Question about Cars & Trucks

Open Question

My Ready hedger Model RH 36 won't cut the Hedges The electric motor runs gut. what is the problem?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

B&D electric hedger won't start. Help Only 1 used once last year.


Check the fuse in the power plug. If you have a a test meter check that power is getting to the moter If it is check the brushes are ok, If they are you probably have a motor fault. Consult a B ans S service center for support in that eventuality

GOOD LUCK

Jun 18, 2015 | Cars & Trucks

1 Answer

I have a Lexus Rx400h, the engine won't start. the lights, including dashboard lights, aircon, radio are on, just won't go to ready and start


Can you ensure the car is in park?
Move lever to D and then back into Park and see what happens.
I have heard with this particular model, we have the environmentally unfriendly RX 330, that the batteries lack of charge may play havock with the electrics in these cars.
I religously charge my battery every six months with a smart charger so its always in peak, I also find a quick zap at the first cold snap of autumn / winter gives us trouble free motoring.

Apr 11, 2013 | 2007 Lexus RX 400h Hybrid

1 Answer

Emergency power cut now won't start


you cut cord have open circuit.your electrical cord has three wires neutral wire white wire black wires hot wire and bare wire for ground. if you cut either neutral wire or hot black wire in the electrical cord no power can flow to trimmer motor if you cut wire need to fix wire to get trimmer work again.

Dec 24, 2012 | Cars & Trucks

1 Answer

How do i remove instrument panel cluster on 98 towncar


Removal
  1. Remove the steering column
  1. Remove the passenger side air bag module
  1. Position the speed control servo aside.
    1. Remove the nuts.
    1. Position the speed control servo aside.
    gr2792a.gif
  1. Disconnect the LH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the LH bulkhead connector.
    gr2793a.gif
  1. Unclip the LH bulkhead connector from the dash panel.
    gr2794a.gif
  1. Remove the windshield washer reservoir
  1. Disconnect the blower motor electrical connector.
    gr2795a.gif
  1. Disconnect the A/C pressure cut-off switch electrical connector.
    gr2796a.gif
  1. Disconnect the in-line wiring harness connector.
    gr2797a.gif
  1. Disconnect the electronic automatic temperature control (EATC) variable blower motor controller electrical connector.
    gr2798a.gif.
  1. Raise and support the vehicl
  1. Remove the RH front wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the RH front wheel and tire assembly.
    gr2845a.gif
  1. Remove the front fender splash shield bolts.
    gr2800a.gif
  1. Position the front fender splash shield away from the dash panel.
    gr2801a.gif
  1. Unclip the wiring harness from the evaporator case.
    gr2802a.gif
  1. Unclip the wiring harness from the dash panel.
    gr2803a.gif
  1. Lower the vehicle.
  1. Lower the RH instrument panel lower insulator.
    1. Remove the pushpins.
    1. Lower the RH instrument panel lower insulator.
    gr2805b.gif
  1. Remove the RH instrument panel lower insulator.
    1. Disconnect the power point electrical connector.
    1. Remove the courtesy lamp from the lamp socket.
    1. Remove the RH instrument panel lower insulator.
    gr2806a.gif
  1. Unseat the wiring grommet and feed the wiring harness through the dash panel.
    gr2804a.gif
  1. Remove the LH and RH cowl side trim panels.
    gr2807a.gif
  1. Remove the LH and RH windshield side garnish moldings.
    gr2808a.gif
  1. Disconnect the electronic crash sensor (ECS) module electrical connector.
    1. Disconnect the locking clip.
    1. Disconnect the electrical connector.
    dr0308a.gif
  1. Disconnect the antenna cable in-line connector.
    gr2809a.gif
  1. Remove the RH ground bolts.
    gr2810a.gif
  1. Disconnect the EATC hose from the evaporator housing.
    gr2811a.gif
  1. Disconnect the RH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the RH bulkhead connector.
    gr2812a.gif
  1. Position the LH and RH door weatherstrip seals away from the instrument panel.
    gr2813a.gif
  1. Remove the tunnel brace trim cover.
    gr2814a.gif
  1. Disconnect the climate control head vacuum harness connector.
    gr2815a.gif
  1. Remove the instrument panel tunnel brace.
    1. Remove the nuts.
    1. Remove the instrument panel tunnel brace.
    gr2816b.gif
  1. Remove the LH ground bolts.
    gr2817a.gif
  1. Disconnect the LH wiring harness connectors.
    gr2818a.gif
  1. Disconnect the parking brake switch electrical connector.
    gr2819a.gif
  1. Remove the instrument panel defroster opening grille.
    1. Unclip the instrument panel defroster opening grille from the instrument panel.
    1. Disconnect the electrical connectors.
    1. Remove the instrument panel defroster opening grille.
    gr2820a.gif
  1. Remove the three instrument panel cowl top screws.
    gr2821a.gif
  1. Remove the RH instrument panel cowl side nut.
    gr2822a.gif
  1. Remove the upper LH instrument panel cowl side nut.
    gr2823a.gif
  1. Remove the lower LH instrument panel cowl side bolt.
    gr2824a.gif
  1. NOTE: Removing the instrument panel from the vehicle requires two technicians.
    Remove the instrument panel from the vehicle.
    gr2879a.gif

