Question about Isuzu Cars & Trucks

1 Answer

Removing a cv axle from a 1997 isuzu trooper front right

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 20,706 Answers

Try mitchells yet>

its not free, but good.
most top shop have a full license
or buy a real manual used.
(book stores, on the net) or fleabay.


http://www.eautorepair.net/Marketing/Default.asp

Posted on Dec 28, 2016

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

germcelchar
  • 389 Answers

SOURCE: how do i remove cv axle for a 98 isuzu trooper

Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Posted on Sep 28, 2009

BCAS1298
  • 3092 Answers

SOURCE: Do I have to remove 4 bolts around axle to replace

Yes

Posted on Dec 13, 2009

honeymokey
  • 3113 Answers

SOURCE: CV axle removal 1999 Isuzu Trooper

The easy way is to take the inner boot off and take the joint apart. Take new cv axle apart at inner joint and attach to the old one sticking out of axle housing. You will need to get new boot clamp.

Posted on Mar 06, 2010

Suzman
  • 642 Answers

SOURCE: cv axle 4x4 diferencial

Make sure 2- wheel drive is selected.
Jack up the vehicle front and support on axle stands. Remove the wheel.
Remove the brake caliper. It bolts onto the hub carrier(aka knuckle) with 2 bolts from the vehicle side of the carrier so you cant see them without sticking your head into the wheel arch. Slide the caliper off the rotor and hub and hang it with a piece of wire inside the wheel arch. Dont let it hang on the pipe it is connected to. The caliper may be difficult to remove if the rotor has a ridge on its outer edge due to wear.
Remove ABS speed sensor(2 bolts to remove) behind the hub
Next comes the hub assembly. :

  • Shift on the fly:Remove 6 bolts on the cap then the cap itself. Next the snap ring/circlip and the shim behind it.(On the piece of shaft now visible) and then you can pull off the hub flange. Remove the screw on the lock washer and then the washer itself. Remove the hub nut.The hub assembly(with rotor) will now pull off the shaft. Remove inner bearing and oil seal.
  • Manual hub: Select transmission 2H and "Free" on the hub. and run the vehicle about 100 m/300 ft.Remove 6 bolts on the cap then the cap itself. Next the snap ring/circlip and the shim behind it. Remove body assembly.
Remove the bottom ball joint on the hub carrier.(Ball joint removal tool may be needed to free the ball joint. Dont go hammering it. That will damage the thread) Swing the carrier upwards and you should have just enough free space to pull the shaft from the hub carrier. If not remove the top balljoint as well. Remove the clamp/SS strip from the inner CV rubber boot. Pull the boot back on the shaft. Remove the circlip from inside the DOJ case. The shaft can now be pulled from the DOJ case.
Remember to preload the wheel bearing on reassembly. Tighten the hubnut to 29 N.m. then loosen fully. Tighten again by hand. Connect a spring scale to the wheel stud. Pulling on the scale in the direction of rotation should give a reading of 2-2.5 kg/4.4-5.5 lb(new bearing) or 1.2-1.8kg/2.6-4 lb(used bearing) when the rotor starts to move. If it does not, tighten the hub nut a littl and measure again. Repeat till the correct measurement is achieved. See diagram.

2924189.jpg

Posted on Jul 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove cv axel on 01 isuzu trooper


You must remove the axle from the transmission in a straight out line from the case of the transmission in a quick and very hard snapping motion, a large heavy cast iron pipe wrench works well, but remember the axle can't be at an angle, it must be straight out within a few degrees.

Apr 27, 2012 | 2001 Isuzu Trooper

1 Answer

CV axle removal 1999 Isuzu Trooper


The easy way is to take the inner boot off and take the joint apart. Take new cv axle apart at inner joint and attach to the old one sticking out of axle housing. You will need to get new boot clamp.

Mar 03, 2010 | 2003 Lincoln Town Car

1 Answer

How do you remove a front cv axle on a 1997 trooper


You can't just pop the axle out of the front diff assembly. There's a circlip behind the plate that mounts the housing to the frame where the axle passes through. Not a fun job. I usually rebuild those axles by disassembling the axle at the inner joint. If you're ready to take on the task, I'll walk you through it.

Sep 30, 2009 | 1997 Isuzu Trooper

1 Answer

Change a cv boot on a 1996 isuzu trooper


First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers

Sep 28, 2009 | 1994 Isuzu Trooper

2 Answers

How do i remove cv axle for a 98 isuzu trooper


Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Sep 27, 2009 | 1998 Isuzu Trooper

1 Answer

Cv joint replacement 1998 isuzu trooper 4x4


This is a simple job that is why it is not very detailed in your book. Nothing special. Do one side at a time so you have a reference to how to reassemble it. Remove your tire , brake calipers be sure not to stress the rubber brake lines or open the brake lines to air. Remove both upper and lower ball joints. When taking out the ball joints remove the cotter pin and bolt and beat the **** out of the joint for it to release. Then the C/V axles will come right out with a bit out encouragement. You will need a few tools wrenches pry bar hammer. I would buy a Chilton's or a Haynes repair manual for torque specs for reassembly. Good luck and take your time. And unless the axles are making noise you can just replace the rubber boots. Which is alot cheaper.

Jun 01, 2009 | 1998 Isuzu Trooper

1 Answer

Removing half shaft from 2000 isuzu trooper


must remove clips from inside front axle housing!! If the cv joint aint broke DONT FIX IT the boots can be replaced in less than 1 hour with hand tools and the boot is around 20$ at any parts store

Mar 31, 2009 | 2000 Isuzu Trooper

1 Answer

Cv joint replacement


you have to drop the front axle, it is a lot of work.

Jan 16, 2009 | 1994 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...