Question about 2004 Audi A4

Open Question

Will the transmission from a 3L 2004 Audi A6 bolt onto a 1.8L 2004 Audi A4T

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76691 Answers

SOURCE: the system detected a leak

Replace the gas cap and clear the fault code, most times this clears the issue with code P0455. If it does'nt then you will have to have test equipment hooked up by the dealer to find the leak.

Posted on Jul 28, 2008

Ad
  • 4 Answers

SOURCE: 2004 Audi A4 3L won't start

P0130 is 02 sensor bank 1 and P0150 is 02 sensor bank 2.

Posted on Jan 20, 2009

  • 79 Answers

SOURCE: Audi A6 Allroad

jack the car up saftely then take the wheels off .. then you will see the brake calipier turn the wheel towards you so the calipier is facing you . at the bottom of the calp you will see a small bolt at bottom undo this and lift prize the calp up then remove 1 pad the inside on where the piston is then put calp back down and put the bolt back in just to hold it in place then when you have done this put a large stronge screw driver in via hole in front to push the piston all the way back but make sure you do the evenly and piston goes in straight or it will get stuck same with all types of brakes. once you have done this reopen calp and take the other pad out clean all area with a wire brush and replace the new pads in place,, and retighten bolt etc , before you start the other side please make sure you pump brake peddle until it goes hard again. then do same to over side ,

hope this is a great help matdav69

Posted on Apr 07, 2009

  • 30 Answers

SOURCE: lurching start 2004 Audi A6

try the coolant temp sensor...if its getting the wrong readings then it will fuel accordingly....

Posted on Apr 14, 2009

MNfisherman
  • 11896 Answers

SOURCE: brake lights stay on all time on audi a6 2004 model

The brake switch that is located just above the brake pedal is either out of adjustment and button is stuck on and you just need to move it around and put back in place. or the switch is faulty and needs to be replaced.

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Audi A6


Search for How to Replace a Audi Head Gasket

Aug 09, 2013 | Audi Cars & Trucks

1 Answer

I need a free owner's manual for 2004 Audi A6


Hi there:
Look on eBay for an Owner's Manual or visit this links:

- audi-a6-service-manual-1998-2004
- 2004-audi-a6-owners-manual


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 20, 2012 | 2004 Audi A6 2.7

1 Answer

Hi. how do i remove oil pan of audi a6 2007 2.0 tdi? i have got all bolts off, i can move pan just a litle bit, but it feels like something is still holding it. thanks


YOU HAVE TO SUPPORT ENGINE WITH A ENGINE SUPPORT BRIDGETOOL 10-222A AND ENGINE SLING TOOL 2024A FROM THE TOP.BECAUSE YOU HAVE TO LOOSEN SUBFRAME MOUNTING BOLTS.SUPPORT THE SUBFRAME.REMOVE OR DISCONNECT THE FOLLOWING FRONT BOLTS NUMBER 2 AND 3.BOLT NUMBER 1 BOLT FROM THE SUBFRAME.SLOWLY LOWER THE FRAME.FOR MANUAL TRANSMISSION LOOSEN THE LEFT TRANSAXLE MOUNT NUT UNTIL IT IS ALIGNED WITH THE LOWER EDGE OF THE BOLT APPROX 4 TURNS.IF EQUIPPED WITH AUTOMATIC TRANSMISSION LOOSEN THE REAR BOLT FOR THE LEFT TRANSAXLE MOUNT SEVERAL TURNS THEN REMOVE THE FRONT BOLT FOR THE TRANSAXLE MOUNT.AT THE RIGHT TRANSAXLE MOUNT LOOSEN THE REAR BOLT MOUNT SEVERAL TURNS AND REMOVE THE FRONT BOLT.IF EQUIPPED WITH A MANUAL TRANSAXLE BOTH REAR BOLTS ON THE OIL PAN CAN BE ACESSED THROUGH THE OPENING ON THE FLYWHEEL TURN FLYWHEEL AS NEEDED.THEN REMOVE OIL PAN.

Apr 27, 2010 | 2005 Audi A6

1 Answer

Brake lights stay on all time on audi a6 2004 model


The brake switch that is located just above the brake pedal is either out of adjustment and button is stuck on and you just need to move it around and put back in place. or the switch is faulty and needs to be replaced.

Feb 07, 2010 | 2004 Audi A6

1 Answer

Audi A6 Xenon headlamp bulb change - UK Offside





Headlights, Removing and Installing

Removing
  • Remove front bumper.
  • Remove both Torx bolts (T30) -1-.
  • Remove interior Torx bolt (T30) using 1/4"-Torx-bit insert and extension.
NOTE: If necessary, use magnet to remove bolt.

  • Disconnect multi-function harness connectors for headlights.
  • Turn headlights -2- toward center of vehicle and remove from chassis toward front.
Installing
Installation is reverse of removal, noting the following:


  • Adjust dimension -a- via plastic bolt at new headlight.
NOTE: Determine dimension -a- at plastic bolt of old headlight, when being replaced
  • Engage headlight in area of center of vehicle in guide -2- via pin -1-.
  • Always align headlight according to contours of chassis (gap dimensions) and secure.
  • Adjust headlight after installing.
Tightening torque

Component Nm
Headlights to lock carrier 6



Repair Kit For Headlight Housing, Installing

NOTE:
  • Headlight mounting tabs that have broken off can be replaced by installing the repair kit. Complete replacement of the headlight is therefore not necessary.
  • Different repair sets are available for the left and the right headlight.
  • Remove headlight with broken mounting tab.
    • Remove remains of the broken mounting tab -1- at location marked with the arrow.
    • Place mounting tab -2- of repair set onto the edge (arrow) of the headlight housing and secure the tab with two screws -3- from rear.

Feb 09, 2009 | 2004 Audi A6

1 Answer

1995 audi a6


two bolts through middle(allen key)they are about halfway along you will see them if you look underneath near edges of number plate.....

Oct 26, 2008 | 2002 Audi A6

Not finding what you are looking for?
2004 Audi A4 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...