Question about Cars & Trucks

Open Question

There are only two marks on the seal plate. which position must the pick up sensor point

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost45
  • 1280 Answers

SOURCE: 01 elantra, when the cam sprocket marks are

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Nov 04, 2009

  • 831 Answers

SOURCE: How do i position crank sensor plate at rear main seal housing on a 1.4 bby polo engine 2008 model

It should have dowels so will only fit one way

Posted on Dec 01, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove distributor on 1984 monte carlo 305 v8


bring engine to top dead center #1 with the timing marks. remove distributer cap and note position of rotor direction and mark on the distributor housing were the rotor is pointing. also mark the position of the distributor mark to a position on the motor, then unbolt the distributor holding bolt and remove. pull up on the distributor and note which way the rotor moves as you pull the distributor out. again mark where the rotor is pointing when the distributor is out. the reason for the marking of rotor position and distributor position is so when you reassemble you line up the marks to get it into the proper position when the distributor is back in place. then you have to check the timing and set. as far as the pickup coil remove the distributor gear lock pin remove the gear and remove the distributor shaft to replace the coil. reassemble in reverse order.

Aug 11, 2014 | 1984 Chevrolet Monte Carlo

1 Answer

How to remove the pick-up coil from the distributor. 1989 GMC 1500 4X4


The distributor does have to be removed and dis-assembled in order to replace the ignition pick-up coil/stator, and if the pick-up coil/stator is faulty then the distributor should be replaced because the distributor will come with a new pick-up coil/stator and the old distributor will have to be removed anyway and in the long run it will actually save money from not having to pay a mechanic to remove and dis-assemble the distributor to replace the pick-up coil/stator, however most of the time it is the ignition module inside of the distributor that is faulty.




When the engine is at TDC (Top Dead Center) is the ignition rotor pointing to the #1 position on the distributor housing as described below?



The engine should be set on TDC (Top Dead Center) with the distributor cap removed, and there is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. (Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing)

This static timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.



If the engine is at TDC and the ignition rotor does not point to the #1 mark on the distributor housing, then loosen the hold down bolt to the distributor and turn the distributor until the rotor is pointing to the #1 mark on the distributor and then tighten the distributor hold down bolt.


6_24_2012_9_32_16_pm.jpg

Jun 24, 2012 | GMC K1500 Cars & Trucks

1 Answer

Need to know timing marks


REMOVAL
1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt. Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.

INSTALLATION
1. Install tensioner pulley. Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
If existing timing belt is being reused, install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order.
6. Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
Do not add additional tension.
8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque:28~38 lb-ft (38~51 N·m, 3.9~5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on seal plate.
11. If they are not aligned, remove timing belt and start process from tensioner installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys. If deflection is not correct, repeat from tensioner installation.
Deflection pressure:22 Ib. (98 N, 10 kg)Deflection:0.39~0.50 in. (11~13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque:5.8~8.0 Ib-ft (7.9~10.7 N·m, 0.8~1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
15. Install water pump pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
16. Install generator belt and adjust the tension.
17. Install P/S and/or A/C drive belt and adjust the tension.
18. Connect negative battery cable.

INSPECTION
Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt.
1. Replace timing belt if it is contaminated with oil or grease.
2. Check timing belt for uneven wear, fraying, peeling, cracking and hardening. Replace timing belt as necessary.
3. Bend timing belt into a "U" shape as shown in figure. Distance "A" must be at least 1.0 in (25 mm).
4. Inspect both idler pulley and tensioner pulley for uneven wear and smooth bearing operation.
5. Inspect camshaft pulleys and timing belt pulley for broken teeth or damage.
Replace any component that shows damage, excessive wear, or that appears prone to a possible failure.

Feb 26, 2011 | 2002 Kia Spectra

1 Answer

1999 silverado 4.3 cranks but no start can hear fuel pump, swaped out coil and crank sensor w/ known good parts no change, engine did start once after coil was changed ran rough and stalled and wont...


First check to see if full battery voltage is even getting to the "Pos" (+) positive side of the ignition coil when the key is in the "Run" position, and also that full battery voltage is getting through the "Pos" (+) or positive side of the ignition coil and over to the distributor ignition module

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

To replace the distributor follow this procedure;

The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This "static" timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

Removal;

1. With the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing indicating the number one position.

3. With the engine on top dead center the ignition rotor should be pointing to the number one mark or notch that is on the distributor housing, Then make a reference mark of the position that the ignition rotor is pointing to (out on the engine or firewall) and the more precise you mark the position, the easier the installation of the new distributor will be. This will be reference mark #1.

