Question about 2001 Buick Park Avenue

Open Question

Cant get gas cap off 2001 buick park ave - 2001 Buick Park Avenue

Posted by on

  • Brett Duxbury
    Brett Duxbury Dec 25, 2016

    Hi Theda , we want to help you with your question, but we need more information from you. Can you please add details in the comment box?
    I know this is an obvious answer but have you looked in the user manual on how to take the gas cap off. Don't laugh this happened to me when I was at a servo with a different car the attendant asked me the exact smae question !

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: 91 buick park ave.

Well, that can be a ton of things. Usually it means: A. its not getting enough air, or any air. B. Its not getting enough gas. It could be a problem with the Mass flow Sensor- which can be cleaned or replaced-, or maybe a bad fuel pump or bad fuel lines or something. Either way the problem sounds like it just can't run because it can't get enough gas.

Posted on Aug 16, 2008

  • 12 Answers

SOURCE: fuse box location on 1998 buick park ave

RIght hand side of the car behind a panel...3 clips hold it pull it off...Under the hood same side of car MASTER fuse box.....GARY KNOWS ALL ANSWERED THIS

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: gas gauge stuck under tab

I had the same problem. I carefully removed the dash panel around the dash board (it just snaps out), undid the dash board mounting screws, took out the dash board assembly, disconnected it, removed the plastic lens, and gently turned back the needle. To make sure it didn't happen again I drilled a tiny hole opposite the little post already there (next to the full side) and screwed a tiny screw into it. I then put it all back together and it has worked ever since. While I had it a part I also put a tiny screw on the temperature gauge side so it wouldn't have the same problem. Good luck.

Posted on Apr 21, 2009

honeymokey
  • 3113 Answers

SOURCE: 1991 buick park ave. security system set off,

Did you try the drivers door lock cylinder?

Posted on Jul 20, 2009

  • 743 Answers

SOURCE: temp sensor for 1991 park ave

It is in front of the radiator, right below the latch on the hood.

Posted on Oct 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I disable the PK3 security on a 2001 Buick Park Ave?


easier to fix. have codes read ecm/bcm and security. should lead you to failed component

Dec 17, 2013 | 2001 Buick Park Avenue

1 Answer

No rear defog 2001 buick park ave


have windows ever been tinted? check the connection at the rear window itself. is the solder joint ok? if so, pull the switch and check the terminals for continuity

Nov 04, 2012 | 2001 Buick Park Avenue

1 Answer

2001 buick park ave stalls on first turn of key then starts on second


could be a weak fuel pump or a plugged fuel filter try a new fuel filter first

Oct 03, 2012 | 2001 Buick Park Avenue

1 Answer

2001 buick park ave high idle


First thing i would do is take the idle air control valve off and clean the carbon off of it and inside the throttle body using a non-chlronated brake cleaner.Then reset the computer with a code reader or a scan tool then start it and if problem still exists take the mass air flow sensor off and spray the thin wires inside the sensor with the same brake cleaner then let it dry for 15 minutes and re-install.Reset computer then start motor.

Jan 19, 2012 | 2001 Buick Park Avenue

1 Answer

1998 Buick Park Ave with trouble code p0440


Trouble code p0440 may be a simple as an improperly replaced gas cap, or a crack in one of the evap hoses.
Have the code cleared, if it comes back, find a shop that will do a "smoke test" to find the bad evap hose, and have it replaced.

Jun 16, 2010 | 1998 Buick Park Avenue

1 Answer

I cant locate where to put power steering fluid in my 1998 park ave ultra


The power steering pump cap is on the passanger side of the engine and between the engine and back fire wall. It is a very tight fit to get the cap off and back on.

Apr 15, 2010 | 1998 Buick Park Avenue

1 Answer

94 buick park ave. i have to belts on my car the


Lossen the altenater or the idler pulley.

Dec 19, 2009 | 1994 Buick Park Avenue

1 Answer

91 buick park ave.


Well, that can be a ton of things. Usually it means: A. its not getting enough air, or any air. B. Its not getting enough gas. It could be a problem with the Mass flow Sensor- which can be cleaned or replaced-, or maybe a bad fuel pump or bad fuel lines or something. Either way the problem sounds like it just can't run because it can't get enough gas.

Aug 16, 2008 | Buick Park Avenue Cars & Trucks

Not finding what you are looking for?
2001 Buick Park Avenue Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...