Question about 2000 Lincoln Town Car

1 Answer

Where is the control module located on the 2000 Lincoln town car for the air suspension system???

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Lincoln Expert
  • 144 Answers

You have a height sensor under the car but what are you trying to do so I can help you skeetersmail1@yahoo.com in the trunk you have a shut off switch

Posted on Aug 03, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
RJones1125
  • 373 Answers

SOURCE: where is air suspension compressor located on '94 lincoln towncar

engine compartment, driverside fender well

Posted on Feb 28, 2009

slfowler29
  • 51 Answers

SOURCE: Locate the Idle Air Control Valve.

The IAC is at the back of the engine on the left side

Posted on Mar 23, 2009

  • 3 Answers

SOURCE: Air Suspension Fuse 2000 Lincoln town Car

look in ur manual it will say it in there or u can call ur dealer and ask them which fuse it would be......

Posted on Apr 09, 2009

  • 1 Answer

SOURCE: Air Rise Suspension/computer module

i went to auto zone and bought coil springs for my 93 town car went home jacked it up disconnected the air bags pulled them out put springs in let it down and was driving in less than 45 minutes. at a cost less than $200.

Posted on Feb 23, 2010

  • 1 Answer

SOURCE: Where is the control module for the air suspension

2001 lincoln rides to hard and on dash says ride data error

Posted on Jul 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the rear air suspension control module located on a 2010 lincoln town car?


Hi,you have to remove the air intake box top and bottom and the compressor is underneath,hope this is what you ment only trying to be of help,all the best.

Mar 13, 2018 | Lincoln Cars & Trucks

2 Answers

96 grand marquis...air suspension light stays on all the time...system seems to work fine otherwise...


If everything is working fine, then you need to decide if it is worth the time and expense of repairing the circuit that leaves the light on when it should be off. I would leave it alone and if the lamp bothers you that much you can remove it or cover it with a piece of black tape.

Jul 25, 2015 | Cars & Trucks

1 Answer

I have a 2001 town car with a suspension problem. I just replaced the air bags. A month later the pump started to run too much. I tried soapy water but found no leaks.Yesterday the back end droped and the...


Having it hooked up to a factory scan tool would be your best bet . Check for DTC'S diagnostic trouble codes . Without testing ,code scan ,we'd only be guessing .
Very complex , the untrained person hasn't got a pray of fixing this . You have no idea what your dealing with . Vehicle Dynamic Suspension The vehicle dynamic suspension consists of the following components:
  • Rear air suspension control (RAS) module (5A919)
  • Snorkel
  • Drier
  • Air compressor (5319)
  • Air suspension switch (5K761)
  • Solenoid valve (5311)
  • Air spring (5560)
  • Air suspension height sensor (5359)
  • Air line
  • Rear Air Suspension Control Module
    A microprocessor controls the air suspension system. The microprocessor and its supporting hardware are contained in the rear air suspension control module. The rear air suspension control module responds to signals from various sensors in the vehicle to maintain the programmed ride height while the vehicle is either moving or stopped. The rear air suspension control module accomplishes this by opening and closing solenoid valves to control the amount of air in the air spring(s). The rear air suspension control module turns on the compressor by applying voltage through the compressor relay to inflate the air spring(s) and raise the vehicle. The rear air suspension control module opens the vent solenoid to lower the vehicle by releasing air from the air spring(s) in response to signal inputs from the air suspension height sensor(s).
  • Rear Air Suspension Control Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1317 Battery Voltage High Rear Air Suspension Control Module GO to Pinpoint Test C . B1318 Battery Voltage Low Rear Air Suspension Control Module GO to Pinpoint Test C . B1342 ECU Is Defective Rear Air Suspension Control Module INSTALL a new rear air suspension control module. REFER to Module-Air Suspension Control . TEST the system for normal operation. C1441 Steering Sensor Channel A Circuit Failure Rear Air Suspension Control Module REFER to Section 211-00 . C1442 Steering Sensor Channel B Circuit Failure Rear Air Suspension Control Module REFER to Section 211-00 . C1722 Air Suspension Height Sensor Power Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test D . C1723 Air Suspension Height Sensor Power Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test E . C1760 Air Suspension Rear Height Sensor High Signal Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test F . C1763 Air Suspension Rear Height Sensor High Signal Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test G . C1765 Air Suspension Rear Height Sensor Low Signal Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test F . C1768 Air Suspension Rear Height Sensor Low Signal Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test I . C1773 Air Suspension Vent Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test J . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test K . C1793 Air Suspension LR Air Spring Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test L . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test M . C1798 Air Suspension RR Air Spring Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test N . C1813 Air Suspension Vent Request Exceeded Max Timing Rear Air Suspension Control Module GO to Pinpoint Test O . C1818 Air Suspension Air Compressor Request Exceeded Max Timing Rear Air Suspension Control Module GO to Pinpoint Test P . C1830 Air Compressor Relay Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test Q . C1832 Air Compressor Relay Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test R . C1840 Air Suspension Switch Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test S . C1842 Air Suspension Switch Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test D . C1897 Steering VAPS Circuit Loop Failure Rear Air Suspension Control Module REFER to Section 211-00 . U1041 SPC Invalid or Missing Data for Vehicle Speed

