Question about 2003 Chrysler PT Cruiser

Open Question

My 2003 PT Cruiser makes a rattling noise between 1500-2000 rpm from transmission.

It´s a New Venture Gear 5-Speed.The Noise is in every Gear when drivin.I changed the front Bearing from the Input Shaft before,cause of oil leak on the clutch.It is enough oil in the trany (org. atf+4)

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 2001 pt cruiser, make popping noise. would you

wheres it poping from motor or what lol

Posted on Nov 08, 2009

countrybo331
  • 79 Answers

SOURCE: I have a 2003 PT cruiser with turbo, When it warm

does it quit after it warm up or while driving it?your belts might be loose

Posted on Mar 23, 2010

gordanddar
  • 477 Answers

SOURCE: just had the timing belt changed for my 2004 pt

Hopefully something is just loose and rattling around. The bad alternative is that the timing belt job was botched. I would not drive the car , get the mechanic to come over and find the problem , or he can tow it back to his shop at his expense.

Posted on Mar 31, 2010

  • 14585 Answers

SOURCE: 2003 PT Cruiser. Check engine light, code cheked

if the noise is definitely coming from the tranny, you need to stop driving or get it to a shop before the tranny is completely destroyed. a rebuild is cheaper than a new one.

Posted on Jun 16, 2010

airjer995
  • 5332 Answers

SOURCE: 2003 pt cruiser front driver side wheel bearing

the wheel bearing is pressed into the knuckle and will require a machine shop service to press it in and out.

You will need to remove the knuckle from the vehicle.

-Remove the caliper from the knuckle.
-Remove the rotor.
-Disconnect the ABS harness if equipped
-Remove the bolt that holds the lower ball joint to the knuckle and separate them.
-Remove the outer tie rod from the knuckle.
-Remove the axle nut and tap the drive axle out of the hub.
-Remove the two strut mounting bolts from the knuckle
-Remove the knuckle from the vehicle.

A machine shop or an automotive service facility should be able to press the old bearing out and press in the new bearing for you. Call around for pricing and service availability.

Posted on Apr 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 pt cruiser makes rattling noise when put in drive


does it make the noise and goes away within 5 to 10 seconds then it drives and shift fine let me know ok

Nov 27, 2012 | 2003 Chrysler PT Cruiser

2 Answers

Jeep 360 rattle sound at idle in park


it could be a wrist pin, and im not sure if those amc's had hydraulic lifters but sometimes with old lifters when the oil pressure is lower at an idle the lifters arnt filling up all the way so they develope a little valve lash, and when the rpms are raised the oil pressure raises and fills the lifters. you could try chasing the noise down with an automotive stethoscope.

Mar 23, 2012 | 1985 Jeep Grand Wagoneer

1 Answer

2003 PT Cruiser. Check engine light, code cheked at auto parts store indicates a transmission issue. knocking noise when running but is loader at idle. Added ATF and got better, but noise came back.


if the noise is definitely coming from the tranny, you need to stop driving or get it to a shop before the tranny is completely destroyed. a rebuild is cheaper than a new one.

Jun 16, 2010 | 2003 Chrysler PT Cruiser

1 Answer

I have a 2003 pt that makes noise from the front end when you hit a bump in the road


I have a pt cruiser myself and love it but they have a problem with lower control arm bushings that wear out allowing the control arm to drop and smack on the sub frame. For the most part this is not dangerous unless the bushings are completely deteriorated.Also sway bar link pins rattle when they get worn. This is the lesser of two evils for the fix is alot cheaper i hope this helped:)

Oct 09, 2009 | 2003 Chrysler PT Cruiser

1 Answer

I have Crysler PT Cruiser. It jump when I put the gear in drive. What part should I replace?


check the idle speed .. it probably should be around 600 rpm .. if its higher then the transmission will jump ... that is probably controlled by an idle speed sensor ..

Oct 03, 2009 | 2003 Chrysler PT Cruiser

2 Answers

Rattles at high rpm


This is because of the problem with the clutch. So you better consult a technician to fix it up

Jul 22, 2009 | 1998 Ford Escort

6 Answers

2001 pt cruiser hear a thump noise


This is either caused by a wore out strut/shock in the rear of the car or a broken spring.

Jan 19, 2009 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
2003 Chrysler PT Cruiser Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...