Question about 2006 Chevrolet HHR

1 Answer

What will it take to correct? trouble shooting p1574 code shown on a 2006 HHR

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 11,730 Answers

DTC P1574 Stoplamp Switch Circuit
The cruise release switch is a normally closed switch. The stop lamp switch signal circuit is a normally open switch. When the brake pedal is released, the engine control module (ECM) detects a high voltage signal on the torque converter clutch (TCC) brake switch/cruise control release signal circuit and a low signal voltage signal on the stop lamp switch signal circuit.

Diagnostic Aids
In order to avoid a misdiagnosis, perform the following:
• Inspect for proper operation of the stop lamps. Refer to Exterior Lighting Systems Description and Operation .
• Inspect for proper adjustment of the stop lamps. Refer to Stop Lamp Switch Adjustment .
• For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .

2
Do the stop lamps work properly?
YES - Go to Step 3
NO - Go to Stop Lamps Inoperative
3
Test the stop lamp switch signal circuit for an open or for a high resistance between the body control module (BCM) and the engine control module (ECM). Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
YES - Go to Step 6
NO - Go to Step 4
4
Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES -- Go to Step 6
NO - Go to Step 5
5
Replace the ECM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
YES - Go to Step 6
--
6
Use a scan tool in order to clear the DTCs.
Operate the vehicle within the Conditions for Running the DTC.
Does the DTC reset?
Go to Step 2
System OK

Posted on Dec 28, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to find trouble code on a 2006 hhr?


Its your electronic steering motor

Jul 01, 2014 | 2006 Chevrolet HHR

1 Answer

2006 chevy hhr hvac blower/fan


The fan is normally used for both heating and cooling. Check the owners manual for the fuse location and see if it is blown. If so, replace it and try the fan again. If the fuse blows again, the motor is probably seized and will need a mechanic to oil and free or replace it. If you can get to it your self, BE CAREFUL, and touch the motor when it is turned on. if it gets hot without turning, it is probably electrically OK and seized. If it does't get hot or hum and the fuse is OK, Its either bad or has a problem that will need to be traced. Best to take it to a GOOD mechanic that you trust. Trouble shooting can get complicated.

Nov 20, 2013 | 2006 Chevrolet HHR

1 Answer

Trouble codes P0303 and P1174 on a 2006 chev hhr with a 2.4litre engine


You may need a shop manual to get the testing procedures.
Code 303 is for a miss on cylinder 3 which could be ignition or fuel related.
Code 1174 is for a problem with the fuel trim which could be due to the problem with cylinder 3 or something else.

Sep 02, 2013 | 2006 Chevrolet HHR

1 Answer

Why does the engine shut off on 2006 hhr when message engine power reduced displays


Could be something causing the engine to die which is making the warning light come on, or something that the computer sees as a threat of damage to the engine and the computer is shutting down the engine to prevent damage.
You would have the computer scanned for trouble codes and then proceed with troubleshooting the issue.

Apr 06, 2013 | 2006 Chevrolet HHR

1 Answer

Heater&a/c stopped working


First thing to do is get the computer scanned for trouble codes.
It could be a thermostat or several other things.

Feb 28, 2013 | 2006 Chevrolet HHR

2 Answers

Chevy 2006 hhr light says t/c what does this mean?


Could be for the traction control.
You would need to have the body computer scanned for trouble codes to proceed.

Jul 11, 2012 | 2006 Chevrolet HHR

1 Answer

2006 hhr 2.4 won't start after replacing both camshaft position sensors.


Did you remember to plug in the MAF sensor? Are you sure the air chamber is correctly installed on the throttle body?

Feb 18, 2012 | 2006 Chevrolet HHR

2 Answers

Where is the power stiring fluid located at


Hello, this vehicle doesnt have a hydralic power steering fluid system. this vehicle uses a electric power steering system. if you are having power steering issues with this veicle, you will need to have the electronic steering system scanned for trouble codes

Dec 09, 2010 | 2006 Chevrolet HHR

1 Answer

I have several codes in my Nissan Titan after installing aftermarket headers and catalytic converters. I have the following codes: P1148, P1168, P0130, P0150, P0153, P1564 and P1574. I also installed...


lambda probes are fitted between the exhaust manifold and the first box(cat)cannot miss them as no other part of the exhaust system has wires coming out of it.

Jul 14, 2010 | 2006 Nissan Titan

1 Answer

I need new front struts on my hhr, What do I need to purchase for an auto parts store so I can have them replaces.


if you don't have the correct tools don't try to do it you self. the springs are under alot of pressure. can break your neck if it shoots out. have a shop do it for your safety

Aug 06, 2009 | 2006 Chevrolet HHR

Not finding what you are looking for?
2006 Chevrolet HHR Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...