Question about Fiat Cars & Trucks

1 Answer

Please help i need to set timing on fiat Palio 1.6. I cant see marks and i don't have the locking tool please help im stranded on the road and its raining please send me the diagram thanks god

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Fiat Master
  • 41,378 Answers

There is not help we can give . CALL A TOW TRUCK

Posted on Dec 27, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1201 Answers

SOURCE: replacing the water pump on a fiat palio 1.2 2001

Go to an auto parts store and get a haynes auto repair manual for your car, about $17.00, it shows some illustrations, but gives a step by step procedure on how to remove and install, good luck.

Posted on Feb 25, 2009

chryslertech
  • 115 Answers

SOURCE: replacing front wheel ujoint on 2001 ram dodge 1500

HUB BEARING AND AXLE SHAFT REMOVAL

  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake components from the axle, Refer toBrakes.
  4. Remove the cotter pin and axle hub nut.
  5. Remove the hub to knuckle bolts Hub and Knuckle Remove the hub bearing from the steering knuckle and axle shaft
  6. Remove the brake dust shield.
  7. Remove the axle shaft from the housing. Avoid damaging the axle shaft oil seal.
INSTALLATION
  1. Clean the axle shaft and apply a thin film of Mopar Wheel Bearing Grease to the shaft splines, seal contact surface, hub bore. Install the axle shaft into the housing and differential side gears. Avoid damaging the axle shaft oil seals in the differential.
  2. Install dust shield and hub bearing on knuckle.
  3. Install the hub bearing to knuckle bolts and tighten to 170 N·m (125 ft. lbs.) torque.
  4. Install the axle washer and nut, tighten nut to 237 N·m (175 ft. lbs.) torque. Align nut to next cotter pin hole and install new cotter pin.
  5. Install the brake components, Refer toBrakes.
  6. Install the wheel and tire assembly.
  7. Remove support and lower the vehicle. 8014d67b.gif

Posted on Feb 27, 2009

landsend
  • 1066 Answers

SOURCE: fiat ducato timingbelt problem

on the front engine pulley/harmonic balancer or in a hole on the bellhousing. 

Posted on Mar 11, 2009

  • 11 Answers

SOURCE: fitting timing belt on my fiat ducato 2.5

u probs be best getting it to a garrage because if done wrong it can cause more problems like bending pistons

Posted on May 27, 2009

  • 1 Answer

SOURCE: timing marks on a 1.9 fiat diesel palio

digram with fiat palio 1.9 disel timing belt marks

Posted on Jan 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cam timing for fiat siena 1.2 2001


There are no timing marks on this engine - the engine has to be "locked" using special engine locking / setting kit which you wil have to obtain to do the job.

I will give you the instructions to do the job for when you have the locking kit to do the job.. as follows:

Removal
  1. Raise and support front of vehicle.
  2. Remove:
      • RH front wheel.
      • RH inner wing panel.
      • Air filter assembly.
  3. Support engine.
  4. Remove:
      • RH engine mounting and bracket.
      • Timing belt upper cover,
      • AC receiver/drier (if fitted). DO NOT disconnect hoses.
      • Timing belt lower cover.
      • Auxiliary drive belt.
      • Support bracket between gearbox and cylinder block (Palio).
  5. Palio: Remove bell housing cover plate. Fit flywheel locking tool. Tool No.1.867.029.000. or equivalent commercially available.
  6. Remove:
      • Crankshaft pulley bolts
      • Crankshaft pulley
      • Spark plug leads.
      • Ignition coil and bracket.
      • Spark plugs.
  7. Fit dial gauge and adapter to No.1 cylinder. Tool No.1.860.895.000.
  8. Turn crankshaft to TDC on No.1 cylinder. Set dial gauge to zero.
  9. Ensure notch in rear of camshaft aligned as shown.
  10. Install camshaft aligning tool. Tool No.1.870.823.000

