Question about Tata Cars & Trucks

Open Question

Wiring colours not matching, connecting new telefunkenTFCD-807 in Tata vista

Speakers no problem just power connection Telefunken- Tata Vista Yellow wirefuse positive pole battery -- ? Red wire - ignition lock -- ? Black wire - negative pole battery --? Blue wire connect automatic antenna --?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

angelo63
  • 129 Answers

SOURCE: I have problem with connection of ford xr6 electronic ignitio

the yellow blue is the + side of coil but to be safe get a test light connect one end to the negative side of battery or a good clean earth on the engine turn ignition. Check which wire has power .The one with power is for the + side of coil . Check test light on battery to make sure it works

Posted on Dec 27, 2008

  • 290 Answers

SOURCE: needing wiring diagram for 1991 dodge dynasty le

here is what I found:
http://www.the12volt.com/installbay/stereodetail/715.html

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: Wiring for Bosch Hologen Fog Lights? Wiring

Look on the relay for the terminal numbers.
Terminal 30 goes to the battery positive.Red Wire
The two terminal 87 go to the fog lights.Black Wires
Match the color wire with what you have on the relay connection for the rest of the wires.
Terminal 86 should connect to your low beam headlight.
Terminal 85 should go to the fog light switch.
The fog light switch should connect to the terminal 85 and the other terminal on the switch will connect to ground.

Posted on Feb 04, 2010

roniecon
  • 6826 Answers

SOURCE: Installed new battery in 92 Toyota pickup, now I

You have a wire off some where look real good,one may have fell down under the battery or somewhere,or there is a fusible link burned.

Posted on Apr 04, 2010

  • 67 Answers

SOURCE: i put new positive wire end on battery it have

it doesn't mater as long as they all go to the same terminal

Posted on Nov 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New radio installation power is only problem TelefunkenTFCD-807


re - check the wiring i would. or test if radio works by tacking it out and connecting live and earth to an old car battery. There also usually a fuse at back of radio check that out

Dec 28, 2016 | Cars & Trucks

1 Answer

What is the pairing procedure of ecu with immobilizer of Indica vista


TATA Indica Vista ECM / ECU - YouTube

? 2:26
https://www.youtube.com/watch?v=rRk5zSFA1eg
Mar 8, 2014 - Uploaded by Flip Keys
This video shows how to open TATA Indica Vista and ManzaECM / ECU for repair purpose.

How to extract Immobiliser Chip from Indica Vista key ...

? 0:52
https://www.youtube.com/watch?v=pqG0T99Xce0
Nov 8, 2012 - Uploaded by Flip Keys
If your original Indica Vista key breaks, wears-out or gets damaged then you can re-use its immobilizer chip ...

Maruti Suzuki SX4 ECM / ECU - YouTube

? 2:37
https://www.youtube.com/watch?v=pWjmh1QUhHQ
Jan 12, 2014 - Uploaded by Flip Keys
If you are repairing Maruti Suzuki SX4 ECM / ECU or coding a new immobilizer key then you can open the ...

TATA Motors INDICA VISTA Owner's Manual - ManualsLib





Jan 08, 2016 | Cars & Trucks

1 Answer

Safe Mode stays on


Lets get things straight first, When you safe mode do you mean it's in Limp home mode? When you say the light stays on and does not flicker are you referring to the engine ECU light.If the ECU light is on then there must be a fault code in the systems 100% has to be. Please be more specific.

Jan 07, 2014 | Tata Aria Cars & Trucks

1 Answer

Fitted new stereo, all powered up and signifying output but nothing coming from speakers. didnt have a radio in it when i bought it so unsure where to start looking


Chances are you did not wire it correctly. Ensure you Test the Speaker Wires with a 9Volt Battery to ensure the speakers are good and then match the wires to the corresponding connections

Apr 12, 2013 | 2001 Ford Focus

1 Answer

I need a radio wiring diagram for a Holden Commodore LS 1991


Regardless of colour coding, please follow the following instructions (require multimeter):


Note: Attach multimeter earth wire (black) to the vehicle body. Convenient places may be the metal ignition barrel, the vehicle's car arial plug, cigarette socket body etc.


