Question about 2000 Ford Contour

1 Answer

How do i fix the reverse lights on my 2000 ford contour?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 660 Answers

1. check fuse.
2. change bulbs.
still not working, remove housing around shifter and see if connection has come loose that operated the reverse lights.

Posted on Dec 29, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove tail light lens on 2000 ford contour SE


Open the trunk. Pull back the trunk lining where it covers the tail light access inside the quarter panel. Remove the lamp sockets for the turn/stop and backup lights, and remove the screws that hold the lens in place. The lens will then pull out from the quarter panel. Installation is the reverse: make sure the rubber gasket is in place properly.

Jan 28, 2013 | 2000 Ford Contour

1 Answer

Transmission stuck in reverse on 2000 ford contour


linkage will probally have to be readjusted if your lucky, Get it check out before it gets worse, End does damage to the transmission, If it hasnt happen allready,From trying to force it into gear,

Nov 27, 2012 | 2000 Ford Contour

1 Answer

I can't find the fuse box that has the reverse lights fuse in it


check up underneath the dash between the door and steering wheel

Aug 15, 2010 | 2000 Ford Contour

3 Answers

How to fix ford contour code p0708


this code indicates a problem with the transmission range selected switch, this switch is on the transmission case where the shift cable attaches, when u select a gear it sends a signal to the computer control that u want lets say Reverse by sensing the range selector switch feedback, replace the switch will most likely cure the code, then clear the code and drive a few miles.

Jul 22, 2010 | 1995 Ford Contour

1 Answer

Replaced a alt on ford contour


dis-connect bat, take off serp belt, unbolt alt, remove wires from alt, install reverse order

Feb 04, 2010 | 2000 Ford Contour

1 Answer

Replacing a fuel pump on a Ford Contour


Fuel Pump Module —Vehicles with Returnless Fuel System
Special Tool(s) Wrench, Sender Unit, Fuel Tank
310-065A (23-054) Removal
syp~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
  1. Remove the fuel tank.
  1. Using the special tool, remove the fuel pump locking ring.
  1. Remove the fuel pump module.
    • Rotate the pump counterclockwise to remove.
  1. Remove and discard the O-ring seal.
Installation
syp~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
  1. Install a new O-ring seal and locking ring.
  1. To install, reverse the removal procedure.

Jan 07, 2010 | 2000 Ford Contour

1 Answer

I would like to know how do i get to the light in the dash


disconnect battery , lower steering column, remove fascia, remove bezel, remove Instrument Cluster, replace bulbs as required, reverse, reinstall, reinspect.

Oct 13, 2009 | 2000 Ford Contour

1 Answer

P0503 p1451 codes


do it step by step
p0503
1- change vss sensor and recheck
2- check wiring of vss sensor
p1451
1- check wiring of EVAP vent
2- change Evap vent

Sep 16, 2009 | 2000 Ford Contour

2 Answers

1998 Ford Contour ABS light and one wheel partially braking


could be but not likely. sound like abs pump or abs ecu failure. to make sure check DTC's

Jun 02, 2009 | 2000 Ford Contour

1 Answer

How do you fix a 2000 ford contour oil pump?


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 20, 2009 | 2000 Ford Contour

Not finding what you are looking for?
2000 Ford Contour Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...