Question about Cars & Trucks

Open Question

Lil rider 80-FS802 wouldnt charge. Just bought for grand daughter and it wouldn't charge. There's a black wire with an eyelet connector but no instructions where it goes.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lil rider 80 kb901


with the rapid of developing, more and more plastic generated. how can we do with these so many wastes. tires, plastic rubber??? http:www.doinggroup.com/

Dec 25, 2013 | Cars & Trucks

1 Answer

Lil rider 80-kb901


The most common cause of a non-starting car is the battery. It is either weak, (low voltage) dead, (zero voltage) or has bad connections. (corroded or loose) I will assume you have a fully charged battery with good connections. (both to battery and starter relay)
If you remove the starter switch lead (small wire) from the starter relay and apply +12v from the battery to its respective prong or lead on the relay, and your starter cranks, your starter switch is faulty. (not to be confused with your key switch). If you jump the two large wires together on the relay and it cranks, then the relay is faulty. If you jump the two large wires together and nothing happens, then starter is faulty, or wires to starter are loose or broken. Picture of starter switch prong on the relay is pictured. NOTE: sparks are to be expected, so don't be too scared.

Dec 16, 2013 | Cars & Trucks

1 Answer

Engine misfiring


Had same problem with my 2002 Silverado. Took 2 month to find problem. Wires at wiring clip on valve covers that control each coil were taped to tight and the wires are so small they were braking apart.Wiggle the wires and see if the engine smooths out-runs rough-smoothes out-runs rough.Had to cut wires from connectors and wire direct. ran great for a couple of months than started again. jiggled wires and found a couple more acting up.Cut from connector and wire direct runs great again.I only have 2 wires left in original connector. The black ground wire I crimped an eyelet on both ends and grounded them to a bolt.

Apr 23, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

Hi, I connected my trailer to my Jeep Liberty with a U HAUL connector but I have a black wire that has no where to go ,although on the cover it says connect to battery there is no where to connect it and...


Black usually indicates a ground wire. It can be fastened anywhere to body/frame of the vehicle. You can use a self tapping screw to attach it. you can also find a ground strap already attached to the body and attach the wire to that. You'll have to search a little but you can usually find one.

The other option is to run the wire all the way to the battery. if the wire is not long enough you can splice in a longer piece of wire. You can then add an eyelet to the end that goes to the battery. remove the bolt that clamps the cable end to the battery. install the eyelet onto the bolt and then reinstall the bolt and cable end.

Jul 07, 2011 | Jeep Liberty Cars & Trucks

1 Answer

I have got the starter diconnected from my 2005 5.7 jeep gc but I cant get it out to replace it


1. Disconnect and isolate negative battery cable.
2. Raise and support vehicle.
3. Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt.
4. Remove two mounting bolts (2).
5. Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor (1) during this process, do not let starter motor hang from wire harness.
6. Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness.
7. Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud.
8. Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle.
9. Remove starter motor.

May 14, 2011 | 2005 Jeep Grand Cherokee

1 Answer

Wiring in a new starter for a 95 chev cav and not sure wires got put back where they need to be...nothing happening yet power is getting to the starter...


The starter is very easy to wire in, here is an image to help you out, and the starter should be connected like so;

1. Connection 1 should have the Pos. (+) battery cable, and all of the other wires from the wiring harness that have the large eyelet connectors on them connected to it.

2. Connection 2 should have the wire with the small eyelet connector connected to it, and the wire will be hot when the key is in the "start" position.


7a08527.jpg

Jun 05, 2010 | 1995 Chevrolet Cavalier

1 Answer

What conecting wires go where to the starter cyloyned


If your vehicle has a starter solenoid out by the battery and fender well, then I have provided an image that will assist you and it will connect like so;

1. Connection 1 should have the Pos. (+) battery cable and all of the wires with the large eyelet connectors from the wiring harness connected to it, except for the large cable that runs down to the starter.

2. Connection 2 should only have the large cable going down to the starter connected to it, and there should be no other wire connected there.

3. Connection 3 is the "S" terminal on the starter solenoid, and it is the wire with the small push on connector that is hot only when the key is in the "start" position, usually it is a red wire with a blue stripe, but that is not always the case.

4. Connection 4 is the "I" connection on the starter solenoid and it feeds current back into the ignition, and it is not used on a lot of vehicles after 1981, but if your vehicle has it it will be a small push on connector that will not have any power from it at all, and it will usually be a black wire with a white stripe, but that is not always so.


40c99d6.jpg
If the starter in your vehicle has the solenoid mounted on the starter then it will connect in a similar way, and the Pos. (+) battery cable along with all of the wires that have the large eyelet connectors on them will be connected together on the upper large terminal on the starter solenoid, and the wire with the smaller eyelet connector on it will be connected to the "S" terminal on the starter solenoid, and the "I" terminal if it even has one should not be used.

Jun 05, 2010 | 1988 Ford Taurus

1 Answer

The wires on a starter on a 1994 grand prix se 3.1l


The wire to the starter that has the small eyelet connector attaches to the "S" terminal on the starter solenoid, all other wire or wires, with the larger eyelet connector should be connected along with the Pos. (+) battery cable on the main "BAT" terminal of the starter solenoid.

Apr 09, 2010 | 1994 Pontiac Grand Prix

1 Answer

Is there a fuse the controls the charging systemon my 2003 Mercury Mountaineer


No there isn't a fuse that controls your charging system. There is the main connector that has a big eyelet that should have 12 volts at all times. Then there is a 3 pin connector and 1 of those wires should have power at all times as well. This means even with the key in the off position. Any questions let me know. Everything on the alternator is on a fusable link. Good luck.

May 05, 2009 | 2003 Mercury Mountaineer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...