Question about 2006 Cadillac DTS

1 Answer

Torsion Bar on Cadillac dts 2006 fell off but isn't broke, how do I put it back on. Amy suggestions or links showing how to install?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cadillac Master
  • 646 Answers

Whatever fell off isn't a torsion bar - there isn't one. For help, describe the part better (a picture would help).

Posted on Jan 02, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: 2008 Cadillac DTS navigation manual

try www.edmonds.com

Posted on Mar 21, 2009

  • 4044 Answers

SOURCE: how to remove head light in 2006 dts cadillac

ok, In this New of a vehicle there are no screws holding the headlight in if you just need to replace a headlight because it is burned out. Look at the back of the light where the wires attach and you should see the wires going into what appears to be a coupling. Get a hold of that and turn. After it unlocks you can remove and replace the bulb. If you are replacing the Headlight assembly because it was damaged there are typically 2 long scews on the top front that appear to be adjsutment screws and 2 smaller ones in each side, again on top. Good Luck

Posted on Aug 27, 2009

MNfisherman
  • 11896 Answers

SOURCE: how to change spark plug on 2006 cadillac DTS

The plugs are located by engine head. You can use a ratchet wrench and sockets to remove them. Make sure to mark the plug wires so the order doesn't get mixed up.
The check engine light comes on when there is a bad sensor, or bad circuit.
Many part stores will run an engine diagnostic code scan for free which will pinpoint exact problem that is setting of the check engine light
The light can only be shut off by the diagnostic scanner!!

Posted on Nov 23, 2009

  • 9 Answers

SOURCE: 2006 cadillac dts - one of the headlights want

Have you changed the bulb on that side of the car? If a bulb is broken or burnt out it will not light up.

Posted on Dec 18, 2009

  • 280 Answers

SOURCE: how do you change the headlight bulbs on a 2006

you should have to go thru under the hood to the backside of the lamp assembly. There should be either a hard plastic cap or a plastic dust cover that has the wires going thru it to the lights. If it is the hard cover (looks like a jar cap) turn it 1/4 turn counterclockwise and pull it out of the way. Take the bulb/socket out. Unclip the old one- Put the new one in. (DO NOT TOUCH THE GALSS PART OF NEW BULB). Then re-assemble

Posted on Mar 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing broken torsion bar and how do you install it.


Ther is a bolt that adjusts the tension near the rear othe the bar, back it off , jack it up under the frame , not the a arm , put jack stand under frame , then jack under a arm , remove bottom shock bolt and ball jioint nut , separate , you may have to unhook sway barl link let arm down replace torsion Barr reassemble and adjust tension with adjustment bolt

Aug 08, 2016 | Cars & Trucks

1 Answer

Where is egr valve located on 2006 Cadillac DTS


I'm not familiar with your vehicle (I'm in the UK). However, the EGR valve is usually connect to the air intake.

Look for a 'unit' that is connected to the air intake via a tube.

Here's a link done with a general Google search for '2006 Cadillac DTS egr'. Hopefully you will recognise your own egr valve amongst the images:

2006 Cadillac DTS egr Google Search

Feb 24, 2016 | Cadillac Cars & Trucks

1 Answer

I didn't mark the torsion bar when I took it out, how do I install it without the marks


jack the car right up with the wheels off the floor
install the torsion bar with the adjuster bolt unscrewed all the way off
fit the bar and lower the car back onto the floor so that all the weight is on the torsion bar
it should be sitting a bit low at this point
adjust up the adjuster bolt to when it sits level
if there is not enough adjustment the jack up the car again
let the adjuster right off an this time use a pipe wrench ( stiltsons ) to turn the bar against the stop plate a spline then insert it into the housing
this preloads the bar before any adjustment
lower the car and again adjust the bolt
EXTREME CARE AND VEHICLE STANDS SHOULD BE USED AS THE CAR COLLAPSING CAN CRUSH THE PERSON UNDERNEATH

Oct 20, 2015 | 1976 Cadillac Eldorado

1 Answer

Why will driver doorl only open from inside the car?


The outside door handle broke ! you can only see what broke by taking the door panel off . It's plastic an they break ! $47.95 new 1Aauto . This video is just to show you what has to be done to get to it ! 2006 2011 Cadillac DTS Paint to Match Outside Door Handle Rear Driver Side How To Install Replace Outside Front Door Handle Cadillac DeVille 94 99...

Aug 23, 2014 | 2007 Cadillac DTS Sedan

1 Answer

Replace struts 2006 cadillac dts


unbolt and remove after putting car on stands or hoist

Jan 21, 2014 | 2006 Cadillac DTS

1 Answer

How to change headlight 2006 cadillac dts


Here's the link I used when I was changed my headlight. http://www.carcarekiosk.com/video/2009_Cadillac_DTS_Platinum_4.6L_V8/lights/headlight

Nov 04, 2010 | 2006 Cadillac DTS

2 Answers

What is the torson bar on jimmy and where can you get the part for it?


1995-2005 Models NOTE: The following procedure requires the use of the torsion bar unloader tool No. J-36202 or equivalent.
  1. Raise and safely support the vehicle.
  2. Remove the transmission shield, if equipped.
  3. Install a torsion bar unloader tool to relax the tension on the torsion bar adjusting arm screw; record the number of turns necessary to properly install the tool. Remove the adjusting screw and the unloader tool.
  4. Unfasten the lower link mount nut from one side, then disengage the torsion bars. NOTE: Note the direction of the forward end and side of the torsion bar being removed
  5. Remove the lower link nut from the opposite side.
  6. Remove the lower link mount, upper link mount nut, upper link mount and then unfasten the torsion bar from the frame.
To Install:
  1. Install the torsion bar and support.
  2. Install the upper link mount and mount nut.
    • Tighten the nut to 33 ft. lbs. (45 Nm) on 1995-96 models and 48 ft. lbs. (65 Nm) on 1997 and later models.
  3. Place a jack under the torsion bar to release tension, then install the lower link mount bushing and nut.
    • Tighten the nut to 13 ft. lbs. (18 Nm) on 1995 models, 50 ft. lbs. (68 Nm) on 1996-98 models and 37 ft. lbs. (50 Nm) on 1999 and later models.
  4. Install the torsion bar unloader tool and tighten the tool against the adjusting arm the same number turns recorded earlier, then remove the tool. This loads the torsion bars.
  5. Install the transmission shield, if removed.
  6. Remove the jackstands and lower the vehicle.
  7. Check and adjust the Z height as outlined in the wheel alignment portion of this section.
prev.gif next.gif

Jul 08, 2010 | 1997 GMC Jimmy

1 Answer

How to install trunk lid torsion bars


one of those bars come out of its bracket ( on my 89 cougar)
none of the local shops would touch it, no even the body shops.
so i just connect one end to the lid, like normal, then with a pry bar, pryed out the other end and put in a small block of wood (two by four) then released the pry bar. took another bite pryed it out again then added another block until i got the desired spring back into the torsion rod. yes that's (jury rigged) but my trunk works almost like it should. if you need i can send you a picture of what i did.

Feb 19, 2009 | 2005 Lincoln LS

Not finding what you are looking for?
2006 Cadillac DTS Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...