4. Remove the distributor lock down bolt, (the lock down clamp will most likely be attached to the distributor and if so it should not be removed from the distributor) then slowly lift up on the distributor about three inches and note the direction that the ignition rotor turns, and when the ignition rotor stops turning then mark the position that the ignition rotor is pointing to (out on the engine or firewall) and then lift the distributor striaght up and out, and remove the gasket or any left over gasket material from the intake manifold. The more precise you mark the position the easier it will be to install the new distributor and an assistant might be helpful. This will be reference mark #2

Once the distributor has been removed it is important that the engine does not get cranked over by the starter or the crankshaft turned at all, or the reference marks will become useless.

Installation;

Be sure that the new distributor is complete with a new module and that there is a new gasket in place on the distributor.

1. Lower the distributor with gasket down into the distrbutor well and align the ignition rotor with the #2 reference mark and when the distributor gear engages the drive gear on the camshaft then the ignition rotor should turn to the #1 reference mark as the distributor sets all the way back down flush on the intake manifold.

2. Install and tighten the lock down bolt, and If the distributor is properly installed then the ignition rotor should be pointing to the #1 reference mark and the #1 position on the distributor housing with the engine on top dead center.

Replace the distributor cap and connect the spark plug wires, and see if the engine will start, if the engine does start and the check engine light does not come on (assuming that it was not on before) then the distributor is properly installed and there is no further timing requirements.

Let me know if you require any further assistance.



a4e111e.jpg

71a37c7.jpg

91bcf9e.jpg

Jul 31, 2010 | 1999 Chevrolet Silverado 1500

3 Answers

Where is the cam position sensor located on a 98 1500 chevy p/u5.7


Camshaft sensor, in your truck it's call distributor pick-up assembly, sit in the distributor assembly, will be the connector with three wire's, to replace distributor will have to come out, before remove distributor out, remove cap and make a mark some where, where the rotor is pointing to, so when you put it back in the rotor points where the mark is at, or you will have a hard the setting it with number one cylinder again.

Jul 09, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

How to remove distributor on a 1998 gmc pick up with 5.0 engine, do I have to mark anything or just take off bolt and pull out.


You need to mark in 2 places. With the cap off mark the position of the rotor button on the distributor housing first. Then you need to make a mark on the distributor housing that will line up with a mark on the engine itself.
When you put the distributor back in back the rotor button up before you put it in because the cam gear will turn it ahead as it seats. For example, if the rotor button is at 3 o'clock then back it up to 1 o;clock.
Don't force the distributor down at the end because you can damage the end that drives the oil pump. Fidle and wiggle it as you push and it should line up and drop onto the oil pump. Also DON'T turn the engine over while it's out or you will have to retime the engine. Hope this helps.

Jul 03, 2010 | 1998 GMC Sierra

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

1 Answer

Does a 1991 Dakota 5 2L have a crankshaft position sensor?


no it has a distributor here is the prodeure for the timing sensor under the cap.
  1. Disconnect negative battery terminal, disconnect distributor lead wire at the wiring harness connector.
  2. Release distributor cap retainers and lift the distributor cap off.
  3. Scribe a mark on the edge of the distributor housing to indicate the position of the rotor. Use the mark as a reference when reinstalling the distributor.
  4. Remove the distributor hold down bolt and clamp, and carefully lift the distributor out of the engine.
INSTALLATION

  1. Clean the top of the cylinder block to insure a good seal between the distributor base and block. If the engine has not been cranked with distributor removed, proceed with step 2. If the engine has been cranked with the distributor removed proceed to step 3.
  2. Position the distributor into the engine. Make sure the O-ring seal is in place on the distributor housing. Align the rotor with the mark previously scribed on the distributor housing. Engage the tongue of the distributor shaft with the slot in the distributor oil pump drive gear. Proceed to step 4.
  3. If engine has been cranked with distributor removed perform the following:
    1. Rotate the crankshaft until number one piston is at the top of its compression stroke. The mark on the crankshaft vibration damper should be in line with the "0" TDC mark on the timing chain case cover.
    2. Rotate the distributor rotor until it is positioned pointing at the number one distributor cap terminal.
    3. Lower the distributor into the engine, making sure the O-ring seal is in place. Engage tongue of distributor shaft with slot in the distributor oil pump drive gear.
  1. Install the distributor hold down clamp and screw and tighten finger tight. Install distributor cap and wires, making sure all high tension wires are firmly secured in cap towers.
  2. Connect pick-up leads and negative battery cable lead. Set ignition timing, refer to ADJUSTMENT PROCEDURES for timing adjustment

Feb 01, 2009 | 1991 Dodge Dakota

2 Answers

Valve timing


hi there,

you have a crank sensor as well, it reads from a plate that's bolted to you crank
shaft. Now if that plate is the wrong way around the sensor is not picking up movement from the crank, it could also be that the sensor aren't close enough
to take a reading... Do not put to close as the plate will damage it... you will see the plate has 3 points on it.... this happened to me and my car stood for two days!!!

Jan 31, 2009 | 2004 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...