Question about 2004 Mazda 6

Open Question

I have engine oil coming down to the airfilter 04 mazda 6 3.0

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2004 mazda 6 starter

the starter is located on top of the engine, underneath the battery and battery tray. they must be removed to gain access to the starter

Posted on Feb 08, 2009

Ad
roniecon
  • 6826 Answers

SOURCE: engine misfire

It sounds like the coil is going out on that cylinder,but replace the boot with the coil.It would not hurt to use a injector cleaner first,Lucas is the best.

Posted on Jan 26, 2010

Testimonial: "thanx for the promt response and helping me pinpoint the problem"

  • 96 Answers

SOURCE: my 04 mazda 6 at light comes on?

its probly not giving a charge. 2 check this. take the positive post off when its started if it stalls the alternator isnt charging

Posted on Feb 13, 2010

  • 608 Answers

SOURCE: mazda 6 2o diesel replaced turbo new unit same

There is a oil drain return from the turbo charger to the sump. If the sump oil level covers the outlet into the sump, oil will build excess pressure tin the turbo causing the sealing rings to leak oil in to the intake manifold. This would cause smokey exhaust and loss of oil. Try this. Drain the sump completely, refill with the exact quantity of oil to Mazda spec. Dip the oil and if the new oil level is lower than the full mark on the dipstick, you have found the cause of the problem. Mark this new level with a scriber or file and fill only to this new level. Hope this is the solution.

Posted on Mar 23, 2010

  • 7353 Answers

SOURCE: can i replace my mazda 6 2.3 v4 for a 3.0 v6

Not unless you have the whole other complete car to swap parts from. starting with the wiring harness.

Posted on Apr 23, 2010

Testimonial: "Tanx for the wiring harness info.. i didnt know great...."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil light flickering and knocking noise on 04 Mazda 6


oil pressure senor would be my first guess.if that checks out possible oil pick up blocked
or worst case worn crank bearings but i doubt it at the age of the car
fuel pressure side of it, could be possible fuel pump

Apr 09, 2013 | Mazda MAZDA6 Cars & Trucks

1 Answer

Accelerator sticking problem


Could be dirt or varnish inside the throttle body. Could also be a sticking idle air control valve.
Is the check engine light on ?

Aug 23, 2012 | 2005 Mazda 6

1 Answer

I have a 2005 mazda 6. it was 2 qts low on oil, i added oil, the car ran fine but had a slight rattle. 2 days later, i was sitting at a stoplight and the car died. my mechanic says the engine seized. no...


Hi . Unfortunately it's a common problem with mazda6 engine.When they run low on oil the crank shaft tend to get damaged.And some times people tend to top up oil rather than changing oil between 6000 &10000kms .Yep the engine is seized cost less replacing the engine than repairing it.good luck....

Jan 05, 2011 | 2005 Mazda 6

1 Answer

Can i replace my mazda 6 2.3 v4 for a 3.0 v6


Not unless you have the whole other complete car to swap parts from. starting with the wiring harness.

Apr 22, 2010 | 2004 Mazda 6

2 Answers

My 2004 mazda 6 engine fan runs long after i turn off the engine...coolent is fine...no other explainations...any help?


I had this problem on my 04 v6 6. there is a fan relay that went out. dealer covered it under warranty.

May 09, 2009 | 2004 Mazda 6

1 Answer

2004 Maxda 6 sputtering


hey, I own an 04 v6 mazda 6 as well and recently had that same problem. Its an ignition coil. The thing is that you have to wait until the check engine light comes on to know whick cylinder it is. I replaced all my spark plugs and boots all at once thinking it would solve the problem but it didnt work. It takes a while for the light to come on so what I did was to push my engine and make it come on. Hopefully its one of the the three coils in the front or else it would be a pain to get the back three. Each coil will run you about 50-80 dollars. Call me if you have any questions. My name is Carlos.786-210-1493

Apr 27, 2009 | 2004 Mazda 6

2 Answers

2004 mazda 6 starter


the starter is located on top of the engine, underneath the battery and battery tray. they must be removed to gain access to the starter

Feb 02, 2009 | 2004 Mazda 6

3 Answers

2005 MAZDA 6 "using" or "burning oil"


This problem sounds like ablown head gasket, this would make the oil mix in with the gas and would result in discolored smoke out of the exhaust pipe.

Jan 04, 2009 | 2005 Mazda 6

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...