Mar 07, 2011 | 1998 Lincoln Town Car

1 Answer

Overheating loosing water out of the overflow . last owners must of cut the guts out of the thermostate.


It does sounds like the thermostat needs replacing.

Charlie

P.S. By the way, cutting the guts out of a thermostat would cause the enging to run cold.

Feb 27, 2011 | 2003 Suzuki Grand Vitara

3 Answers

I lost my manual for 97 mountaneer fusebox diagram


1. pwr antenna 7.5 amp 2. high mount stop lamp 7.5amp 3. lights 15 amp 4. left headlight 10 amps 5. data link connector 10 amps 6. airbag, blower motor relay 7.5 amps 7. lamp dimmer 7.5 amps 8. RH headlight, daytime running lts, fogs 10amps 9. autolamps, memory seat 10amps 10. blend door ( heater), shift lock actuator, cruise control, brake press limit, console, integrated contol panel, rear blower relay 7.5amp 11. radio, dimmer relay, inst cluster, autolamps 2 7.5 amp 12. liftgate wiper washer, front washer relay 10amps 13. brake on off switch 15 amps 14. antilock brakes 10amps 15. airbag diagnostic 7.5 amps 16. wiper main 30amps 17. cig lighter 25 amps 18. heater-a/c eatc module 15 amps 19. radio noise cap, ign coil, PCM power diode 25 amps 20. radio, powr ant 7.5 amps 21. turn /hazards 15 amps 22. turn hazards 10 amps 23. rear wiper relay, 10 amps 24. anti theft 10 amps 25. cluster 7.5 amps 26. rear window defrost, overdrive trans, backup lamps 10 amps 27. interior lighting 10 amps 28. GEM, mem seat 2 , 7.5 amp 29. radio CD changer 10amps 30. not used 31. rear blower relay, RH heated mirror, 7.5 amp 32. heated rear window switch RH heated mirror 7.5 amp 33. DRL module, RH LH daytime running lamp 15 amp 34. power antenna module, remote chassis unit 7.5 35. not used 36. not used

Jan 07, 2010 | 1997 Mercury Mountaineer

1 Answer

I need a printable image of fuse block / 97 ford windstar


your owner manual sould have fuse chart. Some fuses/ekays in enine compartment. Some in car on left side of instrument panel

