Question about Cars & Trucks

1 Answer

Where can i find the reset button to reset all the sensors and make my car to start.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 50,022 Answers

No such button
run the fault codes to find which sensor is faulty and fix it

Posted on Dec 29, 2016

Testimonial: "thankyu"

  • Ali Pupun
    Ali Pupun Dec 29, 2016

    i have fixed all faulty sensors already but the check light is still showing and the car wont start what shall i do?

  • Bill Boyd Dec 29, 2016

    pull the oil filler cap and see if the rockers move while cranking--could be a broken timing belt or chain
    can you post all the fault codes you found and what sensors you fixed



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there a fuel reset button on a 1996 Subaru Impreza my car shut off now will not start it turns over we have change the camshaft sensor the crankshaft sensor spark plugs and it's still just turns over

No reset button. Ford is the only one that uses them.

have you checked for spark? Have you checked fuel pressure?

i would assume that you checked for spark and found none since you replaced the crank sensor which provides information for both spark and injector pulse.

Where the plugs wet with gas when you pulled them out?

Mar 06, 2015 | Subaru Cars & Trucks

2 Answers

How to reset oil light

When you open the drivers door there is a fuse box on the dash where it meets the door. Pull off the cover and there will be a red reset button. Turn the car on but do not start it. Once the power is on tap the reset button until the chane oil light is flashing, the hold it down until it goes off. This is how you also reset the check tire pressure light.

Jun 14, 2014 | 1999 Pontiac Grand Am GT

1 Answer

01 f150 4.2 will turn over but wont start

Check Inertia sensor. This cuts off power to fuelpump. It has a reset button and is usually behind the front floor kickpanels.

Feb 27, 2014 | Ford Cars & Trucks

2 Answers

1994 bmw 540i brake lining sensor message will not go away

I suspect the control box is faulty,because it is the one that helps display faulty msgs

Jul 30, 2017 | BMW 540i Cars & Trucks

2 Answers

Oil pressure light comes on and it chimes momentarily when start up eventually goes out could this be a sensor and if so where is it located .

Try this is you have just changed your oil. This is a oil light reset.

Turn the ignition to ON.

Press the GAGE INFO button on the driver information center (DIG) switch to view OIL LIFE INDEX.

Press and hold the RESET button on the DIG until the display reads OIL LIFE INDEX 100% NORMAL.

The engine oil life monitor is now reset..

Turn the ignition OFF.

Dec 06, 2010 | 2005 Buick LeSabre

2 Answers

2007 bmw 525xi turn off service light for rear brakes

to reset light brake sensor must have been replace close door turn key on but dont start car when time is displayed on instrument cluster press and hold button on left side of cluster a orange triangle will appear keep holding next service function will be displayed release button to scroll through services that can be reset just push button again without holding when rear brakes are displayed on cluster press and hold button again the message reset with a question mark will come up release button and then press and hold again and light will reset

Jun 18, 2010 | 2007 BMW 525xi Sedan

3 Answers

How to shut off Brake wear sensor after pad change

If the brake pads were worn enough to activate the warning light the sensor or sensors must be replaced. There is no reset for this.

Oct 24, 2009 | 2004 Lexus LS 430

3 Answers

My 1998 Golf SE has 'Service oil' displayed on the trip when I turn it on. Have checked the oil and it's at the right level, is there something else wrong? Do I need to go to a garage to get this reset or...

You could have a bad oil sensor or there may be a leak somewhere causing the pressure sensor to trip... if you give it some gas when the light is on. Does it go off??

Aug 18, 2009 | 1998 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13685 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides