Question about Cars & Trucks

1 Answer

Wh at causes my lift lock not to lock on my srx 2005 cadilac because all my other doors lock using my keyless remote?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

The actuator for that door.

Posted on Dec 26, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me why my liftgate will not lock using my keyless remote entry.all the other doors lock my vehicle is a 2005 srx cadillac


If it locks when using the manual switch inside the car, the problem is probably your remote. If not, your lock solenoid in the lift gate may need to be replaced.

Dec 24, 2016 | 2005 Cadillac SRX

1 Answer

How to replace struts on a 2005 cadilac srx


need a special tool strut cartridge remover, take off two plates on top on both sides of car. Put jack under one wheel jack up and then take out one strut at a time.

Jul 03, 2014 | 2006 Cadillac SRX

2 Answers

Suddenly, my automatic door unlock button on remote for my 2005 Chevrolet Equinox will not unlock doors and alarms goes off if I manually open driver's door and don't start car right away. Wh


I tried replacing battery in my remote. Sometimes it work and sometimes it doesn't. I think it could be a wiring problem in the remote. I know it's a major paun having to hurry up and put key in ignition befofr alarm starts going off.

Oct 30, 2012 | 2005 Chevrolet Equinox

1 Answer

I own a 2005 Ford Five Hundred and I am trying to get my keyless entry to work.


I assume you are trying to program the remote. Here are the instructions. Your question is very vague.
1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle
to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will
cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

Oct 20, 2012 | Cars & Trucks

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Would anti theft cause car to quit


Sounds like a bad ignition switch have ur body control module checked for codes if u have a B2960 and or B3033 then replace the ignition switch.

SECURITY
If your vehicle has the remote keyless entry system, this feature allows you to select the method used to arm the vehicle's security system. When SECURITY appears on the display, press the reset button to scroll through the available settings:
* RKE (Remote Keyless Entry) (default): The content theft-deterrent system will arm when the lock button on the remote keyless entry transmitter is pressed or when the power door lock switch is pressed.

* PASSIVE: The content theft-deterrent system will arm itself 60 seconds after the ignition has been turned off and all of the doors have been closed.


Hopd this help (remember comment and rated this).

May 04, 2010 | 2005 Chevrolet Cobalt

2 Answers

Honda Element doors auto lock when keys in ignition.how to stop?


Actually, some other Honda models have a similar function, actuated by a combination of drive gear and road speed, but no Honda Element was ever factory equipped to automatically lock the doors when running. Its's a feature provided by some aftermarket keyless entry and/or security systems.
The Honda Elements' normal operation re-locks the doors if they are remotely unlocked, but a door isn't physically opened within 15-30 seconds. This is only supposed to happen when the keyless remote receiver signals the multiplex control unit to open the drivers door.

Open the drivers' window, take the battery out of the remote control fob, and see if the problem persists. If so, unplug the connector of keyless receiver module., and test again. If there's not a good electrical connection on all 4 pins of the KRU, or if the KRU is bad, that could cause your problem. Alsocheck G501. .

Aug 19, 2009 | 2005 Honda Element

2 Answers

Nissan Murano 2005 SL keyless entry remote programing, got a used remote, how can I program it?


Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Aug 06, 2008 | 2005 Nissan Murano

6 Answers

Keyless entry stopped working on 05 cobalt now i have to unlock door with the key and when i do that the alarm goes off. Help


Lock all the doors from the inside (with all the doors closed), unlock your driver's door by manually lifting the lock, then press it back down after you are out - this will prevent the alarm from sounding when you use the key to unlock the door.

Aug 02, 2008 | 2007 Chevrolet Cobalt Coupe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...