in car

1d470b5.gif
Fuse Amps Circuits Protected 1 10 Power Mirrors, Anti-Theft Warning Light, Diagnostic Connector 2 5 Generic Electronic Module, Start Interrupt Relay Coil 3 5 Radio Illumination, Remote Radio Illumination, Electronic Instrument Cluster, Electronic Instrument Cluster PRNDL Illumination, Electronic Instrument Cluster Switch Module, Analog Cluster Illumination, Instrument Illumination 4 — Not Used 5 — Not Used 6 15 Rear Quarter Windows (LH and RH) 7 15 High Mounted Stoplamp, Brake Shift Interlock 8 25 Subwoofer, JBL Amplifier 9 10 Park and Turn Lamps, Side Marker Lamps, License Lamps, Stop Lamps 10 2 High Beam Indicator Electronic Cluster 11 15 Park Lamps 12 10 Remote Radio, Auxiliary Warning Lamp Module, Remote Keyless Entry (RKE) Module, Anti-Theft Controller Module, Radio Illumination 13 15 Radio, CD Disc Changer 14 5 Electronic Chromatic Mirror, Analog Cluster Indicator Lamps, Air Bag Module 15 — Not Used 16 15 Horns, Horn Relay Coil 17 15 Fog Lamps 18 25 Front Wiper Motor, Front Washer Pump, Wiper/Washer Relays 19 10 Generic Electronic Module (Pin 57), Electronic Instrument Cluster 20 25 Integrated Relay Control Module, Ignition Coil 21 10 Air Bag Module, Rear Window Defrost Relay, A/C Clutch, Temp Blend Door Actuator, Brake Shift Interlock 22 20 Rear Cigar Lighter, Power Plug 23 15 Multi-Function Switch 24 20 Rear Wiper Motor, Rear Washer Pump 25 10 Turn Signal Lamps, Instrument Cluster Turn Indicator 26 15 LH Aero Headlamp, Left and Right Trailer Stop/Turn/Hazard 27 15 Hazard Warning Lamps, Instrument Cluster Turn Indicator 28 15 Instrument Panel Cigar Lighter 29 15 Battery Saver Relay, Interior Lamp Control Relay, Interior Lamps, RH and LH Keyhole Lamps 30 25 Backup Lamps, Electronic Cluster 31 10 Rear Air Suspension 32 15 RH Aero Headlamp, Trailer Park Lamps 33 15 Anti-Lock Brake (ABS) Relay, Anti-Lock Brake (ABS) Module, Daytime Running Lamp (DRL) Module 34 30 One Touch Relay, LH Window Motor 35 15 Anti-Theft Controller Module 36 30 A/C Mode Switch 37 20 Door Lock Actuators, Memory Door Lock Relay 38 15 Heated Mirrors (LH and RH) 39 30 Auxiliary Blower Motor, Ref. Valve Solenoid 40 30 Window Motor (RH) 41 5 Autolamp Relay Coils, Autolamp Sensor 42 — — 43 — — 44 — —

Mar 15, 2009 | 1997 Ford Windstar

1 Answer

Need help with dash removal.


  1. Remove the A-pillar and cowl side Trim Panels
  2. Remove the front floor console.
  3. Depower the supplemental restraint system (SRS).
  4. Remove the instrument panel side finish panels.
  5. Remove the 2 steering column opening cover screws.
  6. Remove the steering column opening cover.
  7. Remove the 3 lower steering column cover screws.
  8. Remove the lower steering column cover.
  9. Disconnect the steering column electrical connectors.
  10. Disconnect the RH side bulkhead electrical connector.
  11. Disconnect the RH side body harness electrical connector.
  12. Remove the 2 parking brake release handle screws.
  13. Disconnect the LH side instrument panel electrical connectors.
  14. CAUTION: To avoid damage to the clockspring, do not allow the steering column shaft to rotate while the intermediate shaft is disconnected.
  15. Remove the pinch bolt..
  16. Disconnect the adjustable pedal electrical connector.
  17. Disconnect the brake light switch electrical connector.
  18. Remove the 2 LH instrument panel center brace bolts..
  19. Remove the 2 LH instrument panel center brace nuts.
  20. Remove the LH instrument panel center brace.
  21. Disconnect the transmission range selector lever cable.
  22. Disconnect the RH side bulkhead electrical connector.
  23. Disconnect the LH side body harness electrical connector.
  24. Remove the 3 ground strap bolts.
  25. Disconnect the inertia switch electrical connector.
  26. Disconnect the RH side instrument panel electrical connectors.
  27. Remove the 2 RH instrument panel center brace bolts.
  28. Disconnect the vacuum connector.
  29. Remove the 2 RH instrument panel center brace nuts.
  30. Remove the RH instrument panel center brace.
  31. Remove the cowl panel grille
  32. Remove the instrument panel bolt located under the cowl panel grille
  33. Remove the instrument panel defroster grille.
  34. CAUTION: To avoid damage to the sunload sensor and electrical connector, remove the grille just enough to disconnect the connector.
  35. Disconnect the sunload sensor electrical connector.
  36. Remove the 2 instrument panel top cowl bolts.
  37. Disconnect the antenna lead-in cable.
  38. Disconnect the RCM electrical connector.
  39. Disconnect the center ground strap bolt.
  40. CAUTION:To avoid damage to the instrument panel, an assistant is required to support the panel before carrying out this step.
      • Before removing the instrument panel make sure all electrical connector wiring is free and not hindered.
  41. Remove the 4 instrument panel bolts.
  42. Remove the instrument panel.
  43. To install, reverse the removal procedure.

Feb 11, 2009 | 2005 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...