Question about Cars & Trucks

Open Question

Why won't the weight on my metronome stay in place? It falls to bottom of the post and will not stay in position.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put lower baljoint back into lower leg


lower ball joints are fitted from the bottom up and are either bolted back in place or are pressed in place . I have done this pressing bit by fitting the ball joint in place and doing everything up and then placing a jack under the ball joint and raising the car so that the weight is on the suspension and ball and then I use a heavy hammer and hit the arm down which generally drives the ball joint into place.. Remember that the weight of the vehicle makes the suspension arm press down on the ball joint so it and tries to pull it up through the arm

Mar 14, 2014 | Peugeot 206 Cars & Trucks

1 Answer

Cv axle won't stay flush in tail shaft of my 1997 chrysler van


did the spring clip fall off the end of the joint

Aug 12, 2012 | Cars & Trucks

1 Answer

Parking brake light won't go off after releasing brake lever


Park brake lights normally operate by a small plunger type switch the turns off when the level or pedal is placed in the off position. Over time the spring in the lever weakens and placing the lever in the off position no longer depresses the switch. The switch can sometimes be adjusted to make better contact, or the switch bracket can be bent so the lever and switch make proper contact.

Feb 17, 2012 | 1992 Toyota Pickup

2 Answers

Piece of plastic is hanging down under front end of my wife's Beetle, she is 2 hours from home is car safe to drive?


It is the deflector shield for the bottom of the car, the car can be driven, just let her know that if she hears something really funny to pull off to the side of the road and look. I would say to just have her completely remove it, even if she needs to rip it off, because you are going to have to replace the part anyways

May 18, 2010 | 2001 Volkswagen Beetle

1 Answer

Rear passenger sliding door wont shut?


Check the bottom weather strip along the frame, it's common for passengers to knock them off it's runners and they fall down preventing the sliding door to close properly.
If it is the weather strip, place some RTV silicon to keep it in place when you re-install the weather strip back in place.
Thank you for using fixya and keep me posted, be glad to help you get your sliding door working 100% again.

Apr 19, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

Have 1999 Ford Expedition xlt. My gear indicator is messed up, When I am in drive, it shows 2, when i am in park it shows reverse.


This comes straight from the repair manual..
1. Remove the upper steering column cover.
2. Put the shifter in drive position.
3. Move the shift lever clockwise until it stops (all the way to first gear position, then move it back two detent positions to the Drive position.
4. Hang an a weight (something) with 8 pounds of weight on the lever to hold it in place.
5. Center the indicator neddle in the middle of drive position.
6. Rotate the thumbwheel on the bottom of the steering column to remove all slack from the indicator cable.
7 Install the upper steering column cover.

Jan 16, 2010 | 1999 Ford Expedition

1 Answer

How do i time my wiper blades after replacing wiper motor blades stay in vertical position when set on interrmitent


Remove the wiper arms from the drive posts. Turn on your wipers with the engine running and shut the wipers off -- this will put the wiper drive posts in the park position.

Reinstall the wiper arms so the blades are about an inch above the bottom of the windshield.

Charlie

Aug 22, 2009 | 2001 Chevrolet Monte Carlo

1 Answer

Steering column in a 1999 ford explore


you need to adjust the shift linkage and neutral - park safety switch.
Cable Adjustment —Shift Indicator
  1. Remove the upper instrument panel steering column cover (04459); refer to Section 501-12 .
  1. Place the gearshift lever in the (D) position.
    • Rotate the gearshift lever clockwise until it bottoms out (first gear), then rotate two detents counterclockwise ((D) position).
  1. Hang a 3.6 kg (8 lb) weight on the gearshift lever.
  1. Center the pointer in the middle of the (D) position.
    • Rotate the thumbwheel located on the bottom of the steering column to adjust the pointer.
  1. Remove the 3.6 kg (8 lb) weight.
  1. Carefully move the gearshift lever from detent to detent and compare with the transmission settings.
    • Readjust if necessary.
  1. Install the upper instrument panel steering column cover; refer to Section 501-12 .
----------------------------------------------------------------------------------------


Digital Transmission Range Sensor
The digital transmission range (TR) sensor is located on the outside of the transmission at the manual lever. The digital TR sensor completes the start circuit in Park and Neutral, the back-up lamp circuit in Reverse and the neutral sense circuit (4x4 only) in Neutral. The digital TR sensor also opens and closes a set of four switches that are monitored by the PCM to determine the position of the manual lever (P, R, N, D, 2, 1).
---------------------------------------------

Jun 02, 2009 | 2006 Ford Focus

1 Answer

Sun Visors won't stay forward towards windshield


inside the sun visor there is a spring which is moving to side when you push down the spring pushes side so it will keep down when you want to push to the normal possition spring releces and keep to that possition any way i would like to advice you to replace sun visor.

Nov 28, 2008 | 2003 Toyota Highlander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...