Question about 2003 Nissan Xterra

1 Answer

2003 Nissan Xterra 3.3L stalled out 3 times while driving now won't restart. Replaced fuel pump, distributor cap and rotor button, still won't start. Any suggestions?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 45 Answers

Check your crank sensor

Posted on Dec 27, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got water in my gas IN my 2003 Nissan xterra change distributor cap plugs and rotary button and it's too bad what do I need to check next


Start by draining fuel from tank, if filled with water! And put fresh fuel back in. God-Bless! Depending on the amount of water in the tank, you may want to leave it empty for a while so that it can dry out.

May 23, 2015 | 2003 Nissan Xterra

1 Answer

2000 infiniti QX4 3.3L (engine has a distributer) stalls out especially when revved from idle. Also won't start or very difficult to start, haven't been able to get it to start for a couple days...


pull one ignition cable out of cap just enough to see the tip of connector and crank it, a spark should jump from cap to tip of wire. no spark means you need the whole distributor replaced. buy it from nissan or infiniti dealer, it comes with cap rotor installed and 12 mo 12k mile warranty, no matter who installs it. dont waste time with aftermarket rebuilt distributor, those are not reliable. https://parts.infinitiusa.com/

Apr 06, 2017 | Infiniti QX4 Cars & Trucks

1 Answer

2000 Nissan Xterra, v6 4x2 automatic. have a problem had code po325, and po306 come up, the car will not start. changed the spark plug, distributor cap and rotor. the xterra trys to turn on but it sounds...


You got a timing chain
Injector cleaner,in my opinion is a waste of money
PO306 could be a missing coil on cyl #6,still should start
PO325 Knock Sensor-most likely okey
Plugs,cap and rotor,will not prevent it from starting,it used to run with old parts, before the current problem!

I suggest you make sure you got the plug wires on correctly and number them with a ball point pen,on both ends.
Make a diagram of the dist cap wire locations.
Check out the TPS Sensor and make sure you have all intake ducting in place. You need the MAF Sensor in the system to run have it run
Have you checked fuel pressure? The pump may be going bad

Nov 05, 2010 | 2002 Nissan Xterra

1 Answer

Starts fine & stops in 3-5 minutes or driving in 1-3 miles.


Did you replaced your whole distributor or just the cap and the rotor? Have you check the pressure on you fuel line it could be your fuel pump.

May 16, 2010 | 1993 Plymouth Colt Vista

1 Answer

'95 nissan quest stalled at a stop. Will not start, only cranks


I worked on a '93 Quest last year. Couldn't find out why it wouldn't start. It was the distributor shaft not held onto its rotating gear. The roll pin had come out of the gear on the end of the distributor shaft. When the distributor cap was off, the rotor was turning with the shaft while the engine was cranking. So I thought that was okay. But when I put my finger on the rotor and it stopped turning, that is when I found out the problem. It's a stretch, but maybe the techs missed it. Take the cap off, and if you can spin the rotor either way just by hand, the distributor gear has come loose.

Looks like they really covered a lot. I suppose next they will you to replace the ecu. Good luck.

Oct 21, 2009 | 1995 Nissan Quest

1 Answer

I have a 93 mercury topaz that stalls while driving


if it only stalls hot relace the ign module on distributor

Oct 05, 2009 | 1993 Mercury Topaz

2 Answers

My 2000 nissan xterra just quit it turns over but that is it


The fuel pump died out .
Replace the fuel pump , sometime they give no warning .

Good Luck

Apr 18, 2009 | 2001 Nissan Xterra

2 Answers

Cranks but won`t start will start with starting fliud for a few


fuel problem then .either a plugged fuel filter or the fuel pump is not working .. if you were to shoot a little fuel into the throat of the throttle body or air cleaner area you say it will run .? if so you are not getting fuel up to there . sounds like maybe a possable pump . always replace cheapest thing first like filter .. thanks Jerry holler if you need more.

Jan 30, 2009 | 2003 Nissan Xterra

Not finding what you are looking for?
2003 Nissan Xterra Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...