Question about Cars & Trucks

Open Question

Garage lights stay on

Will not turn off at multifunction control board light switch

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wireguy212
  • 1627 Answers

SOURCE: does the MULTIFUNCTION SWITCH control the rear brake lights?

You need to replace the multifunction switch,the wireing to the brake lights in the rear are shared by this switch and the brake light switch and because the third one is working then it is unlikely the brake switch is defective.

Posted on Nov 14, 2009

  • 1 Answer

SOURCE: 04JeepGrdCher:Interior lights stay on and power windows dont work

I had this same problem but no sunroof on mine. there is a bundle of wires that goes into the door and if the power wire breaks and the power window lockout was pushed when it happens no windows work and the dome lights stay on on mine it happened on the drivers side it was an easy fix i took the door panel off and unpluged the harnes and pulled it through the inside of the jeep and spliced the wire back together and it has been working since.

Posted on Dec 05, 2009

  • 389 Answers

SOURCE: 1992 Ford Ranger Turn signal/Hazard light issue

Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Posted on Apr 19, 2010

  • 2926 Answers

SOURCE: Interior lights stay on. I have replaced the

It is isolated to one switch inside one of the doors. Try spraying wd-40 in each door latch area to see if this free's up the switch. If not, you have to use a volt meter and see which one is using constant voltage.

Posted on Nov 06, 2010

CarMech97
  • 427 Answers

SOURCE: CHECK ENGINE LIGHT WONT LIGHT.MUST LIGHT WITH KEY

Sounds like a crossed wiring connection somewhere, if the four-way flashers are turning on the high-beam indicator. Check all the connectors in the associated wiring harnesses for the instrument panel. Good luck!

Posted on Jan 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't the headlights turn on?


This vehicle has problems with the multifunction switch AND the hazard light switch. Try turning the switch on and move the hazard light switch back and forth up and down. If that's not it, I'd look at replacing the MFS. There is a TSB on the MFS, but typically for the brake lights not working. Look in this to go over the steps to take to diagnose also.

Sep 30, 2015 | 1999 Chevrolet Blazer

1 Answer

High mount brake light stays on after ignition is turned off


The only suggestion I can make is that the turn signal switch is defective and is shorted internally. If you disconnect the turn signal/multifunction switch under the dash do the lights go out in question?

Mar 21, 2014 | 1992 Ford F150 SuperCab

1 Answer

I have a 2002 ford windstar Es: wen the van is turn of, some times the lights inside stays on and the turning signal on the mirror, I go to drive the van and the doors signal stays on at all times and the...


the ecu runs every thing on the motor and transmission. you have a common problem with the multifunction control module . depends which model windstar . most of them are on the right hand kick panel1_27_2013_8_52_09_pm.png

Jan 27, 2013 | Cars & Trucks

1 Answer

Back brake light stay on, replaced brake switch same problem.Truck has over drive and cruies control If you take switch out of circuit the brake lights stay on the same with the turn/hazard flasher.


Your brake lights and your turn signals go through the multifunction (turn signal) switch. It is common for these switches to short internally. Partial disassembly of the steering column is required to replace it. The airbag stsyem must be disabled, then the airbag removed from the steering wheel. Then the steering wheel must be removed to access the screw in the front of the switch assembly. The rest is pretty easy... a few screws holing the lower cover of the dash, the shroud around the steering column and a few connectors to deal with. (see pictures of switch assembly below)
There are two types of these switches available for 2000 S-10. With cruise control and without cruise control. The one WITHOUT cruise control is much more expensive!


dttech_156.gif
dttech_35.jpg

Aug 06, 2011 | 2000 Chevrolet S-10

1 Answer

Driver seat belt worn half way thru .engine just started to idle high. door lights stay on,it is a 1992 4 dr hatch back w/70000 mi


I'm sorry, what is your question?

Your seat belt can be replaced - the seat belt has nothing to do with the engine idle, or the door light. The light stays on because the door switch needs adjustment or replaced or perhaps it has beenturned on by the light interior light switch that controls the dash board lights.

70,000 is not a lot of miles.

I suggest you have your vehicle tuned up aat a garage to fix the high idle and assure economical operation. That same mechanic may be able to advise you on the light and how to replace the seat belt. Your car may be running fast because of the cold weather to warm itself up. I dont know where you live.

Mar 09, 2010 | 1992 Geo Metro

2 Answers

One blinker stays on while the other blinks fast when lights are


The multifunction switch is faulty. the turn signal control.

Jul 25, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

Fog lights on all the time


Sounds like your multifunction switch (i.e. the stalk that has the fog light switch) has burned out. This is a fairly common problem and the multifunction switch needs to be replaced.

The part (as I recall) costs < $100 (about 80, I think) and takes less than half an hour to replace.

Jun 10, 2009 | 2002 Chrysler PT Cruiser

1 Answer

Fog lights came on; can't turn them off


1.At first take out the foglight's fuse before you battery is dead. (Fog lights stays "ON" even you leave the car).

2.You must replace the Multifunction control switch =(

Here is the photo of problem:
http://www.ptcruiser.fi/ptgalleria/albums/userpics/10010/normal_sumuvalokytkin.jpg

Fog lights are connected to pin 13,14.
Fog light switch is "B". Because the current is many Amps, contact surfaces are heating up.
After that the contact opening "C" is melting (made of plastic) so the fog light stays "ON".

May 11, 2009 | 2002 Chrysler PT Cruiser

2 Answers

Fog lights staying on


1st most newer car cars have a timer delay that helps light the area you are in for a couple of seconds. You may have had the knob turned all the way up on the turn signal switch. The same thing will happened if this switch is turned all the way up, the interrior light will stay on. Turn the lights on with the switch and see if the fog lights come on, do this without the car running.Trun the lights off,see if the fog lights stay on then go out after a while.if so you have a delay on the fog lights or relay. You may need to replace the relay only. Part $ 15 trace fog light wiring to relay usually under hood away from water sources.......runjoe

Jan 30, 2009 | 2002 Chrysler PT Cruiser

1 Answer

2003 Grand Marquis Headlights


New Light control moduel solved problem

Jul 20, 2008 | 2003 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...