Question about Cars & Trucks

2 Answers

Will heater circuit sensor put car in limp mode

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,005 Answers

Very unlikely.

Posted on Dec 28, 2016

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

No year make or model. Or which heater circuit. I know of 3. None will cause limp mode. Have the codes read for the PCM.

Posted on Dec 28, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 74 Answers

SOURCE: 94 4.6 deville coolant hot,eng hot ,limp mode

pull codes from on board diagnostics turn key on not running press and hold hot button on temp and off at same time till dash lights up write down codes respond with all computer codes i will help you determine prodlem and try to fix

Posted on Aug 26, 2008

warlock61
  • 659 Answers

SOURCE: more 99 cougar problems

there is a fuse for the o2 heaters if one of the sensors blew the fuse they will all be out

Posted on Mar 01, 2009

pippall
  • 1486 Answers

SOURCE: can a flat battery on a 99 saab 95 put the car in limp mode ?

have the guy to put a new battery on the car then try it.I would not buy it if he is not prepared to do that for you.The car only goes int limp mode if you have a bad fault.I doubt its the battery i haven't come across this before just because you have a flat battery

Posted on Jun 07, 2009

  • 4 Answers

SOURCE: 98 Catera goes into "Limp Mode" after warm up.

have you check you ignition coil packs.

Posted on Jul 21, 2009

  • 412 Answers

SOURCE: Car stuck in limp mode

THE INPUT SPEED SENSOR IS LOCATED JUST TO THE LEFT OF THE OUTPUT SENSOR..ABOUT 2-3 INCHES AWAY..SAME IDEA..2 WIRE PLUG AND IT UNSCREWS FROM TRANSMISSION..YOU WILL PROBABLY HAVE TO REMOVE THE TRANS CONTROLLER AND BRACKET FOR ACCESS..I HOPE THIS HELPS

Posted on Oct 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can someone show me limp mode ln a Ford falcon gearbox


the limp mode is a program that the ECM defaults to when there is a dangerous situation occurring in either the engine or transmission
it is not a sensor or any tangible object that can be replaced
you have to have the fault codes read to determine the sensor , servo,solenoid or condition that put the ECM in limp mode

Apr 06, 2017 | Ford Cars & Trucks

1 Answer

I have a 2003 chyrsler 300m it went in limp mode codes p0700. P0340 p0344 p0430 p0888 came up cleared the codes and now it knocks.


clearing codes wont correct the problem and limp mode is designed to protect motor and transmission - p0700 is a transmission problem
P0700 Transmission Control System Malfunction p0340 is camshaft position sensor malfunction
https://www.obd-codes.com/p0340 p0344 is also a camshaft position sensor circuit problem
P0344 Camshaft Position Sensor Circuit Intermittent your p430 is a cat converter problem
https://www.obd-codes.com/p0430 and p0888 is transmission relay problem these reasons are limp mode the knock can be fuel not burning correctly or a lower engine knock can mean you damaged a piston

Nov 08, 2016 | Cars & Trucks

1 Answer

Oxygen sensor fuse blowing causing limp mode and rear brake lights to come on even with sensor unplugged.car runs for a few miles then goes into limp mode


The only reason I can think where a fuse would be used for 02 sensor is the sensor heater circuit, maybe circuit is shorted to ground?
I need year--make--model??

Apr 27, 2016 | Cars & Trucks

2 Answers

I have a 2004 dakota codes p0052 p0732 p0720 p0731 p0700. Bought non running and had a 3.7 installed got back and it jerks when taking off and won't shift out of 1st gear. Limp mode? Any ideas?


P0700 Transmission control system malfunction
P0720 output speed sensor circuit malfunction
P0731 gear ratio error in first gear
P0732 gear ratio error in second gear

May 24, 2015 | 2004 Dodge Dakota

2 Answers

P codes of P 0031, P0051, P1149. Now how do I fix them?


P 0031 A short or open in the heater circuit in the sensor
A failed O2 sensor heater

P 0051 same as above
P 1149 Air/Fuel ratio circuit 1

Your issue is not a do it yourself job, you need to take the car to a shop/ dealer



Mar 17, 2015 | 2004 Jeep Grand Cherokee

1 Answer

1997 Honda Accord 4 cylinder vtec P0715 - Input/Turbine Speed Sensor Circuit Malfunction  automatic transmission most of the time it don't want to go to the other gears stays in first gear


Sounds like your tansmission is in limp mode to protect itself.

you'll probably need to identify and correct the speed sensor problem (at the wheels or at the transmission sensor) before you'll be able to get it out of limp mode.

Feb 21, 2015 | 1997 Honda Accord

1 Answer

Ford focus 1.6 petrol gone into limp mode what can


run the fault codes to find the sensor that put it in limp mode and repair/ replace it . use that scanner to reset the CPU program to get it out of limp mode.

Sep 15, 2014 | Ford Focus Cars & Trucks

1 Answer

My car is xg300 Hyundai the code showing up are p01191 &p1193 , p0136, p0141 what are they will it cost me


Electronic Throttle System codes (P1191 & 1193), Limp Home mode & Low RPM (Detected RPM below 470). This is usually cause by either a sticking throttle plate or an intake air hose leak.

P0136 - O2 Sensor Malfunction (Bank 1, sensor 2), P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2). Either the sensor is broken, it's been unplugged, or the wiring has been damaged.

Oct 13, 2009 | 2001 Hyundai XG300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...