Question about Nissan Cars & Trucks

Open Question

Hi. I'm looking for the torque wrench settings for every component of a Nissan GA14 1996 Engine and GA16 head

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head torque settings of 1983 Nissan Langley 1.5


try this link , i'm not sure if the list goes that far back but worth a look, click on torque tables and look up your vehicle
http://www.speedwayautoparts.com/index35.htm

Oct 14, 2014 | Cars & Trucks

2 Answers

Citreon xsara 1999 1.8 16 valve cylinder head torque settings


If yours is an Xu series engine, you need to use a torque wrench and an angle dial wrench. Tightening is in 3 stages.
  • Stage 1: Tighten up to 60Nm (44 lb/ft) then fully loosen
  • Stage 2: Tighten up to 20Nm (15lb/ft) change to angle dial wrench
  • Stage 3: Angle tighten to 300 deg.
To avoid confusion, do stage 3 in 3 steps, tighten 100 deg each round and repeating the cycle until 3 rounds.

07718717-6a90-48f5-a87c-bc1ff81d67bd.jpg

04a9b611-4f0b-4da6-9052-a1cb2e517c02.jpg

Jun 13, 2014 | 1998 Citroen Xsara 1.6

1 Answer

TORQUE SETTINGS FOR CYLINDER HEAD ON TD27


not sure what engine this is but if its a diesel cargo or serena with a cast iron head no turbo then around 80lbs ,if a smaller petrol engine with a alloy head then about 60lbs ,personally i never use a torque wrench i do it by experiance and feel ,like feeling for the bolt stretch if this sounds right but ?? you have to do plenty of them to know

Apr 04, 2012 | Nissan Nissan Cars & Trucks

1 Answer

Hi i'm eduardo and i have a '94 nissan pathfinder 4wd...engine 3.0.... i want to know the head torque specifications .


Hi Eduardo:
Check this information (click over pics for zoom)...

zjlimited_1062.jpg

Fig. 20: Exploded view of the cylinder head assembly-VG30E engine


zjlimited_1063.jpg

Fig. 15: Cylinder head loosening sequence-VG30i and VG30E engines


zjlimited_1064.jpg

Fig. 17: Cylinder head torque sequence-VG30i and VG30E engines


Install the cylinder head with a new gasket. Apply clean engine oil to the bolt threads and seats, then install the bolts with washers (beveled edges up) in the correct position. Note that bolts 4, 5, 12 and 13 measure 5.00 in. (127mm), and are longer than the others. The other bolts are 4.17 in. (106mm) long.

Tighten the bolts in the proper sequence, in the following stages:
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 43 ft. lbs. (59 Nm).
Loosen all bolts completely.
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 40-47 ft. lbs. (54-64 Nm). Or, if you have an angle torque wrench available, tighten them an additional 60-65 degrees.


Hope this helps; remember to rate this answer. Good luck.

Apr 22, 2011 | Nissan Pathfinder Cars & Trucks

1 Answer

Need torque specs and sequence for nissan ka24e cylinder head.


Hi! i hope this will help you.
tighten in 2 steps:
1st - 22ft.lbs
2nd - 58ft. lbs
then loosen all bolts completely.
Final torque is in 2 steps:
1st- 22ft. lbs.
2nd - 54-61ft. lbs
( if angle torquing in 2nd step, turn all bolts 80 to 85 degrees clockwise with an angle torque wrench. ) i hope this will help you.

Sep 19, 2009 | 1991 Nissan Stanza

1 Answer

Need 1990 nissan sentra torque settings and valve clearence


heinrichkemp: The engine in your car is a GA16i
I venture you are asking about the head bolts when you refer to torque settings. The head bolts used on this motor are torque to yield (streach bolts) If you are reusing them, you need to check them to insure they are not stretched beyond limits.
The way you measure the bolt is with a micrometer.
Measuring close to the end where the bolt starts to thread in, about 10-12 threads up, take a reading. Now, go to the other end of the bolt where the threads end and measure about 10 threads in.
There should not be more than a .009 inch difference (.228mm). If there is, discard the bold and get a new one.

You must use a sequence to tighten the bolts, below is the sequence.
11
13 9 3 1 6 8

14 7 5 2 4 10
12 15

torque 11,12,13,14 & 15 to 8.3 Nm (6.1 ft lbs)
Torque the main head bolts by the numbered sequence to
29Nm (22 ft lbs) first pull
64Nm (47 ft lbs) second pull
Loosten all the bolts completely
Tighten the to 29Nm (22 ft lbs) first pull
Tighten bolt # 1 clockwise 85 degrees
Tighten bolts #2- 10 65 degrees
Nissan noted that if you do not have a torque angel meter, you can use a regular torque wrench and torque all the bolts to 69Nm (51 ft lbs)
The valves on this engine have hydraulic lifters, consequently require no adjustment.

Apr 11, 2009 | 1990 Nissan Sentra

4 Answers

Torque wrench settings


please understand there are a lot of items on a car that require torque settings every thing from the lug nuts to every engine bolt, and transbolt. please be more specific

Jul 03, 2008 | 1999 Ford Taurus

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...