Question about Cars & Trucks

1 Answer

Fg xr6 fan blower not working, wires going towards centre of dash plug melted?help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 660 Answers

Replace/repair wires, check fuse (most likely blown during the power wire getting grounded)

Posted on Dec 28, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 34 Answers

SOURCE: 7 wire harness going to blower motor resistor

There is an updated resistor/connector package. Very expensive from GM, try your local NAPA or other parts supplier for a replacement

Posted on Jul 09, 2009

  • 101 Answers

SOURCE: I'm working on 2000 chev S10 pickup. the blower

did you remove and inspect the blower motor resistor - a bad one can stop the blower and make for some hot wires

Posted on Oct 18, 2009

  • 59 Answers

SOURCE: Heat dial only works when "pushed" toward dash.

sounds like your brushes in the heater blower (remove molding panel BELOW glove box) 3 screws and a connector. If you have the original siemans motor still the brushes are at Ace Hardware use the EC type compound the are the OEM type
637 or 367 ?? which ever has SIDE wire NOT back wire. This motor brush assembly is separate so no problem putting back on THEN cover cap easy job 30 mins (on the loyale 93 you DON'T have to remove the glove box)

Posted on Nov 21, 2009

  • 90 Answers

SOURCE: heater blower will not shut off after ignition is

could be a faulty relay , pull relays out one by one and see if stops running

Posted on Mar 08, 2010

  • 2309 Answers

SOURCE: Anyone know anything about the wiring for a Ford

seems that taillights and dash lights are on the same circuit, they did that years ago so that if your dash lights went out you knew that you had no taillights, chech the grounds for the taillights, and check for voltage at the socket, from there its a search for broken wires

Posted on May 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Why is the blower for heat and air not working


Yes there are resisters that are mounted near the blower under the dash that can burn out. They are usually hard to get to but are the most common reason the blower will not work when there is nothing else wrong. This can also cause only certain speeds to work and not others.
The only other cause could be the switch itself has overheated and melted internally but this is more common in Fords.

Sep 11, 2014 | 2001 Chrysler Town & Country

3 Answers

Heater fan not working


try wiring it so it is key on hot

Mar 08, 2014 | GMC Safari Cars & Trucks

1 Answer

Dodge caravan air conditioning fan not blowing


I would turn the fan on with the van off and listen to see if just the blower is working at all or a slower speed. . If you have a volt meter you could make sure it was getting power by unplugging the wire to it and testing there.. If you have power then the blower motor is the problem . If it was a resister it would not work at all normally. or it would work on one speed but not another speed in most cases.. I would think by the age of it more likely a bad blower fan motor .the part is about 73 dollars to replace complete with fan and the resisters are 15-20 at your local auto parts store .
This could also be a wire harness issue with the resister plug which supplies the power to the blower . it very common that the wires got hot and melted from old age or from a blower that was old and drawing too much power .The resister and harness or located under the hood on the firewall of the passenger side of the van .Yes there is a fuse for the blower fan under the dash .If it has blown it could be the blower drawing too much power.or other issues .
Yes we sure do feel the heat here in Florida .

Replace blower motor Dodge Grand Caravan 1996 2000 chrysler Town Country...


Replace Blower Resistor for 2000 Chrysler Town and Country

Aug 16, 2017 | 2000 Dodge Caravan

2 Answers

Fan for heater dont work


the blower motor contorls the fan so I would get that checked

Jan 22, 2013 | 2003 Pontiac Grand Prix

1 Answer

Blower motor not working


One thing you may try is the fan resistor it controls fan speed just a thought hope this helps

Dec 31, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

2004 yukon xl the fan only works on high. was told it is the resistor. where is this resistor located?


the resistor is located in bottom of heater box under right side of dash it will be close to blower motor. the wires from blower motor go to resistor. check the plug and replace it as well they tend to melt

Mar 12, 2011 | 2004 GMC Yukon

3 Answers

Trouble shooting climate control intermitting blower problem # 5 speed has not been working for about 3 months # 1 2 3 4 speed is now working intermittingly


GMC has an ongiong problem with the blower motor resistor, look under the dash on the passenger side and you will see the blower housing, unplug the wireing harness that feeds it and look at the plug carefully you will see that the third pin from the left has been over heated and is melted a little. the repair is quick and easy go to your local parts store and purchase a new resistor and a replacement wireing plug, you will have to cut the old plug off and splice the new one in, replace the resistor and your done. I would recomend that the wires be and spliced cut one at a time so as to insure that they are put in the right location.

Sep 10, 2010 | 2005 GMC Envoy

2 Answers

Why doesn't ac blower work on number 5 setting? it is a chevy hd gas engine


Most likely the blower motor resistor. It's mounted next to the blower motor under the dash. Also check the 7 wire plug going to it, GM had a problem with that plug, and the wiring getting hot and melting. The plug is $68.00 from the dealership. One of my customer's car had the same problem.

May 25, 2010 | 2001 Chevrolet Silverado 2500HD

1 Answer

Location of fan resistor


the fan resistor is located by the blower motor. on a 2002 and newer there is about 6 or so wires on a thin flat plug. pretty close to it. I believe it is under a little cover. I know this might not be much help but it has been about 3 years since I replaced one. I do know the wires on the plug I described earlier will melt the plug sometimes, and the control head will go bad too sometimes so it could be any of these things. so dont get aggrivated if the resistor doesnt fixit although it might.

Dec 22, 2008 | 1995 GMC Sierra C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...