Question about Cars & Trucks

Open Question

When i put in a resistance number nothing happens

Posted by Anonymous on

  • james laughton
    james laughton Dec 28, 2016

    Hi Anonymous, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to test a blower resistor on a 1997 Toyota Avalon.

Hi Tony,
You need to put a multimeter across the resistor and measure the resistance. Finally you need to compare the measured resistance against the quoted resistance. Look online for:"resistance of blower motor ". You'll find a number of sites w
hich could be useful:

Illustrated Guide for Car Buyers and Owners

Jul 25, 2015 | Toyota Cars & Trucks

1 Answer

2000 Ford F250 Disel: Nothing works on the panel for the a/c heater. The fan does nothing when you change speed there is nothing that comes out, there isnt any heat or cool, and when you turn the dial...

Pull the wires from the blower. Throw 12 volts and a ground to it(red is B+). If it comes on, it is good. Replace the controller. If it was the relay, some sort of blower speed would have happened. There are other wires to check, but you would have to loose other things to go this direction. Like accessory and ignition.

Jan 10, 2015 | Ford Cars & Trucks

1 Answer

1992 Buick Lesabre, my a/c / heater is not working, after putting in a blower motor resistor/relay. The dash doesn't not illuminate, and the only trying that works is the defrost for my back window. Is...

My 92 Le saber did that and we changed resisters and did a number of things and nothing worked Finally my mechanic put a bypass switch some where on the power line and after that it worked. Sorry I am not sure where but after he put a cut off switch in the line everything worked again.I don't own that car anymore so I can't even follow up to see where it went.

Nov 08, 2014 | 1992 Buick LeSabre

1 Answer

Reverse lights

nice double post, back up one and read.
but now adds MANUAL.
so the reverse switch is bad, remove it ,2wire switch
and put in new.

its just a simple Thomas Edison switch, (no electronics) nothing magic. the FSM< covers this, (factory service manual) as does
if an OHM meter (resistance low range) shows infinity in reverse its bad, if reads 0 ohms its good, so if good, the wires to it were bad.
or both lamp out, (can happen, ignored)

Nov 09, 2013 | 2000 Suzuki Esteem

1 Answer

Key turns to "start" position. Nothing happens, key doesn't spring back to "run".

Sounds like the link between the lock cylinder and the switch is broke.

Jun 13, 2013 | 1993 Dodge Shadow

1 Answer

What happen when an ohmmeter is connected across an energised load.

Nothing should happen as long as the ohm meter has a high resistance like 10 megohms or higher.

Nov 04, 2011 | Cars & Trucks

2 Answers

When you press down the clutch nothing happens

The master,or slave cylinder ,are bad.

May 25, 2010 | 1990 Toyota Pickup

1 Answer

Rear a/c blower motor failure on '04 suburban

Your skills at running a Volt Ohm meter need refreshing at the very least. You can not have all the conditions you describe, especially the zero resistance part as you would be blowing fuses if you actually had power to the zero resistance motor. Yet you say you still have power - not possible in MY universe at least.

But if it is an infinite ohms reading that you got, then the motor is open somewhere internally and needs to be replaced. And most all your symptoms match this condition, so I'll assume you don't know what you are looking at yet as far as digital meters go - don't feel bad, they mess me up too.

Aug 28, 2009 | 2003 Chevrolet Suburban 1500

1 Answer

No blower on any setting, no air cond. also.

check to see if you have power at wires at blower if u do then replace resister 1 more time but first... put power to blower motor if it comes on replace resister

Jun 25, 2009 | 2003 Dodge Dakota Club Cab

2 Answers

Vauxhall Astra 1.4 gsl (M - Reg)

Have your blower motor resistor checked,this is the most likely solution.

Oct 24, 2008 | 1998 Volkswagen Beetle

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides