Question about 1994 Jeep Wrangler

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers


Rear Axle Notes

  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear axle seal in a 1995 jeep wrangler


the axle as 3 ends.
name just one.
left , right , front center.(pinion)

Sep 13, 2014 | 1995 Jeep Wrangler

1 Answer

How do I change rear axle seal on a jeep wrangler 1995


double posted word for word. and still
no mention of the 3 ends. left/right or center pinon...
sigh.

Sep 13, 2014 | 1995 Jeep Wrangler

2 Answers

Bad rear axle bearing and seal on a 2000 jeep grand


the bearing does not always have to be really bad for the seal to fail. Centrifugal force will throw axle grease outward where it gets on the rotor. That can make it feel like the rotor is out of round. If grease got on the brake pads I'd replace them and perhaps even the rotor. As far as the caliper being frozen, possible....check it out when you have it apart. You can have more than one shoe untied at the same time. Not always, but it can happen.
When replacing the seal make sure you put some grease on the lip before putting the axle back in. by doing that it won't fail from dry running before the diff lube reaches it.

May 15, 2010 | 2000 Jeep Grand Cherokee

2 Answers

95 Jeep Wrangler. When select 4wd lo or high,


there is a vacumn shift motor on your front passenger side axle. these are notorious for problems. check it to make sure it is working.

Feb 03, 2010 | 1992 Jeep Wrangler

1 Answer

4 wheel drive wont engage


I think the 94 wrangler still has the splice front axle with the vacuum control. It is located on the front axle on th pass. side . It is a large unit and is easy to see. Check vacuum lines.

Jan 07, 2010 | 1994 Jeep Wrangler

1 Answer

Transfer case won't engage the front differential. Transfer will shift into all ranges, but will not engage.


95 wrangler has a Split front axle, check the unit on the front axle pass. side. Make sure vacuum line are connected and good.

Dec 28, 2009 | 1995 Jeep Wrangler

1 Answer

Left front axle housing seal leaking. How do I replace


remove axel with screwdriver pry seal to replace place seal on housing and tap with hammer and socket that will fit on seal. then assemble all parts removed.

Jul 08, 2009 | 1994 Jeep Wrangler

1 Answer

1987 Jeep YJ [Wrangler] so owner ship says''


Our Jeep Wrangler YJ's are equipped with a vacuum module on the front axle. It is used to engage the front axle when the transfercase is shifted into 4WD. Check the vacuum lines on the front axle to make sure they are connected. The passenger side axle shaft has a disconnect sleeve that is moved left and right by the vacuum.

Mar 01, 2009 | 1987 Jeep Wrangler

1 Answer

How to Change Rear Axle Seal?


When you take the rear drum off, look where the axle goes in and if there are 4 bolts around it, you don't have to go into the diff. If there are no bolts holding the axle in, then get a repair manual to guide you through the steps. The seal on an axle that is bolted in place will have a collar that needs to be pressed off and a new one back on. These seals can be bought at a local partsd house.

Nov 09, 2008 | 1989 Jeep Wrangler

Not finding what you are looking for?
1994 Jeep Wrangler Logo

588 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...