Question about 2007 Ford Freestyle

1 Answer

How to install a starter 2007 ford freestyle

Location of starter, any special tools or instructions

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 1,985 Answers

If you're going to keep this vehicle, and intend on doing some of the maintenance yourself, go to an auto parts store and purchase a Haynes or Chilton repair/service manual. The $15-$20 investment will provide you most all the answers you need regarding proper steps and tools needed.

Posted on Dec 26, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No power in ignition...

If you have another set of keys with a FOB, try it. The anti-theft will reduce voltage to the starter to prevent thefts. If the anti-theft is not reading the key that is inserted, you will not get battery voltage to the starter.

Sep 18, 2014 | 2005 Ford Freestyle

1 Answer

How to remove and install a transmission on a 2007 ford freestyle sel

Transmisson repair shop & lots
of money in your check book

May want to start changing your trans & power
steering fluids every 3 years, on all the vehicles you
own from now on.

They fail for a reason,lack of knowledge mostly
Drive till it quits

Jul 15, 2014 | 2007 Ford Freestyle Limited

1 Answer

Had three fuel pumps installed on 2007 freestyle

Have you tried changing the fuel filter, Some model has inline filters on them. Just a suggestion.

Apr 24, 2014 | 2007 Ford Freestyle Limited

2 Answers

Brake rotor removal

you shouldn't need any special tool all you have to do is remove the caliper assembly of the rotor and the rotor should come right off. If not then the rotor should come off if a there is a nut holding it on there

May 10, 2013 | 2005 Ford Freestyle

1 Answer

Need to know location of factory reset code for keyless entry 2007 ford freestyle

You don't have to pay a dealer anything

You do have to go there to get the factory
code,then you can change to whatever you want,
if you have an owners manual or they write it down
for you

Not a reset code,just a security code

Oct 08, 2012 | 2007 Ford Freestyle

1 Answer

Location of "starter" for 1999 cadillac catera

Hi, if you have the 3.0 liter engine, see instructions below. If you have the 4.6 liter, the starter is under the intake manifold.

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Starter electrical connectors Right hand catalytic converter Right side engine mount nuts Intake air resonator to the throttle body ducts
  3. Install an Engine Support Fixture to the right side of the engine.
  4. Raise the right side of the engine approximately 1.5 inches (38mm) to gain access to the starter motor bolts.
  5. Remove or disconnect the following:

    Engine mount from the bracket and cradle Engine mount bracket bolts and reposition the bracket Starter motor

  6. jturcotte_2359.gif

    Fig. Remove the starter motor and bolts

To install:
  1. Install or connect the following:

    Starter motor. Torque the bolts to 44 ft. lbs. (60 Nm). Engine mount to the bracket and front crossmember. Torque the bolts to 30 ft. lbs. (40 Nm).
  2. Lower the engine into position and make certain that the mount locator tab is fully seated in the front crossmember slot.
  3. Remove the special tools from the engine.
  4. Install or connect the following:

    Engine mount nuts. Torque the upper nut to 30 ft. lbs. (40 Nm) and the lower nut to 41 ft. lbs. (55 Nm). Intake air resonator to the throttle body ducts Catalytic converter. Torque the bolt to 25 ft. lbs. (34 Nm) and the nuts to 18 ft. lbs. (25 Nm). Starter electrical connectors. Torque the battery cable nut to 115 inch lbs. (13 Nm) and the starter solenoid nut to 35 inch lbs. (4 Nm). Negative battery cable

Oct 03, 2011 | Cars & Trucks

1 Answer

Renault clio 1.5d timing marks diagram

special tools needed ,one to go through the bolt hole in front of engine block right hand side ,remove bolt and then screw special bolt/locating pin in ,common rail doesnt need timiing in as its only a pump ,cam is located by aligning sensor with lug on cam .This is not a do it yourself job special tools needed to lock the crank into position after removing starter motor as well also crank pulley is on a taper and the cam .better off taking it to a dealer

Oct 14, 2010 | Renault Fuego Cars & Trucks

2 Answers

Where is the starter located in the 1991 Chevy Lumina APV ??


3.1L Engine
Besides regular hand tools, a special oil pressure sensor socket will be necessary to complete this operation.

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the A/C compressor brace (if equipped).
  4. Extract the wiring harness from the retainer and position it out of the way.
  5. Remove the cover from the starter wiring.
  6. Remove the outer nut and disengage the wiring from the starter solenoid.
  7. Disconnect the electrical connector from the oil pressure gauge sensor.
  8. Using the special socket, remove the oil pressure gauge sensor.
  9. Unbolt the starter from the engine. Retain any shims.

To install:
  1. Install the starter to the engine, reuse any shims that were removed. Tighten to 32 ft. lbs. (43 Nm).
  2. Connect the wiring to the solenoid and install the outer nut.
  3. Place the cover over the starter wiring.
  4. Replace the oil pressure gauge sensor using the special socket.
  5. Plug the electrical connector onto the sensor.
  6. Mount the harness to the retainer.
  7. Install the A/C compressor brace (if equipped).
  8. Lower the vehicle.
  9. Connect the negative battery cable.

Oct 08, 2010 | 1991 Chevrolet Lumina Apv

Not finding what you are looking for?
2007 Ford Freestyle Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides