Question about Dodge Ram 2500

1 Answer

I have a 2500 2013 dodge ram and i need to jump start it..i don't have the book and it doesn't have a standard battery..where is the positive terminal ? please

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,992 Answers

The cable that goes to the starter should be connected to the positive terminal. The ground cable will go to a bolt on the engine or the frame.

Posted on Dec 27, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you give a jump start to someone using a 2007 Dodge Charger?


The underhood connections can work by themselves...POS to POS, and NEG to NEG...sometimes dirty/weak connections do not allow the power to transfer fully from the underhood connections...if this is the case then you need to connect directly to the battery in trunk for full power charge...again POS to POS, and NEG to NEG...hope this helps

Jun 09, 2015 | 2007 Dodge Charger SE

2 Answers

1998 ram 1500 3.9L just clicks no start


try cleaning the battery terminals first...after that you may need to jump start vehicle...if it runs remove the red power cable-if it stops you have an alternator out..if not replace battery.

Nov 02, 2014 | 1998 Dodge Ram 1500 4WD

1 Answer

It wont start, just makes a clicking noise. put new battery cables on, new starter, new cylinoid. tried to jump start it, wont jump start either


Clicking noise usually means a bad connection at the battery terminal. It can also be a bad connection at the starter or solenoid.
Re-clean and tighten battery cables,and if that doesn't do it,re-tighten starter connections.Don't overtighten as copper-bronze studs can break easily.If your Ranger is standard shift (4 or 5-speed), don't get under the car or in front of it without the battery cables disconnectede or the shifter in neutral,as any current you inadvertently send thru the starter can engage it and run you over or knock the vehicle off jackstands or blocks. don-ohio

Oct 13, 2011 | 1992 Ford Ranger

1 Answer

How to jump start dodge magnum, my battery is dead


It's pretty simple. In mine, there is a positive terminal under the hood with a red " " cover; this is where the positive cable goes. On the body of the car, near the positive terminal, there is a tab that sticks out (this is where the negative cable goes). Hook the cables to a good battery; wait a few minutes and start your car.

Sep 07, 2010 | 2005 Dodge Magnum

1 Answer

Jump Start


The positive terminal of the battery post is larger than the negative terminal ,so put your reading glasses on and have a look .

Dec 22, 2009 | 2002 Dodge Intrepid

1 Answer

Please tell me where are the positive and negetive ends of the battery for a jump start, my batttery is dead Dr.S.V.Anand


If you can locate the battery, telling the positive from the negative terminal easy.

Inspect the terminals closely; the positive terminal has a 'plus' (+) sign near it. This terminal is also larger than the other (usually).

Similarly the negative terminal has a 'minus' (-) near it.

Also visit this page for more information on jump starting.

Dec 22, 2009 | 2002 Dodge Intrepid

3 Answers

How to hook up jumper cables to a 1998 dodge stratus


negative to black either battery terminal or a good ground and red to positive battery terminal

Oct 09, 2009 | 1998 Dodge Stratus

1 Answer

Cps


Did you reset the computer after you replaced the crankshaft position sensor?

If you have,it may just be the connectors on the ECM.

If not,try this first.

To reset your engine codes:
Remove the negative terminal of your battery.
Turn your ignition key to START and hold it there for about 15 seconds.
Turn your ignition key to OFF and remove it.
Reconnect the negative terminal of your battery.
Test the vehicle.

Dec 29, 2008 | 2000 Dodge Dakota Quad Cab

1 Answer

1989 dodge ram 50 2.6l won't start after jumping other day, fuse?


Greetings!

When the battery terminals were replaced, be sure to check that all the wiring was correctly installed. (Pos+ to Pos+ and Neg- to Neg-, etc.)

Sounds like something got missed and the ignition system is not working... be sure to check the main fuses and replace any that are blown.

Cheers, Jay

Dec 11, 2008 | 1989 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...