Question about 2006 Mercury Mariner

Open Question

How do i find the key code on the key pad for my 2006 mercury mariner

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 28 Answers

SOURCE: 2006 mercury mariner. stupid tail light assembly.

they are hard to take off sometimes, you are doing it right just keep willing it it will come off, there is 2 gromits that hold it into place might have a little dirt into the plunger.

Posted on Feb 22, 2009

  • 1596 Answers

SOURCE: what tool do i need to replace front brake pads on 2008 mariner?

You Will Need A 13-14 mm Wrench for Caliper Bolts .A Large Flathead Screwdriver to Spred open Caliper/Shoes to Remove Caliper from Rotor,
After rhis you Can use a LARGE "C" Clamp to CLOSE Caliper Piston.

Posted on Nov 06, 2009

  • 1 Answer

SOURCE: 2006 Mercury Mariner - sticky gas pedal

I have a 2005 Mariner with the same problem. Always when the weather drops

Posted on Jan 09, 2010

  • 108 Answers

SOURCE: procedure to replace alternator 2006

  1. Disconnect the negative battery cable.
  2. Remove the lower splash shield bolts and the pin-type retainers.
    NOTE The LH lower splash shield must be removed before the RH lower splash shield.
  3. Remove the lower splash shields.
  4. Rotate the front end accessory drive tensioner counterclockwise and position the accessory drive belt aside
  5. Disconnect the alternator electrical connector.
  6. Position the alternator B+ protective cover aside and remove the alternator B+ terminal nut.
  7. Remove the A/C compressor bolts. Use a tie-strap and position A/C compressor aside.
  8. Loosen the alternator nuts.
  9. Remove the lower alternator studs.
  10. Remove the upper alternator bolt and the alternator.


Posted on Feb 18, 2011

  • 1975 Answers

SOURCE: I recently purchased a 2008

You need to have the code that came for that vehicle. There are 2 places that you can look to find the code. Sometimes you can find a sticker in the back tailgate area it will be white and most of the time it is on the right (passengers) side. The other place you may be able to located is in under the hood most of the time it's on the drivers side firewall by the brake master cylinder. It will be a metal plate with 5 numbers on it like the sticker will have in the back if one is there. I hope this helps and good luck.

Posted on Mar 25, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i find the code on the key pad on my 2006 meecury mariner

The code for the keypad? Should be the same process as for the Ford Escape:

Dec 28, 2016 | 2006 Mercury Mariner

1 Answer

Need to change code on door key pad

  • Enter the five-digit code programmed into the keypad from the factory. Find the key code in the card stored in the glove box of your Mariner.
  • Press the "1-2" button on the keypad immediately after inputting the factory code.
  • Enter the five-digit key code you wish to store for your keyless entry system within five seconds of pressing the "1-2" button.

  • Read more :

    Jul 05, 2015 | 2008 Mercury Mariner

    1 Answer

    Key pad code

    you will need to go see cal or other ford dealer for code abs light comes on when you have a brake problem may need new pads or wheel hub do check it as this is what stops the car and no brakes is no good pat

    Aug 29, 2014 | 2006 Mercury Mariner Hybrid

    1 Answer

    Have a 2006 mercury mariner key is stuck in ignition how do I get it out

    Open up steering column, you'll see a sensor (mushroom shape)which has a wiring harness attached.Detach harness, key will release.-----------------------------------------------------------------------------------
    PSA BSI tool

    Mar 21, 2013 | 2006 Mercury Mariner

    1 Answer

    Need location of 2006 mercury mariner security module to get keyless door pad code

    I have a 2006 Ford Explorer and I just found my keyless entry module. The module was behind the lower plastic panel on the passenger side rear panel right below the seat belt height adjuster. Not the panel with the seatbelt adjuster but the one below it. No tools were needed and it took me all of 5 minutes. Just pop off the front of the panel closest to the door and pull it back. Use a light and you can see the large 5 digit code on top of the module. Thanks very much to the people that contribute to this forum....Cheers
    This is really where it is!

    Nov 12, 2009 | 2006 Mercury Mariner

    1 Answer

    Cant find what size or what they used ?? who has did brakes of

    jc whitney's front pads: Rear shoes: They've got rotors if you need them too.. k

    Jun 06, 2009 | 2006 Mercury Mariner

    1 Answer

    Unable to start my 2006 mercury mariner

    my sister was using the wrong key!

    Jan 22, 2009 | 2006 Mercury Mariner

    1 Answer

    Keypad entry code

    call dealer they will help you out promise

    Jun 24, 2008 | 2006 Mercury Mariner

    Not finding what you are looking for?
    2006 Mercury Mariner Logo

    Related Topics:

    47 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercury Experts


    Level 3 Expert

    76848 Answers


    Level 3 Expert

    5546 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Are you a Mercury Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides