Question about Nissan Cars & Trucks

Open Question

Nissan 1400 idling - Nissan Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 nissan 1400 champ shakes the engine on idling and cuts off.secondly its not accelarating and making some sqicking noise in the engine.


Have you checked for any vacuum leaks ? Have you done a complete and proper tune up ? Any codes in ECM or an engine light on ?

Dec 07, 2016 | Nissan Cars & Trucks

1 Answer

Nissan 1400 champ shakes the engine and cuts off on idling.when driving its making some sqicking noise and not accelarating


is it running the stock engine
or is something else in the engine bay

if still carby -- old school
check float and vacuum
timing and points gap

squeaking noise
water pump
drive belt loose or an alternator bearing
if manual gearbox
clutch throw out bearing

26389082-f1p2i1ur51egwcadgrrn13x0-3-0.jpg

26389082-f1p2i1ur51egwcadgrrn13x0-3-1.jpg

Dec 07, 2016 | Nissan Cars & Trucks

1 Answer

I drive a Nissan 1400 Bakkie its doesn't want to hold idling what czs that


that could be the needle and seat in the carburetor is worn and needs to be replaced. The needle and seat is there to set float level and regulate fuel supply

Aug 12, 2016 | Nissan Cars & Trucks

1 Answer

My nissan 1400 carburetor dont want to idle when i start it up when i close the top of the carburetor with my hand then it idles and i can feel its sucking a lot of air...what can i do to fix it


check adjust the float level
check fuel pump pressure
check that the idle circuit shut off solenoid is operational
check for blockage in the idle circuit
By putting your hand over the carby you are in effect creating a vacuum in the carby that is sucking fuel into the manifold through which ever circuit is available
May be a carby over haul would be in order

Feb 17, 2016 | Nissan Cars & Trucks

1 Answer

I opened up my 1400 nissan bakkies carburetor to service it and i am not sure where all the differentjets must go


In general there are fewer ways to adjust the newer carbs than the vintage carbs of the past. Often the vacuum at low idle is the problem and you should check a vacuum port on the intake with a Vacuum gauge. Sometimes an EGR valve does not shut completely and the engine struggles at idle. If you find that vacuum is adequate, you can adjust the air mixture screws to provide the highest vacuum reading and then crank them in until the vacuum falls less than 1 inch. It might be beneficial to run the engine and spray a water mist from a hand powered spray bottle around the seams of the intake and carburetor. Also spray any vacuum solenoids or lines. You will notice a change in RPM if there is a leak. You may have a fuelpump problem A clogged fuel filter or low pressure can affect how the caricon1.png idles. Please rate my info.

Jan 21, 2014 | 2007 Nissan 1400 Bakkie

1 Answer

I have a 1999 nissan frontier with a 3.3 automatic 4x4. At idle the rpms are at about 1200 to 1400. At 60 mph the rpms are at 3200. Is this normal or is there something i can do to fix this?


There is no connection between the idle revs and revs at speed .The revs for 60 mph sound about right but the idle revs are controlled by the idle speed sensor and various other sensors Have the fault codes read Replace the faulty units with
genuine one because most aftermarket units are not set for OEM cpu units and are not completely compatible.

May 05, 2013 | Cars & Trucks

1 Answer

How do I set the timming on a 1400 Nissan sentra 1998 model


This is for a 1998 nissan sentra 1.4 engine, start engine and allow to reach operating temp.then turn engine off and disconnect throtle postion sensor connector.

With tps sensor disconnected start engine and increase idle to 2000 rpm three times then release and allow it to idle.

now check timing, timing should be at 6-10 degrees BTDC. adjust as needed then turn key off and reconnect tps .
Good day.7_15_2012_4_06_52_pm.gif7_15_2012_4_07_06_pm.gif

Jul 15, 2012 | Nissan Sentra Cars & Trucks

1 Answer

Nissan 1400 model 2008 `over heating when idling


This can be caused by a number of issues.here are the top ones I know about1. not enough fluid in cooling system2. leak [causing #1]3. low pressure caused be a bad pump, blocked of faulty thermostat.

Mar 24, 2012 | Cars & Trucks

1 Answer

I recently changed the sparks plugs on my 2007 Nissan Versa and now I am getting random idle problems while my car is in park. The car will idle from 1400 rpms them all of a sudden jump up to 2100 rpms and...


If your check engine light is on have it scanned for fault codes. Also check to make sure you don't have a vacuum leak, you could of pulled a hose loose accidently when you changed your plugs.
Signals from the oxygen sensor, and/or a bad throttle position will also cause engine surge.
Good luck, i hope this helps.

Jun 28, 2011 | 2007 Nissan Versa 1.8 Sl Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...