Question about Cars & Trucks

Open Question

Bought a EasyNew 32 light bar and wiring harness but it did not come with installation instructions for wiring harness. How do I wire it into her existing system?

Chrysler P/T Cruiser

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

keemo68
  • 1263 Answers

SOURCE: 2007 HHR Wiring diagram

is there spark? is their fuel? also if it was wrecked chances are that the fuel cut-off switch was triggered. i have not ever worked on one so i don't exactly know where it is but i would check behind the fabric/hard plastic right rear/left rear wheel hosing and see if you can hit the reset switch. another suggestion is go to napa or oreillys and get a repair manual for it it has diagrams and schematics in it and it cost about 20 bucks.....good luck please rate this.....thanks

Posted on Sep 01, 2008

  • 32 Answers

SOURCE: WIRING HARNESS FOR 2001 GMC JIMMY

Unfortuantely, there is not a plug in wiring harness for this vehicle. You will have to splice in a 4-Flat Plug. No converter box is needed since it's a standard 2-wire system. You can view this part if you click here.

White - Ground
Yellow - Left Turn
Green - Right Turn
Brown - Running Lights

Now, this is only to wire you to a 4-flat. If you need a bigger plug like a 6-way or 7-way, there are adapters. You can view these if you click here.

If you are going to install a brake controller also, you will need another wiring kit that includes a circuit breaker and wire. You can view this here.

Hope this helps!

Posted on Nov 12, 2008

  • 3 Answers

SOURCE: Tow bar trailer socket wiring connection point to car wiring?

The connectors for towing wire harnesses on foresters are generally on the passenger side, below the rear taillight inside the cargo space. some require pulling up the foam block that is between the spare tire compartment and the taillight. Check where you replace the tailights from inside the car, if there isn't a matching connector hanging out there, check around the spare tire compartment, see if you can remove the carpeted foam block next to the compartment and find the plug under there.

Posted on Mar 03, 2010

seanpwright
  • 2030 Answers

SOURCE: Installing roof mounted dvd system

The door control wire can be picked up from any of the doors light switches in the door jamms.

the ACC+ wire must connect to a source at the fuse panel that has 12 volts to it only when the ignition is turned on.

Posted on Mar 31, 2010

  • 1 Answer

SOURCE: 06 chrysler 300 wiring harness diagram

Need color wire diagram to bypas the ignition transponder. I have the module and the chip key.

Posted on Dec 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Interior fuse box. There are 3 fuse slots that are not id'd with no fuse in place. What do they go to?


there is no need to go any where near the fuse box
trailer shops and tow bar fitting shops sell a piggy back harness where you pull the plug of the back of a tail light and the piggy back connect plugs in with the car harness plugging into the back of that piggy back plug
run the wires out to the trailer connection and connect as per the wiring numbers instruction
quick easy and for most part fool proof

Nov 14, 2015 | 2004 Nissan XTerra

1 Answer

Can someone show a wire diagram for a light bar with switch and 4 pin relay. Just not sure on the diagram. Thanks


Light bar? Third party device? I'd recommend the MFG website for their installation instructions if there are none that came with the new part. Or try the store you bought the part from.

May 05, 2015 | 2015 Subaru Forester

1 Answer

Wiring diagram for a toe bar


that will take some major rewiring, no?

front toebar. wiring. to tower hitch.

first off we dont know what is towing car, nor its hitch wiring

but in most cases, you may need and adaptor, to convert simple

USA wiring to Euro type wiring.

there are 2 systems. that cant just be wired in willy nilly.

is this permanent? one tow , only

or for ever. we cant guess that.

if 1 tow ,why not use clamp on aux light bar and get it done

rent them at u-haul?

if perm, is need , get a pro shop to do this.

how to do this and not damage the cars , electronics that controls

lights can be very tricky.

the safest way is to have new connector installed to rear lights.

to the main harness, then you unplug the cars harness side

and then connect the tow bar new custom harness connector to the rear.

none of this is easy or simple.

tell more get more.

