Question about Cars & Trucks

Open Question

Thermador electric range... Does the top get removed by prying the front edge with a screwdriver?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doorhandle


for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Mar 24, 2014 | 2003 Toyota Avalon

1 Answer

How to remove the drivers door panel on a 1991 honda accord lx


Instructions
    • Insert the narrow edge of the flat head screwdriver behind the edge of the plastic screw covers located on the door pull as well as the rear of the door panel. Remove the Phillips screws located behind the covers with the Phillips screwdriver.
    • 2Insert your flat head screwdriver behind the plastic screw cover located behind the door release. Remove the Phillips screw from behind the cover with the Phillips screwdriver, then slide the door release handle forward and remove it.
    • 3Insert the panel tool behind the front of the door's upper edge to pry out the triangular piece of plastic located there.
    • 4Pry around the edges of the door panel with the panel tool until the panel is loose.
    • 5Lift upwards on the door panel to slide it off the door. Unplug any electrical connectors that are plugged into the back.

Oct 01, 2012 | Cars & Trucks

1 Answer

Door panel removal for window switch repair


This is theinstruction on how to remove door panel of Toyota camry 1. Openthe door as wide as possible and roll the window up completely. Locate andremove five screws and two clips in the door panel. Two screws are located atthe rear of the panel, another two are located under the arm rest, one near thelight and the other in front of the light. The last screw is located in thefront of the arm rest behind a triangle shaped plastic panel, directly belowthe door handle. Pry this panel up with a flathead screwdriver to remove thescrew underneath. The two clips are near the front of the door and are smallplastic circles. Push them in with a small screw driver and pull them out. 2. Remove the plastic trim around the doorhandle. Use a flathead screwdriver or prying tool to pop the plastic out fromthe door panel. Wiggle it around until it comes loose from the door handle. 3. Use a flathead screwdriver or prying tool atthe bottom edge of the door. Pry away from the door until the clips under theedge pop out. These are plastic clips under the edge of the bottom and sides ofthe panel. Gently pop them out from the entire door panel. The top of the panelis held in place by the window trim. Move the panel back and forth until it isfree from the window trim. 4. Unclip the wire connectors and wires with aflathead screwdriver. The door panel is now free from the door.

Nov 29, 2010 | 1995 Toyota Camry

1 Answer

How to remove door panel on 2000 silverado


Hello my name is Ben and I can help you with this. Look toward the front bottom and remove that screw, then there is one at the armrest. If power windows, carefully pry the switch assembly up and disconnect electrical connectors. If manual windows, there is a clip shaped like a " C " that holds the handle on a grooved shaft shaft. You can either buy a special tool to remove the clip or use a very thin screwdriver and pry it off from behind the crank handle. It helps to push the door panel in slightly to gain access to the back of the crank handle. CAUTION, the C clip has a tendency to fly off into outer space never to be seen again. Carefully pry out the trim piece around the door handle. Next remove that triangle shaped plastic piece at the top of the door trim, it just comes straight out, ( use a small screwdriver or putty knife to gently pry it out from the edge ) , once you are sure you have found all the screws, start at the bottom of the panel and pry it out, when the fasteners are out lift the panel up.If you meet STRONG resistance double check for any screws you missed. If you have any questions about this feel free to leave a comment and I will try to clarify my answer, Ben.

Oct 20, 2010 | 2000 Chevrolet Silverado

1 Answer

How to remove lexus sc400 door panel. i taken all the screws apart but got hung up at the door latch. are there any screws there to remove.


Hi,

Take a look at the steps involved.

First remove the window/lock control panel by prying up from the front edge, then sliding forward. Disconnect the electricals and set aside.


b9271bd.jpg


Pry the filler panel out from behind the inside door release handle.

71af83a.jpg


Remove the two screw covers on the front edge of the door panel, then remove the 8 screws:

c7f64ba.jpg

Use a screwdriver or other prying tool to pop the 6 clips snapping the panel to the door frame:

6c0756d.jpg

Lift the door panel away and up to remove it from the door frame and allow access to the regulator.
Be cautious when prying the clips loose and removing the panel; the plastic gets brittle with age and has been known to crack rather easily.

Good Luck!!

Thanks!!

Aug 14, 2010 | 1993 Lexus SC

1 Answer

The handle doesn't open the door from the inside, how do I remove the drivers door panel and investigate the problem? I have PWR W&L on the door as well. Thank you Tom


Look toward the front bottom and remove that screw, then there is one at the armrest. If power windows, carefully pry the switch assembly up and disconnect electrical connectors. Carefully pry out the trim piece around the door handle. Next remove that triangle shaped plastic piece at the top of the door trim, it just comes straight out, ( use a small screwdriver or putty knife to gently pry it out from the edge ) , once you are sure you have found all the screws, start at the bottom of the panel and pry it out, when the fasteners are out lift the panel up.

Jul 29, 2010 | 1999 Chevrolet C/K 2500

1 Answer

Unsure on how to remove a door panel so I can replace a power window regulator


Hello, my name is Ben and I can help you with this. First use a small screwdriver or pry tool to pop the switch assembly up, go in under the lip and pry up, then unplug the electrical connections, look toward the front bottom and remove that screw, then there is one at the armrest, then remove that triangle shaped plastic piece at the top of the door trim, it just comes straight out, ( use a small screwdriver or putty knife to gently pry it out from the edge ) , once you are sure you have found all the screws, start at the bottom of the panel and pry it out, when the fasteners are out lift the panel up.

Jun 27, 2010 | 2002 GMC Sierra 1500

1 Answer

How do I remove inside door panel with electric lock and windows. On a 2001 Silverado extended cab, 1500. thanks


Hello, I can help you with this.
Look toward the front bottom and remove that screw, then there is one at the armrest. With power windows, use a small screwdriver and carefully pry up on the switch assembly and unplug the connectors. remove that triangle shaped plastic piece at the top of the door trim, it just comes straight out, ( use a small screwdriver or putty knife to gently pry it out from the edge ) , once you are sure you have found all the screws, start at the bottom of the panel and pry it out, when the fasteners are out lift the panel up.

Apr 12, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Need to remove door panel passenger. 1999 chevy 4x4 extented cab


Hello, I can help you with this.
Look toward the front bottom and remove that screw, then there is one at the armrest, then if you have manual windows use a hooked tool or a special door handle removal tool to release the retaining clip on the inside of the crank handle. With power windows, use a small screwdriver and carefully pry up on the switch assembly and unplug the connectors. remove that triangle shaped plastic piece at the top of the door trim, it just comes straight out, ( use a small screwdriver or putty knife to gently pry it out from the edge ) , once you are sure you have found all the screws, start at the bottom of the panel and pry it out, when the fasteners are out lift the panel up.

Mar 25, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

How to remove rear door panel on 95 taurus


According to the Haynes book, remove window crank or pry off electronic control assembly. With a large screwdriver or pry bar, disengage the clips along the bottom. Once clips are disengaged, swing panel out from bottom and then pull the panel front edge straight out of the door so it clears the molded-in guide pins. Lift the panel straight up and disconnect any electrical connections. Should be done.

Nov 18, 2009 | 1995 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...