Question about Seat Toledo

Open Question

Seat toledo 2007 where is the location off senes resistor

I've checked under footwell passenger and behind glove box

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: how to replace blower motor resistor on 2000 grand caravan

there will be two 8mm screws holdin it in.. with two connectors into it

Posted on Jan 05, 2009

  • 6982 Answers

SOURCE: Change flasher relay on Jeep Grand Cherokee 2007

If you are looking for the old style flasher, it's not there. It's now called a combination flasher module (more $$) and usually it's on the right side of the column under dash. If you buy one first, at least you will know what it looks like.

Posted on Mar 19, 2009

jsmes1027
  • 749 Answers

SOURCE: 2001 Grand Prix: Is the blower motor resistor on a Pontiac 2001 Gra...

It is behind and underneath the glove box back by the firewall. No need to pull out the glovebox.You may need to pull the carpet back to get to one of the bolts.

Posted on May 18, 2010

ZJLimited
  • 17970 Answers

SOURCE: where is the blower motor resistor in a 2001 dodge

Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Blower Motor - Removal & Installation

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.

    a1b7373.jpg
    Fig. The blower motor is located behind the glovebox, behind the blower motor cover
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.

    bdc6158.jpg
    Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

    063bc30.jpg

    Fig. The blower motor is secured to the housing with three small screws
  7. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.


Auxiliary Heater and Air Conditioner
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1dc958e.jpg
      Fig. Removing the trim panel to access the rear blower motor
    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    1e2cfdc.jpg
    Fig. The rear blower motor is held in place by four screws
To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember rated this).

Posted on Jul 11, 2010

  • 1 Answer

SOURCE: where is fuse for drivers side heated seat on 2006 Buick Terraza

i have a 2005 terraza and the fuse panel is at the end of the dash board on the passengers side .there is a finger slot in a plastic cover,pull to remove. fuse panel is behind .i had to call a service tech to find mine. good luck pete.

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My turn signals and hazard lights have stopped working in my estima 2001 where is the fuse box for these lights


There are 4 fuse boxes in a 2000 + Estima
one in the passenger footwell behind the glove box...
One in the drivers footwell behind the lower trim
2 under the bonnet..... one above the engine
pictures of there locations link below

http://www.teoc.ws/community/topic/19417-fuse-box-locations

Jan 30, 2016 | Cars & Trucks

1 Answer

HU-850 radio audio goes off & on along with a constant clicking. Any recommendation's?


I've got issues with my FM reception but the CD and other components have been rock solid since 2006. Check the amplifier unit under the front passenger seat. there are several cables under there that could get damaged by the seat moving up and back with something stuck under the seat. I think there's also a preamp behind the glove box that may have some audio connections.

Jan 23, 2016 | 2007 Volvo S60 T5 Sedan

1 Answer

How do I replace a ford focus 2005 fan speed control


see this and fix it. God bless you

Remove the passenger footwell lower trim panel underneath the glove box.

  • 2 Open the glove box and remove the screw holding the footwell air vent duct. Pull off the hose and remove the duct. Close the glove box.


  • 3 Disconnect the heater fan electrical connector. Remove the three bolts retaining the heater fan and remove the fan.
  • 4 Disconnect the heater fan resistor electrical connector, and remove the resistor.
  • 5 Install the new heater fan resistor by reversing the above steps.
  • Oct 04, 2012 | Ford Focus Cars & Trucks

    1 Answer

    Where is the heater blower resistor located in a 2000 Subaru Outback? I've seen one reply in a forum saying it is to the left of the blower motor, but I don't know where that is either. I need to...


    the blower motor is located under the passenger side of the dash. The blower motor resistor is located behind the glove box assembly. You will need to remove the glove box assembly and then you will see the resistor. It will have one connector with four or five wires and will be held to the HVAC unit with 2 screws.

    Jun 23, 2011 | 2000 Subaru Outback

    1 Answer

    Where is the heater fan/motor located?


    Up under dash behind glove box. easier to see if you remove glove box, or at least empty it and move tabs over and let it hang down. Curious, it obviously quit, or is very noisy? Has resistor been checked to make sure that's not the problem first? Wires from motor are attached to resistor up under where left foot would be on passenger side. Housing under motor to come off first then you will see the motor. If you need more info, let me know. I just did mine a couple of months ago.

    Feb 02, 2011 | 1999 Dodge Caravan

    1 Answer

    I have a primera p reg 2.0 diesel.Fan only works on 4.Been told it is the resistor pack.Is this really so and here is this foud/what does it look like.I have removed the glove box but not sure if I...


    this solution is a little late, but if not already done here is how to fix. yes its the resistor pack, i just fixed this on my 97 sentra. you are looking in the right place, taking the glove box out is how you get at it.

    to find the resistor pack you must locate the fan blower motor, its right behind the glove box near the passenger side footwell near the door. it is a big bulky looking cylinder. the resistor pack you are looking for should be to the left of the blower motor. it looks like a rectangle, the pack is held in by 2 phillips head screws. unscrew them and simply pull that piece out. it will look like a card at the back that will resemble a circuit board. once its out, replace with a new pack, screw the screws back in, put the glove box back and thats all. hardest part of the install is getting the glove box out, very easy to do took me 20 mins.

    Oct 30, 2009 | 1998 Nissan Sentra

    5 Answers

    Front blower fan not working. checked fuse and relay, not the problem. went out suddenly. what do i check next


    the blower motor, is replaceable, and it is cheap, is a diy job, with a 10mm socket go underthe dash no the passenger footwell and behind the glove compartement is the fan blower replace with a new unit.

    Jul 14, 2009 | 2001 Dodge Caravan

    2 Answers

    Still cant find ECU


    the ECU is located on the passenger side floorboard underneath the consold and carpet

    Feb 14, 2009 | 1992 Honda Accord

    2 Answers

    Locating heater blower motor resistor


    the resistor is behind your glove box. open the box and push in the sides to release it and let it hang down...the resistor is right there. I didn't try to replace it, a friend did it, but the part was under $20.

    Jan 21, 2009 | 2005 Dodge Caravan

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    17 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Seat Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Adam Truesdale

    Level 2 Expert

    265 Answers

    Are you a Seat Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...