  11. NOTE: If camshaft aligning tool cannot be fitted: Turn crankshaft one turn clockwise.

Installation
  1. Ensure No.1 cylinder at TDC by turning crankshaft slightly clockwise and anti-clockwise. Use dial gauge .
  2. Ensure camshaft aligning tool fitted correctly
  3. Hold camshaft sprocket. Use tool No.1.860.831.000/001
  4. Slacken camshaft sprocket bolt
  5. Fit timing belt in following order:
      • Crankshaft sprocket.
      • Water pump sprocket.
      • Camshaft sprocket.
      • Tensioner pulley.
    NOTE: Observe direction of rotation marks on belt.
  6. Fit tensioning tool locating pegs to tensioner pulley holes -Tool No.1.860.745.100/300. Ensure tensioning tool arm is horizontal.
  7. Set weight at 70 mm mark on scale bar.
  8. Hold camshaft sprocket
  9. Tighten camshaft sprocket bolt - Tightening torque: 70 Nm.
  10. Remove aligning tool
  11. Turn crankshaft two turns clockwise.
  12. Ensure No.1 cylinder at TDC by turning crankshaft slightly clockwise and anti-clockwise. Use dial gauge
  13. Ensure camshaft aligning tool can be fitted - If not: Repeat installation procedure.
  14. Tighten tensioner nut to 28 Nm
  15. Remove:
      • Tensioning tool
      • Camshaft aligning tool
      • Dial gauge
  16. Install components in reverse order of removal.
  17. Tighten crankshaft pulley bolts - Tightening torque: 20 Nm + 90°.

Jun 26, 2016 | Fiat Cars & Trucks

1 Answer

How do iset the cam timing on a fiat palio 1600 16valve without the locking tool


Although I believe there are timing marks on this engine, the best way to check that the engine is correctly timed is to obtain a tool kit such as the Sealey VS1402. Follow the instructions provided with the kit.

Oct 14, 2014 | Fiat Palio Cars & Trucks

1 Answer

Fiat palio ignition timing


its marked on the coil
and on the valve cover
its a wasted spark system.
the coil is marked (if not sub coil)
2314

1 goes to 1 front cylinder spark.
2 goes to 2.
3 to 3
4 to 4 rear spark.
the ecu knows the order but the wires MUST be right.
#1 spark is closest to front engine pulley, (belt side)
#4 is rear.

Jul 15, 2014 | 2005 Fiat Palio

1 Answer

Timing belt snaped on fiat palio 16v how do i find the cam marks


There are special tools you need to lock the cams in the correct position. Without these it is near impossible to get the valve timing 100% right. These locking plates fit on the opposite ends of the cam boxes from the cam gears and belt by removing the blanks on that end.
I managed to borrow a set and set it up correctly. I then made my own marks on the cam gears for future reference.

timing-belt-snaped-fiat-palio-16v-find-qdbodrihfgbojyt0cxubj1mu-3-0.jpg

timing-belt-snaped-fiat-palio-16v-find-qdbodrihfgbojyt0cxubj1mu-3-1.jpg

Apr 09, 2014 | 2005 Fiat Palio Weekend

1 Answer

Want to set timing on a fiat sienna but cant find timing marks


Im afraid you do need a special set of tools for this engine - they lock the engine and time it up accurately, you cant do without Im afraid.The tool kits come with full instructions so once you have obtained one, you will be able to time it no problem.

Apr 01, 2014 | 2005 Fiat Siena

1 Answer

Fiat palio 1.2. 2001 model.Timing marks on timing belt cover


The timing marks should be on the cover. If not you will need a service manual to find where they should be OR contact a FIAT service department person.

Feb 10, 2014 | Fiat Palio Cars & Trucks

1 Answer

Torque settings for fiat palio 1.2 8v


As you have not had an answer in a long time I would recommend that you contact a FIAT service department service advisor or shop foreman and ask the questions there.

Jan 08, 2014 | 2007 Fiat Palio II

1 Answer

Timing settings for 2002 petrol 1.6 16valve fiat palio


where is timing marks fiat palio 1.6v petrol modele 2002

Feb 25, 2013 | Fiat Strada Cars & Trucks

1 Answer

Timing marks on a 1.9 fiat diesel palio


digram with fiat palio 1.9 disel timing belt marks

Oct 25, 2009 | 2006 Fiat 124

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...