Sep 12, 2014 | Suzuki SX4 Cars & Trucks

1 Answer

Install rear backup camera


PYLE, 3.5 MONITOR INSTALLATION INSTRUCTIONS, INSTALLED IN SUV. As others have mentioned ThePyle Instructions are pretty much non-existant. As a formerly ASE Certified mechanic I am posting this to try to help others.THE PYLE KIT: Monitor + Camera Mount + Wiring Harness for hard wiring into vehicle electrical. --- Additional Materials Required to Install: 3ea. coils of automotive 18 ga. wire. One red, one black, and one white. 1/8" non insulated wire but connectors, wire shrink wrap (1/4", 3/16\', 5/16" AND 3/8" best to get assort. pack). Self taping sheet metal screws 1/2" long. Roll of electrical tape, Barbed Butt Connectors (2ea.- see illustration wiring Monitor posted this site). Rubber wire grommet 3/8" outside, 1/8" for wire, 1ea. req. Pull ties. --- Tools Required: Utility Knife, Drill w. phillips bit driver, wire tripper, volt meter, small pry bar. + Misc. ---

Mar 16, 2013 | 2004 Hyundai Santa Fe

1 Answer

Should i have any spare wires when hooking up an after market car stereo


Yes, It's a very good possibility that you will have a few wires left over. Normally a wire for an aftermarket amp to be triggered on when you turn your radio on and possibly a power antenna or a dimming function that dims your radio lights when your headlights are on. It of course always depends on if you have a power antenna or not, or if you have an aftermarket amp or not or if you have the dimming feature on your car or not. These wires don't apply to everyone.
You will just match the colors between the wiring harness that came with the DUAL radio and the interface adapter that goes to your car. Make sure you use **** style crimp connectors. If not the wires could come loose or cause a popping noise or cause the radio to turn off while driving.
Other than that, installing an aftermarket radio is mostly matching the colors up between the two harnesses and crimping the wires together.3_6_2012_2_31_36_am.jpg

Mar 06, 2012 | Cars & Trucks

1 Answer

Need directions to fit towbar and wiring on holden captiva sx (2007)


there is a standard tow bar and a 2000kg for genuine tow bars
you need to remove both tail lights,the bumper bar and reinforcement bracket, spare wheel and exhaust hangars on rear mufflers, remove the tie down bracket on LHS chassis rail(dont need this or the bolts that hold it on), so you can then bolt in place either of the 2 tow bars.
genuine wiring patch harness for trailer plug is my suggestion since its plug straight into vehicle and interfaces with vehicle, goes in right hand rear compartment remove lid then remove box, interface connector for trailer harness is there.
instructions can be printed out from dealers if you ask
some new kits dont come with instructions in kits because information is on dealer computers
there is a template to print out to cut hole in bumper bar for tounge area of tow bar, uses centre square dimple in bar but its a bit wider.

Sep 05, 2011 | Daewoo Korando Cars & Trucks

1 Answer

How do you hook up trailer lights so i can pull a trailer


If you bought the Honda hitch kit, a wiring harness and instructions are included. If you bought a different kit, buy the wiring harness from Honda. The harness connects to a plug located in one of the accesses panels in the back. You will have to take off the. Bumper facia to route the harness to the hitch. Be sure to use the rubber grommets to prevent the sheet metal of the rear quarter panel from wearing through the wire insulation and causing a blown fuse.

Aug 07, 2011 | 1997 Honda Passport

1 Answer

Where do i feed the wires through to wire up the towbar on a 1997 honda crv?


If you have a wired tow hitch on your car you will need to mate this to the wiring harness on the tow bar. If the two wired units do not match then you will either need an adapter or will need to rewire the tow dolly or the car. If the car doesn't have a tow light unit installed you will need to install one that will mate to the tow bar light unit.

I hope this helps - please rate me

Mar 18, 2010 | 1997 Honda CR-V

1 Answer

New Car Radio, New Harness but no power, Nissan P/U '95


here is the factory harness wires and what they do, recheck thayt it all matches up.

1995 Nissan Pickup Truck Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Pink
Car Radio Accessory Switched 12v+ Wire: Blue
Car Radio Ground Wire: Gray
Car Radio Illumination Wire: Red/Blue
Car Stereo Dimmer Wire: Red/Yellow
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Pink
Left Front Speaker Negative Wire (-): Blue
Right Front Speaker Positive Wire (+): White
Right Front Speaker Negative Wire (-): Black
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Light Green
Left Rear Speaker Negative Wire (-): Violet
Right Rear Speaker Positive Wire (+): Blue
Right Rear Speaker Negative Wire (-): Pink
-->

Mar 10, 2009 | 1995 Nissan Pickup

2 Answers

Jeep 2008 unlimted trailer wiring


I just bought a wiring adapter from mopar for this. you take off the rear tail light on the drivers side and unplug it from its harness. the mopar wiring kit i bought plugs into the wiring from the car and has two outputs on it. one for the tail light and a longer one that will run down thru the frame and come out under the bottom by the bumper in just the right spot. i has the plastic clips in just the right spots for snapping into the frame underneath too. took me 5 min to install no splicing required. i got mine off ebay for about $20. super easy! good luck!

Jun 18, 2008 | 2008 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...