Question about Cars & Trucks

1 Answer

Whereis the adjustment screw for the adjustment

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 46,743 Answers

Depends on what the adjustment screw does , on what equipment for what manufacturer

Posted on Dec 27, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whereis the headlight modole located for a 2004 crown victoria


Under the dash by your right knee, you will see the black plug dealers use to plug in a scan tool. Just behind the plug is a black box, about 4inches wide by 6 inches long. It sits on top of a steel bracket. There are three 8mm screws holding it on to the steel bracket. Once you take those off, there is a plastic clip towards the back. Release the clip and pull the box out and down. There will be three wire harness plugs. Unplug those, and you're have your module.You can get a replacement module here: http://www.modulerepairpro.com/Repair-Service-To-Your-Module-MRP-LCM-0020.htm

Apr 19, 2012 | 2004 Ford Crown Victoria

1 Answer

Howtoremove radiator on1997park avenue


Drain all the antifreez, remove the upper and lower hoses, remove the clips holding the rad and pull up.

Feb 24, 2012 | 1997 Buick Park Avenue

1 Answer

Whereis the fuse for 95 lincon trunk lock


If the trunk does not pull down to lock replace the pull down switch. No fuse is used just a relay

Aug 12, 2010 | Ford Lincoln Continental Cars & Trucks

1 Answer

Whereis the dip stick and how many quarts of oil on transmission


There is no dipstick for the transmission in these vehicles. There is a check plug underneath the car, just a couple inches above the transmission pan. You must have the car running in park, at normal operating temperature, and pull the plug. The fluid should be level with the check hole.

To fill, run the car in park, pull the plug, remove the red cap on top of the transmission and fill until it pours out of the check plug.

It will take 6.9 quarts of tranny fluid.

If you have any more questions dont hesitate to ask!

Mar 29, 2010 | 2006 Saturn ION

2 Answers

No brake lights or signals


check your fuses you also have a master fuse that controls these lights signals

Jan 24, 2010 | 1994 Chevrolet Cavalier

1 Answer

Adjust headlamps 99 contur


Headlamp Adjustment Alignment
  1. NOTE: All adjustments should be made with headlamps off and at room temperature.
    Prepare the vehicle for headlamp adjustment.
    • Place the vehicle on a level surface.
    • Before aligning the headlamps, check them for faulty lenses, reflectors and blackened bulbs, and install new components as necessary.
    • Check the tire pressures and correct as necessary. For additional information, refer to Section 204-04 .
    • The vehicle must be unloaded with the exception of a tool kit and spare tire. The fuel tank should be half full.
    • Bounce the vehicle several times both front and rear or roll it a few meters so that the suspension settles.
  1. Locate the headlight adjustment screws.
    1. Vertical adjustment screw.
    1. Horizontal adjustment screw.
    2. fff6f56.gif
  1. Adjust the horizontal headlamp screw until the Horizontal indicator aligns with the "0" reference mark.
    1. Horizontal adjustment screw.
    1. "0" reference mark.
    2. 44b5acc.gif
  1. Adjust the vertical headlamp screw until the bubble is centered.
    1. Vertical adjustment screw.
    1. Bubble level indicator.
    2. fa71983.gif

Jul 04, 2009 | 2000 Ford Contour

1 Answer

Whereis my fuel filter located for 1989 D-50 2000cc, 5-speed,2 wheel drive pickup?


Hi I 86 Ram has a fuel filter right above the drivers side rear tire .

Jul 01, 2009 | 1986 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...