1) Testing for voltage with key out of the ignition, locate the permanent positive wire. This will wire into the yellow wire on your new stereo. The yellow wire circuit powers the stereo's memory.


2) Testing for voltage again. This time you are testing for a wire which only offers power with the ignition turned on. This one will wire into the red wire on your new stereo, and will power the unit only with the ignition on.


3) Now you know which your vehicle's positive wires are you can now test for an earth wire. Switch the multimeter to the resistance setting. There is one setting which will allow a buzzer to sound once you find continuity. With the ignition off test each wire until you get a buzz and a low resistance reading. This should be your earth wire. Double check this with the ignition in the on position. It should remain the same. If it changes to a positive with the ignition on and with the vehicle's lights switched on, then this is the dimmer feed for the stereo's screen. If you unintentionally found the dimmer feed, then you can ignore this wire, and search again for a wire which only offers an earth.


Now you have your power and earth wires located and can wire these into your stereo before continuing.


4) Next you need to use the stereo's balance and fade controls to allow only one speaker output to work from the stereo. So let's start with Left Front speaker output only. turn the stereo volume to mid way so that you can hear when you have connected to the right speaker. bare the remaining wires on the car side and test combinations of the remaining wires until you find the front left speaker of the car. Wire your stereo's wires once you find the correct connections.


5) Repeat the above steps with all remaining wires, remembering to adjust your stereo's balance and fade controls to only allow one speaker output at a time, to ensure the only one possible channel to work and help you identify which of the car's wires power the speaker you have selected.


Before re-assembly of the dash panel, check that your stereo and all functions work properly, being sure to use your fade and balance controls again to test all speakers individually.


If you want to be extra careful and wire the vehicle's speakers positive and negative, according to your stereo's outputs, not that this makes much difference on standard stereo arrangements, then follow this next step:


Make sure you can see the speakers themselves and connect a 1.5 volt AA or AAA battery to the speaker wires. If the speaker's cone pushes forwards, then the wire you connected to the battery's + terminal is indeed the positive wire and should be wired as such. If the speaker does the reverse, then you have the wires the wrong way around. Do not repeat this test for extended periods as damage may be caused to the speaker circuit.


Tip: Always solder all connections and insulate well from each other. Stereo connections can corrode over time and are prone to movement behind the dash. Poor connections may cause faults and low quality sound.

Oct 30, 2012 | Cars & Trucks

1 Answer

Ford BA XR6 what is the colours negative and positive for the rear speakers


Most speakers have copper wire for positive and silver for negative. The connection will have red + for positive and black- for negative for both speakers.

Aug 04, 2012 | Cars & Trucks

1 Answer

I have a 1995 GMC c1500 sierra the radio wire harness has been cut i am trying to figure out the wires and what they connect to on the back of a kenwood cd player i have connected the basics but i sti


the wire colours for your truck will be different then the aftermarket radio
you will have to locate them and match the wires function and hook them up that way
step 1 - factory wire colours

Nov 27, 2011 | 1995 GMC Sierra C1500

2 Answers

Changing the factory stereo need the color coded wiring diagram


you can buy,well we can,adaptor plugs to connect to the h/unit and to the wiring loom plug.normally its yellow=constant power 12v +,red=ignition feed 12v+,[some are other way round]black=earth,blue=power antennae,grey/greyblack,RF speaker,white/whiteblack,LH speaker,Purple/purple black,RR speaker andgreen/green black LR,,orange =illumination dash lights.Those are our standard colour codings,we get in New Zealand.

Jul 01, 2010 | 2001 Ford Mustang

2 Answers

97 dakota installed radio harness have power no sound


If you still haven't fixed this, look at your wiring harness. The blue wire that comes off your factory harness is the external amp in the Infinity stereo. I found this out when I hooked my Pioneer head unit up. Coming off the aftermarket stereo should be a blue wire that says remote. Hook those up and you should be good to go.

Jan 18, 2009 | 1997 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tata Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Shira

Level 2 Expert

119 Answers

old marine
old marine

Level 3 Expert

1921 Answers

Are you a Tata Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...