Question about 2000 Nissan Frontier

Open Question

How to replace windshield wiper linkage 2000 nissan frontier

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: Nissan Frontier torsion bar replacement

well it depends how you want to adjust it, if you want to lower it, back out the screw on the torsion key a couple of turns. raise, screw it in a couple of turns

Posted on May 29, 2008

  • 1 Answer

SOURCE: 97 nissan sentra windshield wiper linkage arm disconnected

Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Posted on Sep 14, 2008

  • 1 Answer

SOURCE: remove windshield washer reservoir

Take off the wheel well shroud. Firdt remove the front right wheel, it will be easier. Then remove the two screws holding in the tank. Remove the two electrical connectons and small rubber hose. Next (or first) grab the filler tube and twist while pulling it from the tank as it is held in by a rubber gromet. Then pull the tank forward and let it drop down. Nothing else is holding it in except the two screws. Removing the filler tube is a must!

Posted on Apr 21, 2009

  • 31 Answers

SOURCE: both Windshield wipers quit working at the same time

Its easy. 6 bolts hold that trim on remove them and gently remove the trim

Posted on Nov 02, 2009

  • 2 Answers

SOURCE: change brake light bulb on a 2000 Nissan Frontier

The entire bed line will need to be removed. The long screws that hold the metal bracet where the bed extender attaches also hold the tail light assembly in place.
I pulled the bed liner up at a 45 degree angle and layed it on top of the cab. This revealed the screws. Take both screws out and lay to the side along with the metal bracket for the bed extender.
Now firmly grab the edges of the tail light assembly and pull...there are 2 hard rubber nipples that snap in to hold the assembly. You will feel like you might break it but you won't..just pull straight back hard. The assembly will "POP" out and then you can just twist the back of each bulb there are (3) and pull out..now you will see the bulbs..just pull the bad bulb straight out and push the new one into place. Now just reassemble. Total time will be 30-45 min. for this repair.

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My winshield wipers are not moving. but I can hear the motor running when I turn them on.


please check the wiper linkages.try to move the wiper arm if moving repair the wiper linkages or replace it

Feb 17, 2011 | 1999 Nissan Frontier

2 Answers

How do I dismantle and reinstall a front wiper motor on a 2000 Kia Sportage?


moz-screenshot-6.pngmoz-screenshot-7.pngplay0027.gif
Wiper Motor

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the wiper motor electrical connector.
  3. Remove the four mounting bolts securing the motor to the firewall.
  4. Using a suitable prybar, carefully separate the wiper motor from the wiper linkage and remove the motor.

To install:
  1. Attach the wiper motor ball joint to the wiper linkage.
  2. Position the motor on the firewall and secure the motor with the four mounting bolts. Tighten the mounting bolts to 75 ft. lbs. (102 Nm).
  3. Connect the electrical connector.
  4. Connect the negative battery cable.play0027_0.gif

moz-screenshot-8.png

Nov 25, 2010 | 2000 Kia Sportage

1 Answer

The windshield wiper driver side does not move. Passenger side does. How do I get to it?


The wiper motor must be directly linked to the passenger side wiper, and the driver side wiper gets its action from the passenger motion. probably the linkage from passenger wiper to the driver side wiper must be the problem. Under the dashboard you can check it, the linkage must be snapped off. (safety first)

Sep 21, 2010 | 2000 Nissan Altima

1 Answer

Both Windshield wipers quit working at the same time


Its easy. 6 bolts hold that trim on remove them and gently remove the trim

Nov 02, 2009 | 2000 Nissan Frontier

1 Answer

How do I access the windshield wiper assembly?


You have to remove the wiper arms by prying off the black platic piece over the nut. Remove the nut and the wiper arms. There should be 5 places on the black plastic piece that runs the length of the windshield. Remove 4 of them by prying them out. The one is the middle is a screw. Pull away the plastic piece and you should have access to the mechanism below. I think you need to replace the linkage if it has fallen off.

Oct 03, 2009 | 1997 Nissan.5 Altima

1 Answer

Windshield wipers stopped working on 1998 Nissan Sentra. Is it a fuse problem? If so, where is fuse box and which fuse? Is it a motor problem? is this an easy diy fix?


Water can enter and displace the grease in the wiper arm linkage ball joint where the wiper linkage attaches to the wiper motor linkage.

This can result in gradual wear over a period of time inside the joint that could lead to the separation of the wiper linkage assembly from the wiper motor linkage at the ball joint. A loss of windshield wiper function can result when this separation occurs.

To prevent grease from being washed out of the joint, the dealers will modify by adding a water diversion seal that will prevent water from entering the windshield wiper linkage ball joint area.

Jun 13, 2009 | 1998 Nissan Sentra

1 Answer

Driver side wiper arm won't move


need to replace bushing on wiper arm take it apart and you will see. you can get the part at any part store. You WILL need a vice to press it in

Mar 22, 2009 | 2002 Nissan Frontier Crew Cab

9 Answers

97 nissan sentra windshield wiper linkage arm disconnected


Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Jul 13, 2008 | 1997 Nissan Sentra

Not finding what you are looking for?
2000 Nissan Frontier Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...