Question about 2011 Kia Sportage

Open Question

How do I remove outer intake manifold cover on 2.4l Kia sportage 2011

Posted by on

  • Craig Kephart Dec 24, 2016

    It's the air duct on front, radiator side, of engine. Found 2 bolts.....



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


SOURCE: Can't remove intake manifold on 94 Chevy 5.7L TBI

Yes, the allen bolts need to come out.

Posted on Jan 05, 2009

  • 17 Answers

SOURCE: intake manifold cover

remove oil cap steam an it should just lift off

Posted on Feb 23, 2009

  • 1 Answer

SOURCE: vacuum leak

mine is doing the same, it's your pcv receptor on the manifold. that hard plastic cover is actually part of the intake itself, if it "came off" it would cut your intake in half. that seem seals the two halfs together. you gotta pull the whole intake off and replace it... or jimmy rig it.

Posted on May 16, 2009

  • 3 Answers

SOURCE: trouble code po171 for engine running lean

where the hell do i find a 1996 ssangyong musso vaccum hoses diagram that is readable because i have the work shop manual and it shows me bugger all

Posted on Apr 06, 2010

  • 387 Answers

SOURCE: how do it remove the intake manifold?

its easy my friend, take your tools, drain engine oil and coolant, remove left side rocker ornament and air duct of intake manifold, collector,hose wires, harness etc, remove ignition coils, egr tube,intake manifold collector supports and the manifold( right cylinder head only,) remove intake manifold, and replace knock sensor to avoid some trouble in the future

Posted on Jun 26, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Kia Sportage 2011 fuel consumption problem

Bad carberator or needs a carborator adjustment.

Could also be dirty air intake.

Aug 19, 2016 | 2011 Kia Sportage 2.4

1 Answer

Can't find where the sparkplugs are

There under the air intake manifold little black cover with six bolts remove them there they are

May 26, 2012 | 1996 Kia Sportage

1 Answer

Knock sensor for a 2002 2.0 kia sportage

1. Remove the intake manifold support bracket
2. Disconnect wire harness
3. Loosen bolt remove harness

Mar 17, 2012 | 2002 Kia Sportage

1 Answer

How do I remove the starter on a 2000 Kia Sportage with 4WD?

It has three bolts that need to be removed. There is a support bar attached to the engine block and bottom of intake manifold. Remove this and the starter will drop down.

Nov 21, 2010 | 2000 Kia Sportage

1 Answer

Replacing motor in my 2005 KIA Sportage and need the "proper name" of the intake manifold gasket that sits over top of the spark plugs. Have called local kia dealership but they said that there are...

Does it look like this? (copy and paste in your address bar)?

If so that is called the plenum gasket, or intake plenum gasket. There are available aftermarket, places like NAPA should have or be able to get them. It is a common gasket to replace because of the necessity to remove the plenum to do a tune-up. NAPA gets about $7 for the gasket.

Oct 22, 2010 | 2005 Kia Sportage

1 Answer

Locate spark plugs on 2001 kia sportage

the spark plugs are located in the head. you must remove the upper half intake manifold first, it has three bolts 12mm. then remove the black plastic cover down the center of the valve cover, six 10mm bolts. remove the two coils and plug wires. now you have access to your spark plugs. Good Luck

Apr 18, 2010 | 2001 Kia Sportage

1 Answer

Location of the knock sensor on a 2002 kia sportage

remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley u might wanna google knock sensor so u knoe what it looks like

Feb 19, 2010 | 2002 Kia Spectra

1 Answer

Starter for kia sportage 2000

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter

    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

2 Answers

I have been looking for a repair manual for a 99

# Properly relieve the fuel system pressure.

# Drain the cooling system.

# Remove or disconnect the following:

Negative battery cable

Brake booster vacuum hose from the dynamic chamber

Fuel line from the pressure regulator and the return line from the rear of the dynamic chamber

Ground wire from the intake manifold

Purge solenoid valve vacuum hose

Upper radiator hose

Intake manifold support bracket

Converter flange inlet pipe

Timing belt

Cylinder head cover

Cylinder head with the intake and exhaust manifolds attached

3 wire harness connectors at the rear of the cylinder head


May 14, 2009 | 1999 Kia Sportage

Not finding what you are looking for?
2011 Kia Sportage Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

77932 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides