Question about 1998 Chevrolet K1500

1 Answer

Where is the inflatable restraint instrument panel module switch on a 98 k1500 silverado

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,585 Answers

In the steering column. These are way different than today's models.

Posted on Dec 26, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the yaw sensor located on a 2008 Pontiac Torrent?


yaw-xozrttqlr3qpoa0t2tmccx0o-1-0.png 1 - Floor Panel
2 - Console
3 - Yaw Rate and Lateral Acceleration Sensor
4 - Seat Belt Pretensioner - Right
5 - Inflatable Restraint Side Impact Sensor (SIS) - Right (ASF)
6 - Rollover Sensor (ASF)
7 - Inflatable Restraint Sensing and Diagnostic Module (SDM)
8 - Seat Belt Pretensioner - Left
9 - Inflatable Restraint Side Impact Sensor (SIS) - Left (ASF)

Apr 16, 2017 | Pontiac Cars & Trucks

1 Answer

How to get the airbag light to go off on a 2007 Chevy van Express


You need to find out what code or codes are stored in the airbag control module > There are a lot of components involved in your airbag system : If you haven't had any training on these systems your best bet is take it to a ASE certified repair shop . People have been killed messing with these systems not knowing what they were doing .
The frontal SIR system consists of the following components:
?€¢
AIR BAG indicator located on the instrument panel cluster (IPC)


?€¢
Driver and passenger knee bolsters


?€¢
Inflatable restraint front end sensor


?€¢
Inflatable restraint PASSENGER AIR BAG ON/OFF indicator located on the instrument panel


?€¢
Inflatable restraint Passenger Presence System (PPS)


?€¢
Inflatable restraint I/P module


?€¢
Inflatable restraint I/P module disable switch


?€¢
Inflatable restraint seat position sensors (SPS) (left/right)


?€¢
Inflatable restraint sensing and diagnostic module (SDM)


?€¢
Inflatable restraint steering wheel module


?€¢
Inflatable restraint steering wheel module coil


?€¢
Inflatable restraint wiring harnesses


?€¢
Seat belt pretensioners (left/right)


?€¢
Steering wheel and column

Nov 22, 2015 | Cars & Trucks

1 Answer

How to get airbag module out of dash on my 98gmc 1500


Remove the instrument panel. Refer to Instrument Panel Carrier Replacement in Instrument Panel, Gauges and Console. Remove the fasteners (5) (4) that retain the inflatable restraint IP module to the instrument panel (3). Remove the inflatable restraint module (2) from the instrument panel (3). Fully deploy the module before disposal. If the module was replaced under warranty, fully deploy and dispose of the module after the required retention period. Refer to Inflator Module Handling, Shipping, and Scrapping .
Removal Procedure
Instrument Panel Carrier Replacement

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
  1. Disconnect the negative battery cable(s).
  2. Disable the SIR system. Refer to Disabling the SIR System in SIR.
  3. Remove the three relay center bolts from the underside of the wheel opening.
  4. Remove the bulkhead connector.
  5. Remove the following components from the bulkhead connector:
  6. ?€¢
    The screws from the convenience center to the cowl


    ?€¢
    The cruise control harness (if equipped)


    ?€¢
    The forward lamp harness


    ?€¢
    The SIR system harness


    ?€¢
    The relay center

  7. Remove the coolant reservoir. Refer Coolant Recovery Reservoir Replacement in Engine Cooling.
  8. Disconnect the antenna lead-in and the grommet.
  9. Remove the knee bolster. Refer to Knee Bolster Replacement .
  10. Remove the steering shaft pinch bolt.
  11. Remove the left and the right sill plate front screw.
  12. Remove the left and the right hinge pillar trim panels. Refer to Body Hinge Pillar Trim Panel Replacement in Interior Trim.
  13. Remove the brake release handle from the cable.
  14. The clip releases the handle from the cable.
  15. Remove the reaction plate assembly.
  16. Remove the tie bar.
  17. Remove the knee deflector bracket.
  18. Disconnect the 8-way column connector.
  19. Disconnect the 48-way connector retainer in order to access the two lower column nuts.
  20. Disconnect the shift cable (Automatic transmission).
  21. Remove the steering column from the vehicle.
  22. Remove the shift levers.
  23. ?€¢
    Remove the transfer case knob by pulling the knob straight up. S4WD models must be in the 4-LO range.


    ?€¢
    Remove the manual transmission shift lever (if equipped).

  24. Remove the front floor console, if necessary.
  25. Remove the left and the right lower IP pivot bolts.
  26. Remove the IP storage compartment door. Remove the IP storage compartment.
    Squeeze the compartment in order to release the compartment.
    Remove the two IP attaching bolts through the storage compartment door
    1. Remove the center support screw.
    2. Remove the three IP upper support screws.
    3. Remove the IP from the front of the dash.
    4. Disconnect the park brake lever. Refer to Park Brake Lever Assembly Replacement in Parking Brake.
    5. Disconnect the following electrical connectors as necessary:
    6. ?€¢
      The sensing and diagnostic module (SDM)


      ?€¢
      The Heating, Ventilation and Air Conditioning module (HVACM)


      ?€¢
      The 22-way engine harness


      ?€¢
      The stoplamp switch


      ?€¢
      The vehicle speed sensor (VSS) calibrator module


      ?€¢
      The clutch or brake release switches


      ?€¢
      The electronic accelerator (Diesel)


      ?€¢
      The HVAC control cables (if equipped)

    7. Remove the IP from the vehicle.
    To this point, the IP removal is complete. If the IP is being replaced or refinished.
    Remove the accessory switch(es) as necessary. Remove the instrument cluster bezel. Refer to Instrument Panel Cluster Trim Plate Bezel Replacement . Remove the headlamp switch. Remove the HVAC control assembly.
    4.1.
    Disconnect the electrical connectors.


    4.2.
    Disconnect the cables (if equipped).

    Remove the instrument cluster screws and the cluster. Refer to Instrument Cluster Replacement .
    Remove the IP storage compartment.
    Squeeze the compartment in order to release the compartment.
    Remove the IP storage compartment lamp.
    Slide the compartment in order to release the compartment.
    Remove the low coolant module (Diesel only). Remove the data link connector (DLC).
    20.1.
    Remove the one screw.


    20.2.
    Slide the DLC out.

    Remove the harness retainer to accessory switches. Remove the fuse panel and the courtesy lamp switch. Remove the ground screw. Remove the harness from the IP. Remove the jumper harness to the remote playback device (if equipped). Remove the courtesy lamp switches. Remove the side window defogger outlets. Remove the park brake cable clips. Remove both of the air outlet deflectors

Oct 03, 2015 | Cars & Trucks

1 Answer

Steering wheel airbag removal on 2006 Cadillac cts cant find bolts


There are no bolts ! it takes a special tool , there are spring loaded Fasteners .
Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
Steering Wheel Inflatable Restraint Module Replacement
Tools Required J 44298 Driver Air Bag Removal Tool
Removal Procedure
Caution: Refer to
SIR Inflator Module Handling and Storage Caution in the Preface section.
Caution: Refer to SIR Caution in the Preface section.

showgif.do?image=640349

tif.gif
Caution: A deployed dual stage inflator module will look the same whether one or both stages were used. Always assume a deployed dual stage inflator module has an active stage 2. Improper handling or servicing can activate the inflator module and cause personal injury.
  1. Disable the SIR system. Refer to SIR Disabling and Enabling .
  2. On the back side of the steering wheel are 3 openings for removing the steering wheel module.
  3. Adjust and install J 44298 into 1 of the holes.
  4. Important: Seat the air bag removal tool all the way in to perform properly.
  5. Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
  6. Repeat this step for the other 2 fasteners.
  7. Pull the inflatable restraint module gently away from the steering wheel.
    showgif.do?image=818476
  8. tif.gif
  9. Important: Note the wire routing positions on the steering wheel module connectors, the redundant control routing positions, and the horn wire routing positions for the correct assembly.
  10. Remove the connector position assurance (CPA) (4) and the electrical connector from the steering wheel module.
  11. Remove the horn contact lead (2) from the steering column cam tower.
  12. Remove the steering wheel module (5

Mar 09, 2015 | 2006 Cadillac CTS

1 Answer

2009 chevy impala left front side deployment loop resistance B0014 above threshold


the following link covers yours reqest The driver frontal loops 1 and 2 are the loops to the steering wheel air bag. The SDM(sensing and diagnostic module for the air bag) is seeing these circuits as open. There is a bullitin for problems with a loose connection for the yellow connector behind the left kick panel(right behind the e brake and hood release). I would remove the kick panel, and disconnect and reconnect the connector a couple times. See if the light goes out. Or wiggle and move the connector with the key on, as the light should go out if it makes good connection. If it does go out you need to replace this connector. Good luck.

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)
Models:2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)


This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

<A href="#ss1-2146754">
Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

<A href="#ss2-2146754">
Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

<A href="#ss3-2146754">
Diagnostic Information

DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.
<A href="#ss4-2146754">
Correction
DO THIS

Don't Do This

Test for proper connection/high resistance at connector C221 and/or C222.

DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.



Important:
The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column.
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.


  • <LI type=1>Remove the appropriate side door sill plate. <LI type=1>Remove the appropriate side hinge pillar panel. <LI type=1>Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222. <LI type=1>Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection. <LI type=1>Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times. <LI type=1>Clear the DTC and road test the vehicle. • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
    • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
    <LI type=1>Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229). <LI type=1>Road test the vehicle and confirm that the repair is complete. <LI type=1>Install the driver's side hinge pillar panel.
  • Install the driver's side door sill plate.
<A href="#ss5-2146754">
Parts Information
Part Number

Description

Qty

15306186

Connector (4-way Female, w/Leads)

1

88987998

Connector (4-way Male, w/Leads)

1 Service Airbag Have Codes Ask the GM Technician

May 01, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

How to Change an Ignition Lock on a 2004 Buick Rendezvous.


Please let me know if you have questions, and thanks for using FixYa.

Removal & Installation
  1. Disconnect the battery negative cable, as outlined in the Chassis Electrical Section.
  2. Disable the Inflatable Restraint (SIR) system. (see procedure below)
  3. Remove the steering wheel.
  4. Remove the tilt lever close out plate.
  5. Remove the retaining screw from the lower steering column trim covers.
  6. Tilt the trim cover down and slide rearward in order to disengage the locking tabs.
  7. Remove the lower steering column trim covers.
  8. Remove the retaining screws from the upper steering column trim cover.

    jturcotte_1886.gif

    Fig. Lift the trim cover in order to gain access to the lock cylinder access hole.

  9. Lift the trim cover in order to gain access to the lock cylinder access hole.
  10. Insert the Snap-On A173A bent-tip awl or equivalent, with a 3/32 in (2.5mm) tip, and 3/4 in (20mm) in length, into the access hole of the ignition lock cylinder.
  11. Turn the ignition lock cylinder to START .
  12. Use the bent tip in order to push down on the ignition lock cylinder retainer.
  13. Release the ignition lock cylinder to the RUN position.

    jturcotte_1887.gif

    Fig. Remove the ignition lock cylinder from the lock cylinder case.

  14. Remove the ignition lock cylinder from the lock cylinder case.

To install:
  1. Insert the ignition lock cylinder through the trim cover in the upper steering column.
  2. Align the lock cylinder retaining tab and the position tab with the slots in the lock housing.
  3. Completely push the lock cylinder into the lock housing.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the retaining screws to the upper steering trim cover and tighten the screws to 31 inch lbs. (3.5 Nm).
  5. Match the tab slots on the lower trim cover with the locking tabs on the upper trim cover.
  6. Tilt the lower trim cover up and slide the lower trim cover until the locking tabs snap into the tab slots.
  7. Install the lower trim cover screws to the steering column and tighten the screws to 13 inch lbs. (1.5 Nm).
  8. Install the tilt lever close out plate.
  9. Install the steering wheel.
  10. Enable the SIR system, as outlined in the Chassis Electrical Section.
  11. Connect the battery negative cable.


Disarming the SIR System

Print

  1. Turn the wheels to the straight-ahead position, then turn the ignition switch to LOCK .
  2. Remove the console accessory wiring junction block access hole cover.
  3. Remove the "AIR BAG" or "SIR" fuse from the block, as applicable.
  4. Remove the left-hand sound insulator, for access to the SIR wiring harness.

    jturcotte_1888.gif

    Fig. Driver-s side air bag connector location


    jturcotte_1889.gif

    Fig. Passenger-s side air bag connector location


    jturcotte_1890.gif

    Fig. Side air bag connector location

  5. Remove the Connector Position Assurance (CPA) device, then disengage the yellow 2-way connector at the base of the steering column.
  6. Remove the right hand insulator panel.
  7. Remove the CPA from the inflatable restraint instrument panel module connector located behind the RH insulator panel.
  8. Disconnect the instrument panel module connector
  9. If equipped with side air bags, remove the CPA from the inflatable restraint side impact module-left front connector located under the driver seat.
  10. Disconnect the side impact module-left front connector.
  11. Remove the CPA from the inflatable restraint side impact module-right front connector located under the front passenger seat.
  12. Disconnect the side impact module-right front connector.
    NOTE With the fuse removed, the AIR BAG or SIR light will illuminate if the ignition switch is turned ON at any time. This is normal and does not indicate a problem when the system is disarmed.


Arming The SIR System
  1. Be sure the ignition is in the LOCK position.
  2. Connect the inflatable restraint side impact module-right front connector located under the front passenger seat.
  3. Install the CPA to the side impact module-right front connector.
  4. Connect the inflatable restraint side impact module-left front connector located under the driver seat.
  5. Install the CPA to the side impact module-left front connector.
  6. Engage the yellow SIR connector, then secure using the CPA device for both the drivers and passenger sides.
  7. Install the sound insulator panel.
  8. Install the SIR system fuse to the fuse block.
  9. Turn the ignition switch to the ON position and verify that the AIR BAG indicator light flashes 7 times, then extinguishes. If it does not go out, troubleshoot the SIR system fault.
  10. Install the instrument panel lower extension.

Jun 30, 2011 | 2004 Buick Rendezvous

1 Answer

Where is the airbag module located in the 2000 cadillac seville


Hello: Sir, There are a total of 5 (five) modules in the Inflatable restraint system, ( airbag) I will list them, their purpose and location:
Sensing & Diagnostic Module, the main module located under the rear of center console, Driver side inflator module located left side driver seat back . driver side inpact sensor located left lower side of center left pillar. steering wheel inflator module under the horn pad in the steering wheel. passenger front side inflator module located under righ side of upper instrument panel . Right front passenger side impact module right side of passenger seat lower back. Rf passenger side impact sensor. lower part of center pillar. The left and right sensors are not modules . Note, Codes B0051 and B0053 require replacement and programming with a scanner. Hope this helps you

Oct 08, 2010 | Cadillac Seville Cars & Trucks

1 Answer

CODE B0026 HOW DO I RESOLVE? REAR DOOR LOCKS NOT WORKING, SERVICE BRAKE BOOSTER WARNING ON, AIRBAG LIGHT ON, SERVICE AIRBAG WIRNING, INTERMIT NO START. HELP MEEEE!!!!!!


The airbag connectors in behind the front kick panels have high resistance. The fix is to replace them. Here is TSB's

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:
Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)

Models:
2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)

This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

Diagnostic Information
DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.

Correction

DO THIS
Test for proper connection/high resistance at connector C221 and/or C222.

Don't Do This
DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

Important: The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column...
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.

1. Remove the appropriate side door sill plate.
2. Remove the appropriate side hinge pillar panel.
3. Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222.
4. Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection.
5. Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times.
6. Clear the DTC and road test the vehicle.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
7. Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229).
8. Road test the vehicle and confirm that the repair is complete.
9. Install the driver's side hinge pillar panel.
10. Install the driver's side door sill plate.

Parts Information
Part Number: 15306186
Description: Connector (4-way Female, w/Leads) - Qty 1

Part Number: 88987998
Description: Connector (4-way Male, w/Leads) - Qty 1


Hope this help (remember comment and rated this help).

May 07, 2010 | 2003 Chevrolet Suburban 1500

1 Answer

Electrical problem under dash How do I remove dash?


c3eadb0.gif
Instrument panel upper trim panel

dbe998b.gif
Instrument panel


  1. Disconnect the negative battery cable.
  2. Disable the Supplemental Inflatable Restraint (SIR) system.
  3. Carefully pry upward, using a small, flat-bladed tool, to remove the defroster grille.
  4. Remove the Sunload and Headlamp Auto Control sensors from the defroster grille.
  5. Working through the defroster grille opening, remove 3 upper trim panel retaining screws.
  6. Remove the heater/air conditioning vents from the front of the instrument panel by releasing the tab on each side from inside the vent and pulling out.
  7. Working through the vent openings, remove 4 upper trim panel retaining screws and remove the upper trim panel.
  8. Remove the instrument cluster.
  9. Remove the right and left A/C vent trim panels.
  10. Open the trap door in the rear of the glove compartment and remove the passenger inflatable restraint wiring connector from the retaining clip on the rear of the glove compartment assembly.
  11. Remove the 4 glove compartment-to-instrument panel retaining screws.
  12. Pull the glove compartment assembly outward enough to access the wiring connectors for the glove compartment switches. Label and detach the wiring connectors.
  13. Remove the glove compartment assembly from the instrument panel.
  14. Remove the retaining screws and courtesy lamps from the right and left sound insulators and remove the sound insulators.
  15. Remove the steering column opening filler trim by grasping at the front and rear edges and pulling downward.
  16. Remove the 4 retaining bolts and the steering column opening bracket.
  17. If equipped with full console, remove the console.
  18. If equipped with mini console, remove the radio.
  19. Remove the headlamp switch module.
  20. Remove the 2 bolts and the hood latch release.
  21. Move the driver's seat to its full rearward position.
  22. Remove the steering column.
  23. Remove the 8 instrument panel retaining screws, detach the wiring connector at each side of the instrument panel, and remove the shims at the lower mounting screws.
  24. Remove the instrument panel with the aid of an assistant.
To install:
  1. With the aid of an assistant, position the instrument panel in the vehicle.
  2. Attach the wiring connector at each side of the instrument panel, install the shims and the 8 instrument panel retaining screws.
  3. Install the steering column.
  4. Install the hood latch release with the 2 bolts.
  5. Install the headlamp switch module.
  6. If equipped with mini console, install the radio.
  7. If equipped, install the console.
  8. Install the steering column opening bracket and the steering column opening filler trim.
  9. Install the right and left sound insulators.
  10. Position the glove compartment assembly and attach the wiring connectors to the switches.
  11. Push the glove compartment into place and install the retaining screws.
  12. Place the passenger inflatable restraint wiring connector on the retaining clip on the rear of the glove compartment assembly and close the trap door.
  13. Install the right and left A/C vent trim panels.
  14. Install the instrument cluster.
  15. Position the upper trim panel on top of the instrument panel, making sure the sensors are through the trim panel.
  16. Install the upper trim panel retaining screws through the heater/air conditioning vent openings.
  17. Gently push the heater/air conditioning vents into place.
  18. Install the upper trim panel retaining screws through the defroster grille opening.
  19. Install the Sunload and Headlamp Auto Control sensors to the defroster grille.
  20. Gently push the defroster grille into place.
  21. Enable the SIR system.
  22. Connect the negative battery cable.

Dec 01, 2009 | 1995 Cadillac DeVille

1 Answer

Horn not working due to clock spring


The part is still available from GM. It is part # 94857236.

You must be careful when replacing the clock spring as it controls the SRS system.
You will need to remove the steering wheel airbag and and the steering wheel itself.

Important: Perform this procedure in order to prevent deployment of the air bags from the reserve energy supply power.

  1. Remove the CIG and IGN Fuses from the junction block (1), which is located near the base of the steering column.
  2. Remove the lower steering column trim cover.
  3. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  4. Remove the key from the ignition switch
  5. Release the inflatable restraint steering wheel module coil connector locking mechanism.
  6. Disconnect the inflatable restraint steering wheel module coil connector C3
  7. Remove the Instrument Panel (IP) compartment (2)
  8. Release then unlock the IP module connector (1).
  9. Disconnect the IP module pigtail.
  10. Release and unlock the driver and passenger seat module connectors.
  11. Disconnect the driver and passenger seat modules.42de416.gif0276398.gif6983629.gife094e58.gif

Jul 16, 2009 | 1998 Chevrolet Prizm

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...