft i hope be help you

Posted on Nov 09, 2009

  • 98 Answers

SOURCE: Need torque specs for the main bearings/caps/diagram for head.

main caps 80 ft. lbs.b52beae.gif

Posted on Nov 11, 2009

walleyracing
  • 76 Answers

SOURCE: hi what is the head torque on a 2002 honda civic

Dont forget to apply clean engine oil to the threads of each bolt for proper torquing. Then finger tighten. Then

    1. Tighten the cylinder head bolts to their final torque specification in 4 steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows: Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).


  • Posted on May 03, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    2 Answers

    Why doesn't this 2000 Honda civic lx turn over when everything else works inside the car?


    Honda Civic Coupe Questions - car will not start. battery ok ...

    www.cargurus.com > Questions > Honda > Civic Coupe

    CarGurusJul 9, 2008 - Get someone to turn it over and see if it is getting spark. ... i have the same issue with my 1993 civic lx it has a 1.5 sohc non-vtec i changed ... comes wen the 2nd click of the main relay it doesn't occurs until after few minutes, few .... My 2000 Honda Civic Ex Vtec will not start, has a new tps, new throttle body, ...

    Part 1 -How to Troubleshoot a No Start (1.6L Honda Civic)

    troubleshootmyvehicle.com > Honda > 1.6L
    Dec 31, 2012 - Difference Between a No Start and a No Crank Condition. ... can cause your 1.6L Honda Civic (Civic del Sol) to Crank but Not Start. ... In other words, the engine doesn't turn over at all. ... 1995, 1996, 1997, 1998, 1999, 2000.

    98 Honda civic won't crank (PushStart) - YouTube

    ? 4:11
    https://www.youtube.com/watch?v=X5W7OqjKB8I
    Oct 21, 2013 - Uploaded by SkzDaniel
    Honda Civic won't start or crank with the clutch but goes on when you push start it. ... 2000 Honda Civic LX with new battery and starter. Still will ...

    2000 Honda Civic LX with new battery and starter. Still will ...

    ? 6:34
    https://www.youtube.com/watch?v=p7KAO__nM1s
    Aug 21, 2013 - Uploaded by Robert SnyperMD
    2000 Honda Civic LX with new battery and starter. Still will not start. ... Crank, No Start Diagnosis Honda Coil test. - Duration: 11:17. by ...

    Jan 05, 2016 | Honda Cars & Trucks

    1 Answer

    I am trying to find out the torque spec for a 1999 honda accord 3.2 vtec connecting rod and main bearing


    From Helms manual (factory shop manual)
    Rod, FI engine: 34 lbs
    Rod, Carb engine: 23 lbs
    (I use blue thread locker on rod caps)


    Crank caps: 51 lbs. (oil threads and under bolt head)

    Mar 05, 2015 | 1999 Honda Accord

    1 Answer

    Hi i need torque settings for a honda ballade 1983 model 1.5 12valve ew2 motor


    Main bearing stage 1: 25NM, stage 2: 50NM
    Big-end bearing stage 1: 14NM, stage 2: 28NM
    Cylinder head stage 1: 30NM, stage 2: 60NM

    Sep 27, 2014 | Honda Accord Cars & Trucks

    1 Answer

    Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


    CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

    Mar 02, 2011 | 1989 Honda Civic

    1 Answer

    My 94 honda civic crankshaft snaped off because someone spotwelded the bolt on the pully and the pully fell off due to the crankshaft breaking how do i replace the crankshaft


    Motor has to come out and be disassembled. Pull engine, drop oil pan, undo main bearing cap, rod bearings, undo connecting rods and slide crank out. Unless you have tools (and lots of them including engine hoist, you ought to have a reputable shop do the work.

    Jan 07, 2011 | 1994 Honda Civic

    1 Answer

    What is the torque rear end bearing cap on a 1500 1999 chevy


    Main Bearing Cap Bolt

    4.3L
    Step 1 15 (20)
    Step 2 Additional 73 Degrees

    5.0L & 5.7L
    2-Bolt Main 77 (105)
    4-Bolt Main Inner 77 (105)
    4-Bolt Main Outer 67 (90)

    4.8L, 5.3L and 6.0L
    Main Bearing Cap Bolt/Stud


    Inner
    Step 1 15 (20)
    Step 2 Additional 80 Degrees

    Side 18 (25)

    Outer (Stud)
    Step 1 15 (20)
    Step 2 Additional 53 Degrees

    Jan 07, 2010 | 1999 Chevrolet Silverado 1500

    2 Answers

    99 dodge intrepid specs


    Inner main bearing cap bolts:
    Torque to 15 ft-lbs, then rotate an additional 1/4 turn

    Outer main (windage tray) bearing cap bolts:
    Torque to 20 ft-lbs, then rotate an additional 1/4 turn

    Main bearing cap cross bolts:
    Torque to 250 in-lbs or 20.83 ft-lbs

    Connecting road bearing cap nuts:
    Torque to 20 ft-lbs, then rotate an additional 1/4 turn

    Apr 21, 2009 | 1999 Dodge Intrepid

    1 Answer

    1999 honda civic ex (automatic) studdering/missing when driving


    Could be crank shaft sensor and cam sensor, try crank first.

    Apr 08, 2017 | 1999 Honda Civic

    1 Answer

    1987 NTC300 CUMMINS


    All main caps cannot be torqued until all are in place finger tight. A bolt small enough to fit in the oiling hole in the crank can be ground down to help roll bearing in place, just rotate crank. I thought the thrust bearing was in #6 but its been a while. Also look for chaffing at cap/block surface. Thousands of miles will cause chaffing at #6 or 7 mateing points. If you cannot see the mfg's grinding markes you have less clearance than before. Unless you replace the block you need to put the old bearings back in for those caps. Good luck...

    Sep 18, 2008 | 1999 Ford Super Duty F 450

    Not finding what you are looking for?
    1999 Honda Civic Logo

    Related Topics:

    23 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...