Question about 2004 Isuzu Ascender

1 Answer

How to remove the floor trim of a 2004 Isuzu Ascender to put in speaker wire

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 20,706 Answers

If no screws there, look at kick panel ,take it off
see if there is trim screws there to start he process.
front to rear. if not, they pop off.

Posted on Dec 27, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 484 Answers

SOURCE: my gas mileage is horrible. what can i do to fix

Okay... K&N drop-in filter, NGK V-Power plugs (and NGK wires), run tires 2-4psi over manufacturer's recommendation, replace fuel filter anually, use a good fuel system cleaner every oil change, use synthetic oil in the crankcase, transmission AND differentials, drive with windows up and A/C off (just vents), drive 55mph on freeway (this one is HUGE), slow acceleration and try not to drive short distances. These are all "hyper-mileage" techniques that garner better fuel economy. If there is a mechanical problem causing the fuel economy to be bad, the spark plugs, wires and filters ought to be a help.

i hope this helps out,
matthew

Posted on Oct 23, 2009

johnjohn2
  • 5763 Answers

SOURCE: keys are stuck in the ignition of 2004 isuzu

the keys are going to stay stuck until the battery get power, your going to have to put jumper cables on it to get it out of park or keys out.

Posted on Jan 17, 2010

  • 94 Answers

SOURCE: my 2003 isuzu ascender won't start, when you crack

or you have a broken ground wire, an for shifting it mite nutaral safty switch.

Posted on Jan 31, 2010

  • 73 Answers

SOURCE: Is there a repair manual for a 2004 Isuzu

No, there is not one available. However, the Chevy Trailblazer is basically the same vehicle and there is a repair manual available for that.

Posted on Dec 14, 2010

Keef2011
  • 160 Answers

SOURCE: Just changed front wheel hub on 2004 isuzu

It probably needs resetting. When you replaced the hub, did you fit one for ABS? just a question i had to ask! Hope this helped.

Posted on Mar 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Isuzu Ascender keeps misfiring,losing acceleration and sputtering when stopped at a red light or stop sign. Changed camshaft position censor.Found oil all over the threads on two plugs


The first thing i would do is replace plugs after checking if wires areok. I thought my fuel pump was going out but all it was, was bad plugs and wires. i replaced them and my gas mileage went up 50%.

Jul 09, 2016 | 2004 Isuzu Ascender

1 Answer

Where on my 04 Isuzu ascender is the camshaft position sensor


On the I6 engine, it's on the front of the engine on the block near the camshaft. Directly below where you put your oil in.

Mar 10, 2015 | 2004 Isuzu Ascender

1 Answer

How do I remove the center console of a Isuzu Ascender


why not read on alldata.com, its all there,
remove a screw?


25402002-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg
  1. Block the wheels to prevent the vehicle from moving.
  2. Remove the rubber ash tray inserts and rubber mat from the console.
  3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
  4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
  5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
  6. Remove the center console retaining screws.
  7. Adjust the parking brake to the full-up, or fully engaged position.
  8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
  9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
  10. Disconnect the electrical connectors, as necessary.
  11. Adjust the parking brake to approximately the halfway position.
  12. Remove the center console from the vehicle.
  13. If replacing the floor console base, remove the following and retain for transfer:
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.
or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.

Feb 05, 2015 | 2006 Isuzu Ascender

1 Answer

I have a 2004 Isuzu axiom my check enegine is on .I put new sensors on it ,but the light is still on.


Most people have the misconception that a trouble code tells you what part to replace. The fact is the code tells the mechanic only what to check.
The problem could be a sensor, or a wiring harness, or something mechanical.

Aug 05, 2013 | 2004 Isuzu Ascender

2 Answers

Isuzu ascender 2004 ... headlights go off anytime they want ... sometimes for short periods of time and sometimes for days, all other lights work just fine including the high beams. what could be the...


Just solved this problem on our 2004 Isuzu Ascender. It was a bad relay located in the fuse/relay box which can be found inside the engine compartment. The relay is number 46 (HDM) on the diagram located on the inside cover of the fuse/relay box lid.

There are actually two of the same relays side by side in the fuse/relay box. To be sure this is the problem you can remove the relay from slot 45 and put in 46, the headlights should come on and stay on. Of course you will need to replace the relay which can be purchased and most GM/Chevy. The part number is: 15016745. I paid $52 for mine.

Oh, and be sure you use solid state relays only. The afore mentioned part number is a solid state relay.

Sep 22, 2011 | 2004 Isuzu Ascender

1 Answer

My 2003 isuzu ascender won't start, when you crack


or you have a broken ground wire, an for shifting it mite nutaral safty switch.

Jan 31, 2010 | 2004 Isuzu Ascender

1 Answer

Keys are stuck in the ignition of 2004 isuzu ascender. battery is dead and can't shift it into gear to push it out of the garag. any suggestions on what to do???


the keys are going to stay stuck until the battery get power, your going to have to put jumper cables on it to get it out of park or keys out.

Jan 17, 2010 | 2004 Isuzu Ascender

1 Answer

No warning chime for 2006 Ascender


I don't think it is a fuse.
The warning chimes for this vehicle come through the radio and are play to the speakers and if I remember correctly the chimes play to the left front speaker.
I would check for a faulty speaker or wiring to the speaker.

Sep 09, 2009 | 2006 Isuzu Ascender

Not finding what you are looking for?
2004 Isuzu Ascender Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...