Nov 12, 2017 | 2000 Lincoln Town Car

1 Answer

Wiper control module location


the wipers are controlled by the lighting control module

Apr 10, 2013 | 2000 Lincoln Town Car

1 Answer

Where is the suspension control module in a 1999 lincolin towncar


Turn air suspension switch off, disconnect neg, side battery, remove panel under glovebox control module located fwd up in frnt of air tube. If replaced the computer will have to re learn driving conditions this could take a few miles of driving.

Feb 22, 2012 | 1999 Lincoln Town Car

2 Answers

I have a 1995 Town Car Signature Series. The rear


Sadly, there is no way to turn the light off. I had the air suspension on my Lincoln replaced with the spring kit, and the light is still on. I had a friend take the instrument panel apart and place a small piece of electrical tape over the "check suspension" light. Also, be certain to turn the air suspension pump switch off. It is located in the trunk on the right side.

May 29, 2010 | 1995 Lincoln Town Car

2 Answers

Can any one tell me were how i can find the automatic level control on my 1994 town car


Description and Operation The rear air suspension:
  • Is an air-operated, microprocessor-controlled, suspension system.
  • Replaces the conventional rear coil spring suspension.
  • Provides low spring rates for improved ride and automatic rear load leveling.
  • Is standard equipment on the Town Car.
  • Is available as optional equipment on Crown Victoria and Grand Marquis.
The rear air suspension system has the following features:
  • The system is operational with the ignition switch in the RUN position.
  • Automatic rear load leveling has limited operation for one hour after ignition switch is turned to OFF.
  • The air suspension switch, located on the right side of the luggage compartment, must be turned OFF when the vehicle is on a hoist, being towed or jump started.
  • The Air Suspension warning indicator is located in the instrument panel, to the right of the speedometer.
    • The warning indicator flashes five times and then stays on when service switch is turned off or a system malfunction is detected.
  • The rear leveling system operates by adding or removing air in the springs to maintain the level of the vehicle at a predetermined rear suspension D ride height dimension, and is controlled by a control module (5A919) .
  • The rear air suspension control module also controls the electronic variable orifice (EVO) steering.
  • Refer to Section 11-02 for Description of the EVO steering system.
  • Air required for leveling the vehicle is distributed from the air compressor to the rear air springs by a nylon air line which runs from the compressor air dryer (5346) through a Y-fitting to each individual air spring.


