Question about 1990 Nissan Pulsar

1 Answer

I have a 1990 nissan pulsar and the ECM light keeps coming on I also have to fill my radiator up every time i drive it because its heating up and stinks if i dont. also when i stop at the lights it cuts out whilst idoling. and sometimes doesnt start back up until cooled down was just wondering if anyone could help tell me whats wrong with it iv replaced the thermostat.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 467 Answers

The this ckeck to see that she gasket is not blown, check your radiator and fans

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi there I'm looking for some advice I have a Nissan pulsar 2000 no heat from the heater and car keeps overheating while driving I be flushed the radiator and heater core, replaced the thermostat


Crazy but have you put thermostat back in correct way? If so sounds like an air blockage. Fill radiator, leave cap off, put internal heater on hot and run engine until water is fully hot. Both top and bottom radiator hoses are hot. Sometimes therenis a bleed screw near the engine compartment bulkhead that needs opening to let trapped air out. If you have drained and refilled system and it only happened after that guarantee air lock. Good lick, let me know how you went plead.

Jun 26, 2016 | Nissan Cars & Trucks

1 Answer

I have a 1990 Nissan Pulsar and the ecm light came on.....what does this mean???


Hello,

This check to see that gasket is not blown, check your radiator and fans.
Thanks

Jun 21, 2011 | 1990 Nissan Pulsar

1 Answer

Ecm light is on? and car runs a bit like choke is not on wen driving slow? i will put some more oil in so was also wondering if its ok just to get some the the local gasa that is for a car that age(1990...


Hello and welcome to FixYa!

It's just ok to get motor oil on the local gas station. You may need to have an engine tune up to get the car back to it's normal operation. First, you may need to replace the ecm and then try to replace the spark plugs.

Hope this helps and thank you for using FixYa! Have a good one!

Apr 11, 2011 | 1990 Nissan Pulsar

2 Answers

Nissan pulsar 1992 N14


no its usually always located right off the radiator hose to regulate the heat and pressure. there is a good chance the part store gave you the wrong one

Feb 22, 2010 | 1990 Nissan Pulsar

1 Answer

ECM light on the dash


it means go to yahoo and find out how to do a code search then get the codes
and explanation and cross ref it

Jan 28, 2010 | 1990 Nissan Pulsar

2 Answers

Nissan Pulsar 1992 is overheating when I travel at 100 kmh and air con is on. It seems to running fine at lower speeds. When we turned air con off the temp did still rise but at a slower rate. Took it to...


Check for collapsing radiator hose on suction side of waterpump when motor revs raised above idle.
Check collant resevoir pressure cap is serviceable,
Check coolant system is properly filled - carry out any bleed off procedure specified to clear any air locks.
Check condition of radiator core:-
1) for blockage of air flow to (bugs/grass etc),
2) and internal blockage to coolant flow,

Replace the thermostat, if all above ok.

Oct 07, 2009 | 1990 Nissan Pulsar

3 Answers

Pulsar N13 instrument cluster no TRIP or OD


the common faults with most n13 pulsar dash clusters come from the rear circuitry where theey are all running to their respective gauges . heat and time finally get to the circuits and they let go causing a very small crack in the line causing no voltage to the gauge. easy to fix with a soldering iron and lots of patience .. good luck

Mar 15, 2009 | 1990 Nissan Pulsar

2 Answers

Nissan Pulsar three warning lights on at the same time.


Sounds like your alternator may be getting ready to check out. Have your battery and charging system tested by a dealer or shop.

Jan 10, 2009 | 1990 Nissan Pulsar

1 Answer

1991 pulsar speedo


speedo went to zero km, indicators in dash work opposite, taco isn't working either.

Jul 03, 2008 | 1990 Nissan Pulsar

Not finding what you are looking for?

Open Questions:

See all 1990 Nissan Pulsar Questions

1990 Nissan Pulsar Logo

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...