Suspension, Computer Controlled—Town Car

c441c13.gif
Item Part Number Description 1 9C392 Compressor Relay Power Junction Block 2 5A897 Air Line (Attached to Brake/Fuel Bundle) 3 5319 Air Compressor With Regenerative Air Dryer and Vent Solenoid 4 5A897 Air Line to Compressor 5 5K761 Air Suspension Service Switch 6 14489 Data Link Connector 7 — Quick Connect 8 — To LH Air Spring 9 — From Compressor 10 — Y-Fitting (Part of 5A911) 11 — To RH Air Spring 12 5A908 Heat Shield 13 5A966 Spring Retainer Clip 14 5560 Rear Spring 15 5359 RearAir Suspension Height Sensor 16 5A919 Control Module 17 14018 Air Spring Solenoid

Control Module Power and Ground The control module (5A919) has the following features:
  • Power is provided by Circuit 418 and is controlled by the air suspension switch.
    • The air suspension switch is powered through a 15 amp fuse in Circuit 296 in Town Car.
    • AIR SUSPN PUMP (30A MAXI) fuse provides this power through Circuit 414 in the Crown Victoria/Grand Marquis.
  • Control module ground is provided through control module wire harness Pins 6 and 21, to the RH inner quarter panel sheet metal, near the control module .
---------------------------------
Weight Added When weight is added to the vehicle:
  • The air suspension height sensor (5359) length is reduced from trim length, sending a "rear is low" signal to the control module (5A919).
  • The control module then turns the compressor on by grounding the compressor relay control Circuit 420. This restores the rear of the vehicle to trim position.
    • Battery voltage is provided to the relay coil by Circuit 414.
  • The control module opens the spring solenoid valves (5311) by switching Circuits 416 and 429 to ground. This allows pressurized air to enter the springs.
    • Battery voltage is provided to the air spring solenoid valves by Circuit 414.
  • Compressed air flows from the compressor, through the compressor air dryer (5346) airlines and spring solenoid valves into the rear springs (5560).
  • As the rear springs raise the rear body height, the air suspension height sensor increases in length until the preset trim height is reached.
  • The control module then turns off the compressor (through the relay) and closes the air spring solenoid valves.
----------------------------------------------------------------------
Weight Removed When weight is removed:
  • The air suspension height sensor (5359) length is increased from the trim length, sending a "rear is high" signal to the control module (5A919).
  • The control module then opens the vent solenoid valve (located in the compressor assembly) by switching Circuit 421 to ground and opens the solenoid valves (5311) by switching Circuits 416 and 429 to ground. This restores the rear of the vehicle to trim position.
  • Compressed air flows from rear springs (5560), through the air spring solenoid valves, air lines, compressor air dryer (5346), and out the vent solenoid valve.
  • As the body lowers, the air suspension height sensor length decreases until the preset trim height is reached.
  • The control module then closes the vent and solenoid valves.
-----------------------------------------
Control module operates as follows:
  • In general the control module uses a 45-second averaging interval to determine when compress and vent operations are needed.
  • However, door courtesy lamp switch (13713) inputs can override the 45-second averaging interval so compress and vent operations can begin immediately, if needed.
  • The 45-second averaging interval is used to keep the control module from making unneeded corrections.
  • When a vehicle at the correct rear trim height hits a bump, the air suspension height sensor output will read low and high in addition to trim until the oscillations die out.
  • If the control module were to correct for these "bump induced readings", system duty cycle would increase unnecessarily.
  • The 45-second averaging interval not only eliminates corrections due to bumps, but also eliminates unneeded corrections resulting from braking, accelerating, and turning. The control module tabulates the air suspension height sensor readings, and does not begin a compress or vent operation until the air suspension height sensor (5359) reads low or high for 45 seconds consistently.
  • There are more restrictions on vent operations than there are on compress operations.
  • To eliminate the chance of catching a door on a curb as the vehicle vents down, the control module will not allow any venting to occur when a door is open.
  • The control module does not allow any vent operations for the first 45 seconds after the ignition switch (11572) has been turned to RUN.
    • Even if a vehicle is extremely high in the rear, DO NOT expect it to vent until the ignition switch has been turned to RUN for 45 seconds.

Jun 24, 2009 | 1994 Lincoln Town Car

1 Answer

Air Suspension Fuse 2000 Lincoln town Car


look in ur manual it will say it in there or u can call ur dealer and ask them which fuse it would be......

Apr 09, 2009 | 2000 Lincoln Town Car

Not finding what you are looking for?
2000 Lincoln Town Car Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

80668 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...